User's Manual

Chapter 9 HiveOS
148 Aerohive
Figure 6 Relationship of Current, Backup, Bootstrap, and Default Config Files
To create and load a bootstrap config, make a text file containing a set of commands that you want the HiveAP to
load as its bootstrap configuration (for an example, see "Loading a Bootstrap Configuration" on page167). Save the
file locally and then load it with one of the following commands:
save config tftp://ip_addr:filename bootstrap
save config scp://username@ip_addr:filename bootstrap
After it is loaded, you can enter the following command to view the bootstrap file: show config bootstrap
If you want to run the bootstrap config, enter the following commands:
load config bootstrap
reboot
When the bootstrap config loads, enter the login parameters you defined for that configuration. To return to your
previous current config file, enter the following commands:
load config backup
reboot
Note: Similar to the way that a current config consists of the commands you added on top of the default config,
a bootstrap config consists of default definitions and settings plus whatever other settings you configure.
ɸ»² §±« »²¬»® ¬¸» ®»-»¬ ½±²º·¹ ½±³³¿²¼ ±® °®»-- ¬¸»
®»-»¬ ¾«¬¬±² ±² ¬¸» º®±²¬ °¿²»´ ±º ¬¸» Ø·ª»ßÐ ¼»ª·½»ô ¬¸»
Ø·ª»ßÐ ¼»´»¬»- ¬¸» °®»ª·±«- ½«®®»²¬ ½±²º·¹ô ®»¾±±¬-ô ¿²¼
´±¿¼- ¬¸» ¾±±¬-¬®¿° ½±²º·¹‰ ·º °®»-»²¬‰±® ¬¸» ¼»º¿«´¬ ½±²º·¹ò
®»-»¬ ½±²º·¹
Ý«®®»²¬ ݱ²º·¹
Þ±±¬-¬®¿° ݱ²º·¹
Ü»º¿«´¬ ݱ²º·¹
ò ò ò ±® ·º ¬¸»®» ·- ²± ¾±±¬-¬®¿° ½±²º·¹ ò ò ò
λ-»¬¬·²¹ ¬¸» ݱ²º·¹«®¿¬·±²
Ý«®®»²¬ ݱ²º·¹ Þ¿½µ«° ݱ²º·¹
Þ±±¬-¬®¿° ݱ²º·¹
Ü»º¿«´¬ ݱ²º·¹
ò ò ò ±® ·º ¬¸»®» ·- ²± ¾±±¬-¬®¿° ½±²º·¹ ò ò ò
׺ ¬¸» Ø·ª»ßÐ ½¿²²±¬ ´±¿¼ »·¬¸»® ¬¸» ½«®®»²¬ ±® ¾¿½µ«°
½±²º·¹ º·´»-ô ·¬ ¼»´»¬»- ¬¸»³ô ®»¾±±¬-ô ¿²¼ ´±¿¼- ¬¸»
¾±±¬-¬®¿° ½±²º·¹‰ ·º °®»-»²¬‰±® ¬¸» ¼»º¿«´¬ ½±²º·¹ò
ݱ²º·¹«®¿¬·±² Ú¿·´±ª»® Þ»¸¿ª·±®
Ú¿·´±ª»® Ú¿·´±ª»®