Operating instructions

ManualsBrandsAcard ManualsComputer AccessoriesACP-2200

Notification

Notification is hereby given that TransTel Communications Inc. reserves the right to modify, change, update or

revise this document from time to time as required without the prior obligation to notify any person, company or

organization. Further, TransTel makes no warranty or representation, either expressed or implied, with respect to

merchantability, or fitness of its products for a particular purpose.

This document or any parts thereof are not to be reproduced or transmitted in any form or by any means, electronic

or mechanical, including photocopying, recording, or information storage and retrieval systems for any purpose

whatsoever without the express written permission of TransTel Communications Inc.

Summary of content (195 pages)

PAGE 1
Notification Notification is hereby given that TransTel Communications Inc. reserves the right to modify, change, update or revise this document from time to time as required without the prior obligation to notify any person, company or organization. Further, TransTel makes no warranty or representation, either expressed or implied, with respect to merchantability, or fitness of its products for a particular purpose.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS Installation Safety Precautions: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. The TransTel TD-824-I utilizes a 3-prong grounding power supply cord.
PAGE 3
PAGE 4
TransTel Model TD-824-I Digital Telephone System General Description - Installation - Programming Forms Manual Table of Contents Notification..........................................................................................................................................................................1 General Description - Introduction ..................................................................................................................................10 FCC Rules and Regulation.......
PAGE 5
TransTel Model TD-824-I Digital Telephone System – Table Of Contents Installing expansion and optional cards...................................................................................................................... 23 TD-CFC - Conference Card.................................................................................................................................... 24 TD-MSC - Multi Service Card .............................................................................................
PAGE 6
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-14 - System Parameters Form – Miscellaneous .........................................................................................70 G1-10a6 Form 06-01 - Relay Assignment Form: .............................................................................................................71 G1-10a6 Form 06-st – ACP/Doorphone Relay Assignment Form: ........................................
PAGE 7
TransTel Model TD-824-I Digital Telephone System – Table Of Contents Form 74 - Least Cost Routing - Digit String Analysis Table: ................................................................................... 136 Form 74 - Least Cost Routing - Digit String Analysis Table: ................................................................................... 137 Form 76 - Least Cost Routing - Routing Table Normal Operation: .......................................................................
PAGE 8
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Answering Calls......................................................................................................................................................170 Answering a Doorphone.........................................................................................................................................171 Answer Paging (Meet Me Page) ......................................
PAGE 9
TransTel Model TD-824-I Digital Telephone System – Table Of Contents Voice Mail Message Retrieval ............................................................................................................................... 190 Voice Mail Transfer Key......................................................................................................................................... 190 Volume Control......................................................................................................
PAGE 10
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual General Description - Introduction ® The General Description section contains an easy to understand overview of the TransTel TD-824i Digital Telephone System.
PAGE 11
TransTel Model TD-824-I Digital Telephone System – General Description Compatibility of the Telephone Network and Terminal Equipment. (a) Availability of telephone interface information.
PAGE 12
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Description The TD-824i is an advanced digital telephone system employing a microprocessor stored program and digitally controlled solid state time-division switching. The TD-824i system is specifically designed for small business as well as residential applications.
PAGE 13
TransTel Model TD-824-I Digital Telephone System – General Description Easy Maintenance • Solid-state design minimizes trouble and eliminates periodic maintenance. • Easy Expansion. Various Interface Cards for simple, modular expansion. • Versatile programming and options for ease of selection. • Database Battery Back Up - Customer data is backed up when the power is turned off and back on. Batteries can periodically be replaced with power on using commercially available replacements.
PAGE 14
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual TransTel Telephone Model DK-1/D TransTel Telephone Model DK-3/D TransTel Telephone DK-2 (shown with optional 66 button DK-2DSS console) The DK-2 expands the LCD display to a 4 line indication, providing an enhanced view ot call progress and adding the ability to utilize the 4 “Softkeys” Page 14 Version 1.
PAGE 15
TransTel Model TD-824-I Digital Telephone System – General Description System Specifications System Capacities / Maximum CO/PABX Lines Key Telephones / ACP / Digital Doorphones (Maximum) Single Line Phones(Maximum) Control Relay 8 24 8 1 per cabinet 1 per ACP or Digital Doorphone 1 per cabinet 1 per ACP or Digital Doorphone External Input Sensor Intercom Paths (Local) Doorphone 1 analog (requires single line card) < 24 Digital doorphones 1 Total 600 sets for Private/System Speed Dial.
PAGE 16
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual MAXIMUM LOOP RESISTANCE/IMPEDANCE Digital Key Telephone Less than 40 ohms 26 AWG / 650 feet (200 meters) Single Line telephone Less than 800 ohms 22 AWG / 2,620 feet (800 meters) Doorphone Less than 40 ohms Music Source Input Impedance 600 ohms Maximum Input 0.
PAGE 17
TransTel Model TD-824-I Digital Telephone System – General Description Features System Features 1A2 Emulation Attendant Console Assigment (4) Consoles Account Code Capability Attendant Overflow Automatic Line Access Automatic Line Search Automatic Ring-down Automatic Wake-up Battery Charger Behind PABX Operation Centrex Operation Class Of Service (10) Classes CO Line Groups CO Line Hunting CO Line Name Programming CO Line Ring Types Linear Common Audible Circular Add on Ring Day/Night Service Manual/Automa
PAGE 18
Station Features Advisory Messages System Personal Access to System Programming from any station Account Code Capability Auto Hold Auto Hold Recall Automatic Call Back Automatic Answer-Intercom Automatic Line Access Automatic Redial Automatic Volume Increase Brokers Call (Split/Swap) Call Duration Timer (LCD Phones) Call Waiting Call Forwarding All Calls Busy No Answer Busy / No Answer External Call Pickup Call Split Call Transfer Calling Name Display (LCD Phones) Calling Number Display (LCD Phones) Camp On
PAGE 19
TransTel Model TD-824-I Digital Telephone System – General Description Parts & Peripherals System Modules Model TD-824i TD-TKU-4 TD-CID/FSK TD-SIU-2 TD-SIU-3 TD-DKC-8 TD-SLC-8 TD-SLC-2 TD-RGU Description KSU with 4 CO lines, 4 Digital twin ports Trunk Card : 4 CO lines Caller ID daughterboard. Installs on TD-TKU-4. Converts 4 lines for Caller ID Features. FSK Format (U.S.
