Installation Sheet

ManualsBrandsAccess Lighting ManualsCeiling FixturesAccess Lighting Vision 2 Light Flush Mount Ceiling Fixture

CERTIFICATION: cULus DAMP

NO. 50030, 50031, 50032, 50033, 50034, 50035

INSTALLATION INSTRUCTIONS

IMPORTANT

Before assembling your ACCESS LIGHTING fixture, please make sure that

you carefully read through this instruction sheet. Save these instructions

and refer to them when additions to or changes in the fixture

configuration are made.

CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH

CIRCUIT CONDUCTOR.

CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES

CONDUCTEURS DE LA DERIVATION SONT ADEQUATS

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION

AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,

PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT

AINSI QUE LES RISQUES INHERENTS

NOTE: The important safeguards and instructions that appear in this

manual are not meant to cover all possible conditions and situations

COLLECTION

APPLICATION MODEL NO.

that may occur. It must be understood that common sense, caution and

care, are factors that can’t be built into any product. These factors must

be supplied by the person(s) caring for and operating the fixture.

GENERAL INFORMATION

All electrical connections must be in accordance with all ordinances,

Local and National Electrical Codes. These fixtures are intended for

mounting to a standard 4” x 2 1/2”metal octagon outlet box. The box

must be directly supported by the building structure and U.L. Recognized.

STEP BY STEP INSTRUCTIONS

Vision

WHAT WE

PROVIDE

•

Crossbar

• Mounting

Hardware

• Canopy with

Sockets

• 1 x Glass

Shade

Ceiling

50032

WHAT YOU NEED

• Philips Screwdriver

• Wire Cutters

• Wiring Supplies as

Specified by Electrical Code

Before starting your installation disconnect the Power by turning off the

Circuit Breaker or by removing the fuse at the fuse box. Just turning the

light off at the light switch is not sufficient to prevent electrical shock.

• 1 x R7s Base

Bulb

(Model dependent)

Model 50030/31: 1 x 200W

Model 50032: 2 x 150W

Model 50033/34: 1 x 150W

Model 50035: 2 x 150W

PREPARE FIXTURE

If there is an existing fixture remove

it.

Expose the supply wires from the outlet

Secure the crossbar to the J-box with the supplied

scre

Summary of content (3 pages)

PAGE 1
NO. 50030, 50031, 50032, 50033, 50034, 50035 CERTIFICATION: cULus DAMP INSTALLATION INSTRUCTIONS IMPORTANT Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. Save these instructions and refer to them when additions to or changes in the fixture configuration are made. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
PAGE 2
NO. 50030, 50031, 50032, 50033, 50034, 50035 CERTIFICATION: cULus DAMP 2 CONNECT THE WIRES Gently pull the supply wires through the hole in the crossbar. Connect the black supply wire to the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts. Either wrap the green wire around one of the protruding screws or connect it to the supply ground wire. Secure all wires with U.L.
PAGE 3
NO. 50030, 50031, 50032, 50033, 50034, 50035 CERTIFICATION: cULus DAMP 5 6 SECURE GLASS SHADE Hold the glass shade up to the canopy and secure with the supplied screw knobs. RESTORE THE ELECTRICITYAND CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING FIXTURE CAUTION Please ensure that the fitting is cool and switched off before replacing the bulb.DO NOT use bulbs that might exceed the maximum wattage, stated on caution label.