User's Manual
Deployment Guide 145
HIVEOS CONFIGURATION FILE TYPES
HIVEOS CONFIGURATION FILE TYPES
HiveOS supports several types of configuration files: running, current, backup, bootstrap, default, and failed.
The running configuration (config) is the configuration that is actively running in DRAM. During the bootup process,
a HiveAP loads the running config from one of up to four config files stored in flash memory:
• current: a flash file containing a combination of default and admin-defined settings. During the bootup process,
this is the first config that the HiveAP attempts to load as the running config. This is also the file to which you
typically save commands from the running config (you can also save them to the bootstrap config). See Figure3.
• backup: a flash file that the HiveAP attempts to load during the reboot process if there is a newly uploaded
current config file or if it cannot load the current config file. See Figure4 on page146 and Figure5 on
page146.
• bootstrap: a flash file containing a second config composed of a combination of default and admin-defined
settings. The HiveAP fails over to this config when you enter the reset config command or if both the
current and backup config files fail to load. See Figure6 on page148.
• default: a flash file containing only default settings. If there is no bootstrap config, the HiveAP reverts to this
config when you enter the reset config command or if both the current and backup config files fail to load.
See Figure6 on page148.
When using the CLI, the two most frequently accessed config types are the running config and current config. When
you enter a command in the running config, the HiveAP performs it immediately. However, because the running
config is stored in volatile memory (DRAM), the commands are not yet permanent and will be lost when the HiveAP
next reboots. For your configuration settings to persist after rebooting, enter the save config command. This
command saves the running config to the current config, which is a file stored in nonvolatile (flash) memory. See
Figure3.
Figure 3 Relationship between Running and Current Config Files
Note: There is also a failed config file, which holds any backup config that fails to load. See Figure5 on
page146.
øÒ±¬»æ ̸» ½±³³¿²¼- ·² ¾±´¼ ¸¿ª» ²±¬ §»¬ ¾»»² -¿ª»¼ô
©¸·½¸ ·- ©¸§ ¬¸»§ ¼± ²±¬ ¿°°»¿® ·² ¬¸» ½«®®»²¬ ½±²º·¹ò÷
Ý«®®»²¬ ݱ²º·¹
ø·² º´¿-¸ ³»³±®§÷
Ϋ²²·²¹ ݱ²º·¹
ø·² ÜÎßÓ÷
̸» ®«²²·²¹ ½±²º·¹ ½±³°®·-»- ¬¸» ½«®®»²¬ ½±²º·¹
°´«- ¿²§ ½±³³¿²¼- ¬¸¿¬ ¸¿ª» ²±¬ §»¬ ¾»»²
-¿ª»¼ò̸» ®«²²·²¹ ½±²º·¹ ®«²- ·² ÜÎßÓò
̸» ½«®®»²¬ ½±²º·¹ ½±³°®·-»- -¿ª»¼
½±³³¿²¼- °´«- ¼»º¿«´¬ -»¬¬·²¹-ò ̸»
½«®®»²¬ ½±²º·¹ ·- -¬±®»¼ ·² º´¿-¸ ³»³±®§ò
Ϋ²²·²¹ ݱ²º·¹
Ò»© Ý«®®»²¬ ݱ²º·¹
Ю»ª·±«- Ý«®®»²¬ ݱ²º·¹
ø±ª»®©®·¬¬»²÷
ɸ»² §±« »²¬»® ¬¸» -¿ª» ½±²º·¹ ½±³³¿²¼ô
¬¸» Ø·ª»ßÐ -¿ª»- ¬¸» ®«²²·²¹ ½±²º·¹ º®±³
ÜÎßÓ ¬± º´¿-¸ ³»³±®§ô ©¸»®» ·¬ ¾»½±³»-
¬¸» ²»© ½«®®»²¬ ½±²º·¹ô ®»°´¿½·²¹ ¬¸» ±²»
°®»ª·±«-´§ ¬¸»®»ò
-¿ª» ½±²º·¹
øÒ±¬»æ ߺ¬»® »²¬»®·²¹ ¬¸» -¿ª»
½±²º·¹ ½±³³¿²¼ô ¬¸» ½«®®»²¬ ¿²¼
®«²²·²¹ ½±²º·¹- ¾»½±³» ·¼»²¬·½¿´ò÷