PAGE 20
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Optional Interface Cards Model TD-VSC TD-MSC TD-CFC Description Voice Service Card (60 sec. / 8 voice segments)- Auto Attendant, Wake-up, Message Waiting RS232/Relay/Sensor/External Paging Interface Conference / Expansion Card – 32 parties conference / Expand system from 6 x 16 to 8 x 24 Associated Software Model TD-RPS Page 20 Description Remote Programming Software Version 1.
PAGE 21
TransTel Model TD-824-I Digital Telephone System – System Installation System Installation - Introduction This section provides directions for installing the system and optional equipment. The installation must be performed by qualified service personnel.
PAGE 22
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Site Requirements Location Choosing The Right Environment • System should be installed in a clean, dry, secure location. This location must have adequate ventilation, and a temperature from 0ºC to 45ºC (32ºF to 113ºF), with 10% to 95% non-condensing relative humidity. DO NOT install the equipment near sources of static electricity, excessive vibration, or water. Avoid direct sunlight.
PAGE 23
TransTel Model TD-824-I Digital Telephone System – System Installation Installation Caution 1. This system should be installed only by qualified service personnel. 2. Do not install the Power Supply unless you have read the following instructions and completed all the installation and wiring. 3. STATIC SENSITIVE DEVICES! Please handle with care. Installing expansion and optional cards In this step you will be installing printed circuit cards on to header pins of the main board in the basic cabinet.
PAGE 24
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Installing expansion and option cards (continued) TD-CFC - Conference Card Install this card on CN6 of the TD-MBU. Be sure that the component side of the TD-CFC is facing in towards right of KSU. CFC card is necessary to expand the system from 6 x16 to 8x 24. TD-MSC - Multi Service Card Align CN1 of the MSC card with CN4 of the TD-MBU.
PAGE 25
TransTel Model TD-824-I Digital Telephone System – System Installation TD-TKU - 4 Port CO Line Card Align four holes of TD-TKU with the standoffs on top of the existing TD-TKU or TD-SIU card provided for in the basic key service unit. Once aligned, place the four screws into the standoff securing the TD-TKU card. Verify that the TD-TKU that was installed in the basic KSU has JP1 set to the ‘TKU1’ position.. Set JP1 on the new installed TD-TKU to ‘TKU2’.
PAGE 26
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual TD-STC - Digital Station Expansion Card TD-STC – Digital Station Expansion Card st For the 1 TD-STC card: This expands KSU from 8 to 16 stations. Set JP1 on TD-STC to ‘STC1’ position. Align CN2 of the TD1-STC card with CN2 f the TD-MBU. Align four screw holes on TD-STC with the standoff. Once aligned push the TD-STC on the connector. Place the screw into the standoff securing the TD-STC card.
PAGE 27
TransTel Model TD-824-I Digital Telephone System – System Installation TD-SLC - Single Line Station Adapter Card Install G1-SLC on TD-MBU: Connect the attached cable between CN1 of TD-SLC card to CN7 of the TD-MBU. Align four screw holes on the TD-SLC with the standoffs. Place the screws into the standoffs securing the TD-SLC card. Connect the attached cable between CN3 of TD-SLC to CN4 of TD-TKU for power fail transfer.
PAGE 28
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Voltage Selection Check Make a check to assure the power supply jumper setting is for the proper voltage. When complete, place the power supply cover back on the power supply. Replace Cover With the expansion and option cards installed and the battery insulator removed, replace the cover and install the 4 screws removed earlier.
PAGE 29
TransTel Model TD-824-I Digital Telephone System – System Installation Preparing The External Battery Backup The Key Service Unit can have two external backup batteries in series (12 volts each) for emergency power and when a power failure takes place. If you are installing an optional Battery Backup (SK-BCAB/B), make certain that there is adequate room for its installation.
PAGE 30
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual System Ground It is strongly recommended that the system be grounded by connecting a heavy, insulated copper wire (e.g., 14AWG or larger) between the grounding bolt on the right-lower side of the cabinet and an earth ground. Do not connect the grounding wire of the KSU to a computer, telex, or any other external device.
PAGE 31
TransTel Model TD-824-I Digital Telephone System – System Installation CAUTION!: Avoid shorting Tip and Ring together. It may damage the TD-MBU or TD-STC board. • Connections to telephones are made pins 2 & 3 and pins 1 & 4. • A cable cover is provided with the KSU. Station cables can enter from either the top or bottom as desired. Remove one or both ends of the cover as required and route the station cable through the hole. Terminate the station wires with the connectors that are provided.
PAGE 32
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Access Control Phone (ACP) and Digital Doorphone Unit (DDU) • • • Page 32 Single Pair Wiring is required for connection to ACP/DDU phone. ACP/DDU Phone can be used on a digital pair with another ACP/DDU or a DK-1 telephone set. st nd ACP/DDU can be either 1 or 2 station on circuit. Version 1.
PAGE 33
TransTel Model TD-824-I Digital Telephone System – System Installation Single Line Telephone Connections to telephones are made pins 2 & 3 (odd ports) and pins 1 & 4 (even ports). A cable cover is provided with the KSU. Station cables can enter from either the top or bottom as desired. Remove one or both ends of the cover as required and route the station cable through the hole. Terminate the station wires with the connectors that are provided.
