Specifications

VE106 Groove-N-Go Tool 33
ROLL GROOVE SPECIFICATIONS COPPER TUBING TO CTS US STANDARD – ASTM B-88 AND ASTM B-306
Copper Tubing
Size Dimensions – inches/millimeters
Groove Depth
“D”
(Ref. Only)
Min. Allow.
Wall Thick.
“T”
Max. Allow.
Flare Dia.
“F”
Nominal inches
(Actual mm)
Copper Tubing Outside
Diameter ‡ Gasket Seat “A” Groove Width “B” Groove Diameter “C”
Max. Min. Basic Max. Min. Max. Min. Max. Min.
2 2.127 2.123 0.610 0.640 0.580 0.330 0.300 2.029 2.009 0.048
DWV*
2.220
54,0 54,0 53,9 15,5 16,3 14,7 8,4 7,6 51,5 51,0 1,2 56,4
2
1
/
2
2.627 2.623 0.610 0.640 0.580 0.330 0.300 2.525 2.505 0.050 0.065 2.720
66,7 66,7 66,6 15,5 16,3 14,7 8,4 7,6 64,1 63,6 1,2 1,7 69,1
3 3.127 3.123 0.610 0.640 0.580 0.330 0.300 3.025 3.005 0.050
DWV*
3.220
79,4 79,4 79,3 15,5 16,3 14,7 8,4 7,6 76,8 76,3 1,2 81,8
4 4.127 4.123 0.610 0.640 0.580 0.330 0.300 4.019 3.999 0.053
DWV*
4.220
104,8 104,8 104,7 15,5 16,3 14,7 8,4 7,6 102,1 101,6 1,4 107,2
5 5.127 5.123 0.610 0.640 0.580 0.330 0.300 4.999 4.979 0.063
DWV*
5.220
130,2 130,2 130,1 15,5 16,3 14,7 8,4 7,6 127,0 126,5 1,6 132,6
6 6.127 6.123 0.610 0.640 0.580 0.330 0.300 5.999 5.979 0.063
DWV*
6.220
155,6 155,6 155,5 15,5 16,3 14,7 8,4 7,6 152,3 151,9 1,6 158,0
8 8.127 8.121 0.610 0.640 0.580 0.330 0.300 7.959 7.939 0.083
DWV*
8.220
206,4 206,4 206,3 15,5 16,3 14,7 8,4 7,6 202,2 201,7 2,1 208,8
‡ The outside diameter of roll grooved copper tubing cannot vary from the tolerance listed. The maximum allowable tolerance from square cut ends is 0.030 inch (0,8 mm) for 2 – 3-inch (54,0 – 79,4-mm) sizes and 0.045 inch (1,1 mm) for 4 – 6-inch (104,8 – 155,6-mm) sizes; this is measured from the true square line. * ASTM B-306 drain-waste and vent (DWV) is the minimum wall thickness of copper tubing that can be roll grooved.
TM-VE106 3736 Rev_B.fm Page 33 Monday, May 9, 2005 12:02 PM