PAGE 34
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Analog Door Phone Connection One Door phone may be connected to the TD-824 system and only with SLC-8 cards.. A cable cover is provided with the KSU. Door phone cable can enter from either the top or bottom as desired. Remove one or both ends of the cover as required and route the door phone cable through the hole. Terminate the door phone wires with the connectors that are provided.
PAGE 35
TransTel Model TD-824-I Digital Telephone System – System Installation CO/PABX Connections Make your CO line connection to the telephone company on this connector. Pins 3 and 4 of the connector are for the CO line. RJ-11C (2 wire) modular connector is required. 2-conductor wiring is required. Optional Cabling Connect a 6 conductor mounting cord from the KSU to a RJ-25 modular block. Door Switch (Relay) Connection One Door Switch (24+-12VDC) may be used on the G1-824 system. 2-conductor wiring is required.
PAGE 36
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Music on Hold Connection • • Connect the (optional) external music source to the external Music" input labeled on the KSU. Use a 1/8” mini plug to connect the music source to the KSU. RS232 Port Connection Use the RJ-11 connector to terminate the RS232 cable. Then connect the RJ-11 to the KSU with a 6 conductor line cord. Insert the line cord into the connector labeled RS-232.
PAGE 37
TransTel Model TD-824-I Digital Telephone System – System Installation Power On and Operational Test Before connecting the TD-PWU to AC power: • Verify that input voltage and input voltage selection jumper on TD-PWU are correct before you power up the system. • Plug the power cord into a power outlet. • Verify the system boots properly by checking the display of a telephone set. • You may now connect the battery back up unit if applicable.
PAGE 38
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Series Model TD-824i - Programming Forms Manual Programming Information This document contains the system forms required to program the TD-824i and an explanation of the parameters. New Systems We recommend that all new systems have the system memory reset before system programming takes place.
PAGE 39
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Basic Programming Commands: For the first time or infrequent installer, a programming overlay is provided with each Key Service Unit. This overlay, when placed on a TransTel LCD telephone set indicates keys used during programming for easy reference. Experienced installers may program without the overlay. Both key designations are listed below. Note: Keys listed between [ ] indicate the default keys shown on a telephone set.
PAGE 40
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Alphanumeric Entry: The following table indicates the capabilities of the name programming functions if they are selected on the system. System Speed Dial, Personal Speed Dial, Stations, CO Lines and Sensors may be programmed with names.
PAGE 41
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 01 - Day Ringing and Ringing Line Preference Assignment Ring Type : Linear / Circular / Hunt / Private / Common (See Form 35-CO-07) (Line 1) 01-01- 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 Extension (Line 2) 01-02- 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 01 02 03
PAGE 42
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 02 - Night Ringing and Ringing Line Preference Assignment Ring Type : Linear / Circular / Hunt / Private / Common (See Form 35-CO-08) (Line 1) 02-01- 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 Extension (Line 2) 02-02- 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 01 02 03 04 05 06 07 08 09
PAGE 43
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 03 - Door Phone Ringing Assignment Form 03 – 01 - 01 02 03 04 05 06 07 08 Extension General: This program assigns the door phone to ring the programmed stations. If the only entry on form 03-01-01 is 99, then all phones will ring. Description: 1. There is one door phone port available in the TD-824i. 2. Eight stations can be assigned to ring for the door phone. 3. To clear all entries press [REDIAL]. 4.
PAGE 44
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 04 - Console Assignment Form Console Group 01 04 – 01 - 01 Console Group 02 03 04 04 – 02 - Extension Console Group 04 – 03 - 04 – 05 - 03 01 Console Group 02 03 04 04 – 04 - 04 – 07 - 02 03 04 02 03 04 02 03 04 02 03 04 04 01 Extension 05 01 Console Group 02 03 04 04 – 06 - Extension Console Group 01 Extension Extension Console Group 02 06 01 Extension
PAGE 45
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-01 - System Parameters Form - Timers-1 G1-a20m G1-a20t 01 02 03 04 05 06 07 08 0-9 0-9 0-9 0-9 0-9 0-9 0-9 0-9 1 1 1 1 4 2 2 1 Form 05-01Range of Entries Default Value Item 05-01-01 05-01-02 05-01-03 05-01-04 05-01-05 05-01-06 05-01-07 05-01-08 Valid Settings 0-9 0-9 0-9 0-9 0-9 0-9 0-9 0-9 Description Default Hold Recall Time Exclusive Hold Recall Time Hold Recall Timeout G1-a20m DISA Access D
PAGE 46
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual G1-a20m 05-01-04. DISA Access Delay Day Service: This parameter sets the time duration that a DISA trunk will ring prior to connection to return dial tone or VSC message. (Stations can answer during this time.) 0 = Automatic connection, no ring to the stations. 1-8 = Automatic connection after 2-254 seconds ringing as listed below.
PAGE 47
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-02 - System Parameters Form - Timers-2 Form 05-02- 01 02 03 04 05 06 07 08 0-9 0-9 0-9 0-9 0-9 0-9 0-9 0-9 5 5 1 8 4 3 2 6 Item Range Of Entries Default 05-02-01. SLT Dial Tone Timeout: This parameter is for Single Line Telephones. If a key is not pressed before the assigned time period expires when Dial Tone is given, a Busy Tone will be heard and the DTMF receiver will be released. 05-02-02.
PAGE 48
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 02-05 Continued 05-02 05 - Key Telephone Flash Timer (ms. = milliseconds): This parameter permits the selection of Flash time for Key stations when pressing the [TRF/FL] key or an analog phone which presses flash and then dials 800 while connected to an outside line. After dialing 800 the flash signal will be sent to the CO line and the analog phone will reconnect to the line 0=80 ms.
PAGE 49
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-03 - System Parameters Form - Codes-1 Form 05-03- 01 02 03 04 05 06 07 08 0-1 0-1 0-1 0-9 0-9 2-4 0-1 0-9 1 0 0 9 0 2 0 9 Code Range Of Entries Default 05-03-01 - Pulse Dial - Make / Break Ratio Dial Pulse Ratio: This permits the selection of a Make/Break Ratio for Dial Pulse signaling 0=33/67 1=40/60 05-03 02 - Automatic CO Line Search During Speed Dial, Auto Redial, Saved Redial, etc: This allow
PAGE 50
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-03 Continued 05-03-06 - Station Number Digit Length: This assigns the number of digits used for the station numbering plan. 2, 3, or 4 digits may be used.
PAGE 51
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-04 - System Parameters Form - Codes-2 Form 05-04- G1-a20u 01 02 03 04 05 06 07 08 Range of Entries 0 0-1 0-1 0 0-4 0-1 1-2 Default 1 1 0-2 5-7 0 0 0 1 0 1 Item 05-04-01 – RS-232 Baud rate: This paramter controls the output speed of data from the system.
PAGE 52
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 05-04-06 - Speed Dial Distribution: This parameter sets the number of speed dial numbers allocated to the system speed dial. Adding extra numbers to system Speed Dial reduces the number of personal Speed Dial numbers available to share between individual stations Numbers after backslash indicate sets available with name feature enabled.
PAGE 53
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-05 - System Parameters Form - Codes-3 Form 05-05- 01 02 03 04 05 06 07 08 0-1 0 0-6 0-9 0 1 0-9 0-9 1 0 0 0 0 1 1 0 Item Range of Entries Default 05-05-01 – Wake Up Call Signaling: This parameter is for the Hotel/Motel environment to decide what an extension will hear upon receiving a wake up call.
PAGE 54
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-05 Continued 05-05-05 - Name Function: This parameter enables the naming feature for trunks, extensions and speed dials. Features \ Values 0 Display Name instead of number for Extension 1 2 X Directory Dial for Speed Dial X Directory Dial for Extension 3 5 7 X X X X X X X X: The feature is enabled.
PAGE 55
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-06 - System Parameters Form - Timer/Codes Form 05-06- 01 02 03 04 05 06 07 08 0-9 0-9 0 0-1 0-1 0-9 0, 1, 3 0 4 4 0 1 0 3 0 0 Item Range Of Entries Default 05-06-01 - Transfer Recall Timeout-Busy (seconds): This parameter sets the time duration between transferring a call to a busy party and automatic transfer back to the transferring party when the called party remains busy 0=5 1=10 2=15 3=20 4=30
PAGE 56
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-06 Continued 05-06-06 -CO Disconnect Timer for ECF, Unsupervised Conference, and DISA: This parameter sets the time that the system will allow an Unsupervised Conference or External Call Forward to continue before sending a warning tone to the parties and then disconnecting the call.
PAGE 57
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-07 - System Parameters Form - Timer/Codes Form 05-07- G1-a20u 01 02 03 04 05 06 07 08 0-1 0-1 0 0-1 0-7 0-9 0 0 0 0 0 0 0 0 0 0 Item Range of Entries Default 05-07-01 - Intercom Step Call: If setting is enable, when calling an internal station which is busy or does not answer, pressing [4] will call the station on the next port which is in the same station group as the called station.
PAGE 58
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 05-07- 04 - DISA Operator Recall Capability (No Digits Dialed): Setting No dialing after the first voice announcement from the VSU. 0= 1= 2= 3= 4= 5= 6= 7= * T The VSU has already announced the invalid number or a dialed number that has not been received completely.
PAGE 59
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-08 - System Parameters Form - Timer/Codes Form 05-08-T 01 02 03 04 05 06 07 08 0-9 0-1 0-9 0-1 0-8 0-9 0-9 0 5 0 0 0 7 1 7 0 Item Range of Entries Default 05-08-01 – Ring Hunt Interval (seconds): If setting is n, Then when an incoming call rings the first ring assigned extension and that extension is nd busy, after n seconds the call will ring the second of the ring assigned extensions.
PAGE 60
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-08 Continued 05-08-05 - SLT Feature Programming Access Code First Digit: This feature changes the programming digit used by an Analogue phone to perform its programmable features. For example call forward is normally 701, If this parameter is set to 3 the call forward code will be 301. If the setting is 0 then the analogue phones cannot do programming.
PAGE 61
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-09 - System Parameters Form - Misc. Form 05-09-T G1-a10ax 01 02 03 04 05 06 07 08 Range of Entries 0 0-1 0-9 0 0 0 0 0 Default 0 1 0 0 0 0 0 0 ITem 05-09-01 Reserved: 05-09-02 – Console Automatic Queuing: This feature enables the busy console(s) to have an intercom call(s) queued to it(them).
PAGE 62
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-09 Continued 05-09-06 - UCD Enable Time: This parameter is to set the time duration before the system answers an incoming call when the ring assigned station(s) are busy, if a VSC card is installed. The incoming call will show as a normal ring signal on the DSS key and can be answered by the operator at any time even while the voice message is playing to the caller.
PAGE 63
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-10 - Voice Mail Leading Digits Form 05-10-T G1-A10n G1-A20o 01 02 03 04 05 06 07 08 d d d d d d d d Range of Entries Default Description This parameter allows the system to insert digits before the call forwarded station number when the call forward is received by the voice mail port if Standard Protocol is selected.
PAGE 64
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual If the Incoming trunk indentifier is enabled in the TD-824i on Form 05-12-05 the dial string will be 7+ a two digit trunk number, so an identifier for trunk 1 will be 701, trunk 2 is 702 and so on. Answer Digit When a called station answers the System will play [DTMF A] to the voice mail port. Busy Digit. When a called station is busy the system will play [DTMF B] to the voice mail port.
PAGE 65
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual G1-a10ao Form 05-11 - System Parameters Form – Supplemental Form 05-11-T 01 02 03 04 05 06 07 08 Range Of Entries 0 0 0 0 0-3 0-9 0-9 0-8 Default 0 0 0 0 0 0 1 0 Item G1-a10a0 05-11-01 – Caller ID Ignore Header Digit: This option is enabled for locations where a non-numeric character precedes the Caller ID information. The non-mumeric character is not displayed on LCD displays.
PAGE 66
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 05-11-05 - DISA Digit Acceptance: This parameter sets which of the system functions are accessible by DISA callers 0=All special digits allowed 1=[*],[#] Allowed - [8],[9] Disallowed 2=[8],[9] Allowed - [*],[#] Disallowed 3=No Special Digits Allowed 05-11-06 - DISA Transfer Count: This function sets the number of times that an unsuccessful DISA call will attempt to retry a station and or trans
PAGE 67
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-12 - System Parameters Form - Miscellaneous Form 05-12-T G1-a10h G1-a20u 01 02 03 04 05 06 07 08 Range Of Entries 0 0 0-1 0-4 0-1 0 0 0 Default 0 0 0 4 0 0 0 0 Item G1-a20u 05-12-01 – TRF/FL Key Operation: If set to 0, transfer procedure requires that the TRF/FL 0=TRF/FL is pressed to transfer a call to a station.
PAGE 68
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 05-12-06 Trunk Group Access Type: If this parameter is set to 0 then line selection will be the first available trunk in the users dial (9-0) group. If the parameter is set to 1 then the lines will be selected in a Circular fashion till all lines have been used and then the selection will start again.
PAGE 69
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 05-13 - System Parameters Form - Miscellaneous Form 05-13-T G1-a10aw 01 02 03 04 05 06 07 08 Range Of Entries 0 0 0-1 0-4 0-1 0 0 0 Default 1 0 0 1 0 0 0 0 Item 05-13-01. Intercom Hot Key Dialing: This parameter when enabled allows stations to dial an intercom call On Hook without having to lift the handset or press the SPK key.
PAGE 70
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 05-14 - System Parameters Form – Miscellaneous Form 05-14-T 01 02 03 04 05 06 07 08 0-8 0 0 0 -1 0-9 0 0 0 0 0 0 1 0 0 0 0 Item Range Of Entries Default 05-14-01 – ISDN PLL Maintenance: This parameter controls the function of the internal phase locked loop, used for ISDN trunking.
PAGE 71
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual G1-10a6 Form 06-01 - Relay Assignment Form: TD-MSC card has 1 dry contact relay. No voltage is provided by the system, the installer will have to provide their own source to suit the application. Only use the relays to switch 24V. They are only designed for low voltage control circuits. All Relays are Normally Open contacts and will close on activation of the function for which they have been programmed.
PAGE 72
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Page 72 Version 1.
PAGE 73
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual DK-2 Key Layout Note: Keys 1 through 29 are programmable.
PAGE 74
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual DK-3 Key Layout Note: Keys 31 – 32 are not currently usable on the TD-824i. Page 74 Version 1.
PAGE 75
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 07 - Flexible Key Group Assignment: 07 - Group 01 Key Function 07 - Group 02 Key Function Key Function Key 01 16 01 16 02 17 02 17 03 18 03 18 04 19 04 19 05 20 05 20 06 21 06 21 07 22 07 22 08 23 08 23 09 24 09 24 10 25 10 25 11 26 11 26 12 27 12 27 13 28 13 28 14 29 14 29 15 15 07 - Group 03 07 - Group 04 Key Function Key Function Key Function Key 01
PAGE 76
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 07 - Flexible Key Group Assignment: 07 - Group 05 Key Key Function Key Function Key 01 16 01 16 02 17 02 17 03 18 03 18 04 19 04 19 05 20 05 20 06 21 06 21 07 22 07 22 08 23 08 23 09 24 09 24 10 25 10 25 11 26 11 26 12 27 12 27 13 28 13 28 14 29 14 29 15 15 07 - Group 07 07 - Group 08 Key Function Key Function Key Functi
PAGE 77
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 07 Continued General: This program assigns 8 groups of Flexible key plans for Key phones. Each Key phone can be assigned to use two groups (Mode 41-st-(02 & 03)). Database Entry is as follows: 07-Gp-Key. For example: Form 07-01-01 Refers to Form 07 – Key Group 1 – Button 1. Form 07-01-29 Refers to Form 07 – Key Group 1 – Button 29. Description: Each key can be assigned as either a Trunk, a Station or a Function.
PAGE 78
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 08-01-IP - DSS Key Group Assignment: General: This program assigns 1 group of Flexible key plans for DSS Consoles. There is 1 key group available in the TD824i. Form 08-01 = DSS Key Group 1 The DSS Key Group to which a particular DSS console belongs is assigned on Form 43-port-03. Database Entry is as follows: 08 – 01 – Key Number.
PAGE 79
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 09 - System Speed Dial Assignment: Special Characters HOLD=Pause (p) Bin # 09- MSG=Tone (T) TRF/FL=Flash(F) MIC/AT = Change Key Toggles between Line entry, telephone number entry and name entry. TK: ## Number Name ____0 ____1 ____2 ____3 ____4 ____5 ____6 ____7 ____8 ____9 General: This program permits the assignment of up to 500 sets of system speed dialing codes.
PAGE 80
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 09 Continued i) Pause : During dial procedures, the dialing will wait for a programmable period (Refer Program 05-01-06). ii) Flash : This will make a loop disconnection of a pre-assigned duration. (Refer program mode 05-02-05). iii) Pulse to DTMF : If the dialed signal is "pulse", it will change to "DTMF". Note: Pressing {Don’t Care} will erase the digit which the cursor is on.
PAGE 81
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 10 - Single Digit Dialing Assignment : Form 10 - Single Digit Group 01 Item 01 02 Form 10 - Single Digit Group 02 03 04 05 Item 01 02 03 Station Station Form 10- Single Digit Group 03 Form 10- Single Digit Group 04 Item 01 02 03 04 05 Item 01 02 03 Station Station Form 10- Single Digit Group 05 Form 10- Single Digit Group 06 Item 01 02 03 04 05 Item 01 02 03 Station Station Form 10- Sing
PAGE 82
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 10 Continued Example 10-01-IP S.D.I. 11 13 22 00 55 In the above example an incoming DISA caller subject to Single Digit dialing group 01 who dials 1 will call station 11, dialing 2 will call station 13, 3 will call Station 22. Dialing 4 will allow the caller to dial the full extension number of any extension, which starts with 4, e.g. 44.
PAGE 83
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 12 - System Alarm Schedule: Schedule: Alarm Time (24 Hour Format 00:00-23:59) Duration (01-98 minutes) 01 02 03 04 05 06 07 08 09 10 General: This program permits the assignment of 10 time schedules for alarm clock purposes. Description: When the assigned time is reached, Background music will be broadcast over all Key telephones, which are idle. The time duration for alarm clock music is programmable (00 to 99 minutes.).
PAGE 84
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 13 - System Passwords: d(on't care) = DSS Key 4. All other digits are entered from the station keypad.
PAGE 85
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 14 - Station Message Detail Recording: Form 14 -01- 01 02 03 04 05 06 07 08 Options 0-9 0-1 0-1 0-1 0-1 00-99 0 0-1 Default 0 0 0 0 0 21 0 0 Item 14-01-01 - Recording Start Time: This parameter determines a “grace period” before call costing begins. This allows for calls that are made but unanswered.
PAGE 86
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 14 Continued 14-01-08 - Detect Polarity Reversal: If reversal is disabled, the system will start the call timer after accessing a CO line. If reversal is enabled, the system will start the call timer after the called party answers. 0= Not Detect P.R. / Normal SMDR format 1= Detect P.R. / Normal SMDR format output output 2= Not Detect P.R. / Simple SMDR format output 3= Detect P.R.
PAGE 87
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual CASE 6: October 2, 12:35 P.M., Station 116 made a call, which was restricted. CASE 7: Line 1 was used by station 121 for 55 seconds then put on hold. One meter pulse was recorded against this station for its section of the call. CASE 8: The held line 1 was answered by station 117 and he occupied the line for 3 minutes and 10 seconds. Four meter pulses were recorded against this station for its section of the call.
PAGE 88
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual SMDR OUTPUT DATA FORMAT - NEW With CLI Output ST.
PAGE 89
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 17 - Forced Account Code Assignment: Entries less than eight digits should have "d" in all trailing locations, (e.g., 123245ddd). ## Actual Code ## Actual Code ## Actual Code 01 17 33 02 18 34 03 19 35 04 20 36 05 21 37 06 22 38 07 23 39 08 24 40 09 25 41 10 26 42 11 27 43 12 28 44 13 29 45 14 30 46 15 31 47 16 32 48 General: This program creates 48 Forced Account codes.
PAGE 90
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 18 - Toll Plan Assignment: G1-a10aw 18-00 - ITem 01 02 03 04 05 06 07 08 09 10 18-01 - ITem 01 02 03 04 05 06 07 0-8 09 10 18-02 - ITem 01 02 03 04 05 06 07 08 09 10 18-03 - ITem 01 02 03 04 05 06 07 08 09 10 18-04 - ITem 01 02 03 04 05 06 07 08 09 19 18-05 - ITem 01 02 03 04 05 06 07 08 09 10 18-06 - ITem 01 02 03 04
PAGE 91
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 18 continued Toll Classes: Class 0 1 2 3 4 5 6 7 8 9 * d Function Unrestricted Use Form 51 for the Unrestricted numbers. Use Form 61 for the Restricted numbers Use Form 52 for the Unrestricted numbers. Use Form 62 for the Restricted numbers Use Form 53 for the Unrestricted numbers. Use Form 63 for the Restricted numbers Use Form 54 for the Unrestricted numbers.
PAGE 92
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 19 - Voice Service Unit Channel Assignment: Channel/Item Function Number Channel/Item 19-01 19-05 19-02 19-06 19-03 19-07 19-04 19-08 Function Number 19-01 - 19-08=Channel Assignments 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 18 Non-functional (Not Programmed) DISA: Day Main Answer Greeting DISA: Dialed Extension is Busy Message DISA: Dialed Extension does Not Answer DISA
PAGE 93
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual The 2 in brackets indicate that the second message segment is ready to record. Dial 0 and record the message to apologize for the continuing delay, VOICE PORT (1) RECORDING.............. When the message is recorded dial 1. Continue using the same procedure until all the required segments are recorded and then hang up. To record and play voice prompts: 1. From the operators station, dial 86 3.
PAGE 94
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 20 - Day/Lunch/Night Service Switching Schedule: This program assigns daytime from Sunday to Saturday for automatic night switching and sets lunchtime to allow the VSU to play a different message for this period. All times must be in 24 hour format.
PAGE 95
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 25 - Reset Data to System Default: This program resets all data to System Default. All new systems must be reset to default before any programming in case corruption has been caused during handling or shipping. When using item 3 or 4 these must be done AFTER the system reset is performed. General: This program resets all data to System Default.
PAGE 96
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 29 - CO Line Specifications #1: Line Data 01 02 03 04 05 06 07 08 Range 0 0-1 0 0-8 0-8 0-1 0-9 0-9 Default 0 1 0 0 6 0 0 0 29-01 Line 01 29-02 Line 02 29-03 Line 03 29-04 Line 04 29-05 Line 05 29-06 Line 06 29-07 Line 07 29-08 Line 08 29-xx-01-– CO Line Loop Receive Gain: This parameter allows adjustment of the system’s analog trunk interface to adapt to differ
PAGE 97
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 29-xx-05 – Incoming Call Connect: This feature allows either some or all stations which are ring assigned in Mode 01 or 02 to receive the audible ring signal when a trunk rings at the station.
PAGE 98
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 35 - CO Line Specifications: Line Data 01 02 03 04 05 06 07 08 Range 0-1 0-1 0-8 0-8 0-3 0-2 0-3 0-3 Default 0 1 0 0 3 0 0 0 Line 01 Line 02 Line 03 Line 04 Line 05 Line 06 Line 07 Line 08 35-xx-01 - Line Type: 0=CO Line (Connected to Telco Lines) 1=Behind PABX (Connected to a PABX Extension or Centrex line) 35-xx-02 - Dial Signaling Type: 0=Pulse Dialing 1=D
PAGE 99
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 35 Continued 35-xx-05 - Line Pick Up Enable (Allows a non-ringing station to answer an incoming call): Enable = An incoming call on this line can be answered by non-ringing stations. Disable = An incoming call on this line can not be answered by non-ringing stations.
PAGE 100
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 36 - CO Line Groups (Dial 9 Groups): Line - 01 02 03 04 05 06 07 08 36 01 36-02 36-03 36-04 36-05 36-06 36-07 36-08 General: This program permits each trunk line to be assigned to different Trunk groups. There are eight groups in total. This parameter will work with the following features: . Dial 9 (or 0) access to trunk group. .
PAGE 101
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 38 - Alternate CO Line Groups (Dial 87 Groups): This program permits each line to be assigned to different Trunk groups which can be accessed by dialing [87]. There are 8 groups in total. This group will be available to a station in addition to it's dial 9 group. Always set outgoing calls to start from the highest installed trunk and program in descending order to the lowest trunk equipped.
PAGE 102
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 39-00 - Sensor Assignment Form – KSU Sensor only: The SENSOR type may be normally open or normally closed and can be set to be activated in Day or Night switching or in both.
PAGE 103
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual G1-a10aq Form 39-st Sensor Assignment Form – ACP and Doorphone Units: The SENSOR type may be normally open or normally closed Form 39-st01 02 Name - (Reference Only – Not programmed in system) Form 39- Starting with software version G1-a10aq, the ability was added to the system to program the sensors that accompany each Digital Doorphone Unit and ACP. Valid settings are: 00=Can provide two different methods of operation.
PAGE 104
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 40 - Station Class of Service (Part 1): Item 40-st-01 40-st-02 40-st-03 40-st-04 40-st-05 40-st-06 40-st-07 40-st-08 Valid Settings 0-9,d 0-9 0-9 0-1 0-1 0-1 0-1 00-48 Description Override/OHCA Level Monitor Level Limit Call Duration Station Loud Bell Access Paging Receive Paging Security Code Status Forced Account Code Default 1=Low 1=Low 0=No 0=No 0=Yes 0=Yes 0=None 00=All 40-STN-01
PAGE 105
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 40-STN-07- Station Lock/Unlock Status: If a phone becomes locked accidentally or the user forgets their lock code, this parameter will unlock the phone. There is no way of finding what the lock code was. 0 = Station unlocked. (Can make outgoing calls.) 1 = Station locked. (Can not make outgoing calls.) 40-STN-08 - Forced Account Code: There are 48 forced account codes which can be used on the system.
PAGE 106
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 41 - Station Specifications Item 41-st-01 41-st-02 41-st-03 41-st-04 41-st-05 41-st-06 41-st-07 Valid Settings 1-8 1-8 1-8 1-8 0-9 0-9 cn Description Station Group / Agent Group for UCD Key Group For KeyPhone Shift Key Group For KeyPhone Dial 9 trunk group Toll plan - Day Toll plan - Night c = Card number, n = Port number Default 1=1 2=2 0=None 1=1 0=0 0=0 41-STN-01 – Group Assignment:
PAGE 107
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 41-STN-07 - Port Number: This is for checking only, the system will automatically show the correct port number. It is not possible for the user to change or remove this parameter. This parameter is not user programmable In the TD-824i, the port number consists of 2 digits 11~18: station ports on the G1-MBU st 21~28: station ports on the 1 G1-STC card. nd 31~38: station ports on the 2 G1-STC or G1-SLC card.
PAGE 108
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 42 - Personal Speed Dial Table Assignment: Default Numerical -01 DSS -02 Default 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- 42-___- Numerical -01 DSS -02 General: This program divides sets of Individual Speed Dial into blo
PAGE 109
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual If problems are encountered with stations not being able to program speed dial numbers, check this parameter to be sure that speed dial locations are available to the station. If the station card was installed at the time of system initialization then the blocks will have been allocated automatically. Default Information provides the basic two digit default numbering plan for the system.
PAGE 110
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 43 - Port Assignments: Station Card #1 (Ports 11 – 18) 01 02 03 04 Name (Optional) 03 04 Name (Optional) 03 04 Name (Optional) 43-1143-1243-1343-1443-1543-1643-1743-18Station Card #2 (Ports 21 – 28) 01 02 43-2143-2243-2343-2443-2543-2643-2743-28Station Card #3 (Ports 31 – 38) 01 02 43-3143-3243-3343-3443-3543-3643-3743-38- Form 43-port-01 – Station Extension Number: Any vali
PAGE 111
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 43-port-02 – Equipment Type: (Recognized by the system Automatically) 0=No Equipment Connected 1=Digital Telephone without LCD 2=Digital Telephone with LCD 3=Hybrid function for Digital Phone with SLT adapter installed 4=Single Line Telephone 5=DSS console 6=Reserved 7=SLT music port 8=Voice Mail Port 9=Reserved D=Doorphone Note: Equipment Type 8 (above) is the only item that can be programmed.
PAGE 112
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 44 - Station Class of Service (Part 2): Station Card #1 44-EXT-- G1-a10as 01 02 03 04 05 06 07 08 0 0 0 0 0 0 0 0 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 0 0 0 0 0 0 0 0 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ Default Station Card #2 44-EXT-44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-_____ 44-____
PAGE 113
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 44 continued 44-ext-01 – System Alarm Station: If disabled, the station will not receive system alarm clock signals 0=Enable 1=Disable 44-ext-02 – Call Hold: 0=Hold is allowed ( SLT Internal Flash) 1=Hold is not allowed (SLT devices can flash CO) 44-ext-03 – Call Split: If the setting is disable, the station will not be able to activate call splitting function.
PAGE 114
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 45 - Station Class of Service (Part 3): Station Card #1 45-STN-- 01 02 03 04 05 06 07 08 0 0 0 0 0 0 0 0 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ Default Station Card #2 45-STN-45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ 45-_____ Station Card #3 45-STN-45-_____
PAGE 115
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 45 Continued 45-ext-01 - Intercom Dialing Restriction: If this setting is enabled, the station can not make an intercom call by dialing a station number. Under this condition, the Key Phone still can press a Flexible Key to make an intercom call or the Key Station or Analogue phones can call a station using the "Single Digit" feature.
PAGE 116
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 46 - Station Class of Service (Part 4): Station Card #1 46-STN-- G1-a10av 01 02 03 04 05 06 07 08 0 1 0 0 0 1 2 0 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ Default Station Card #2 46-STN-46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ 46-_____ Station Card #3 46-STN
PAGE 117
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 46 continued 46-ext-01 - Dial 87 Line Group: If this setting is from 1 to 8, after the station dials [87], the system will automatically search for a free line which is assigned in group 1 to 8 in Program Form 38. 0=Disabled 1-8=Group Number 46-ext-02 - Message Waiting Level: The Stations assigned higher levels can leave message for stations with the same or lower levels.
PAGE 118
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 46-ext-05 - Maximum Transfer Times: This feature allows the user or the automatic attendant console to re-transfer the same call for the number of times set in this parameter.
PAGE 119
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 47 - Hot Line Table: STN SPD? (Y/N) Location (Number) STN SPD? (Y/N) Location (Number) This feature allows a user to lift the handset and directly call a specific outside party through System Speed Dial or an Intercom Extension without dialing any digits. * Pressing [SPK] on a Keyphone allows the Hot line to be over-ridden. Description: 1.
PAGE 120
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 50 - Station Class of Service (Part 5): Station Card #1 50-STN-- 01 02 03 04 05 06 07 08 0 1 0 0 0 1 2 0 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ Default Station Card #2 50-STN-50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ 50-_____ Station Card #3 50-STN-50-_____
PAGE 121
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 50-ext-01 – Digital Doorphone/ACP Intrusion Alarm: G1-a10ar When enabled, this parameter will cause an alarm condition on all stations if the ACP is disconnected or is opened. Dial [777] from a system console to stop this alarm. Note: This must be enabled on the DigitalDoorphone/ACP in order to provide the latch alarm. 39-ACP-01 must also be set to a value of 00.
PAGE 122
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Toll Control Forms Forms 51 through 56 set exceptions (allow) to rules defined in corresponding forms 61 through 66. Form 51 & 61 correspond to toll class setting 1 as per Form 18 of the Td-824i. Forms 52 & 62 correspond to toll class setting 2, through forms 56 & 66, which correspond to a setting of 6 on form 18.
PAGE 123
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 51 - Exception (Allow) Tables: Form 61 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 51 - Notes Entries on Form 51 provide exception (allowances) to a condition that is restricted on Form 61.
PAGE 124
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 52 - Exception (Allow) Tables: Form 62 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 52 Notes Entries on Form 52 provide exception (allowances) to a condition that is restricted o
PAGE 125
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 53 - Exception (Allow) Tables: Form 63 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 53 Notes Entries on Form 53 provide exception (allowances) to a condition that is restricted on Form 63.
PAGE 126
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 54 - Exception (Allow) Tables: Form 64 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 54 Notes Entries on Form 54 provide exception (allowances) to a condition that is restricted o
PAGE 127
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 55 - Exception (Allow) Tables: Form 65 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 55 Notes Entries on Form 55 provide exception (allowances) to a condition that is restricted on Form 65 In default any station allo
PAGE 128
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 56 - Exception (Allow) Tables: Form 66 - Deny Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Form 56 Notes Entries on Form 56 provide exception (allowances) to a condition that is restricted o
PAGE 129
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 57 - Exception (Allow) Tables: Form 58 - Exception (Allow) Tables: Entry Number 01 Entry Number 01 Actual Entry (Up to 12 digits in Length) 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Actual Entry (Up to 12 digits in Length) Page 129
PAGE 130
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 59 - Exception (Allow) Tables: Entry Number 01 Actual Entry (Up to 12 digits in Length) Entry Number 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 Actual Entry (Up to 12 digits in Length) Toll Control Examples This example is based on a location where 911 is enabled and all local calls are placed by dialing a 7 digit number.
PAGE 131
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 67 - Hunt Group Pilot Assignment: 67-grp Group Pilot Hunt Num. Number Type 01 Group Num. 02 03 04 05 06 07 08 09 10 Pilot Number Hunt Type General: This program sets Pilot Numbers for Hunting Groups 1 to 10. Description: There are 10 Hunt Groups available in the TD-824i. Each Hunt Group is assigned a Pilot Number in this form.
PAGE 132
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 68 - Day Hunt group assignments: Group Number 1 st Member 2 nd Member rd 3 Member th 4 Member th 5 Member Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Entries on Form 68 must be valid extension numbers. Extensions can be entered in any order.
PAGE 133
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 69 - Night Hunt group assignments: Group Number 1 st Member 2 nd Member rd 3 Member th 4 Member th 5 Member Group 01 Group 02 Group 03 Group 04 Group 05 Group 06 Group 07 Group 08 Group 09 Group 10 Entries on Form 69 must be valid extension numbers. Extensions can be entered in any order.
PAGE 134
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 70-Cd - ISDN Interface Specifications Program: IDSN=01 ISDN=02 ISDN=03 Cd=01 (Default=1) Cd=02 (Default=0) Cd=03 (Default=1) Cd=04 (Default=0) General: Assigns the ISDN interface to either “S” interface or “T” interface. Description: Cd= 01 is to assign the “S” or “T” interface for the ISDN port on G1-SIU card. 0= “S” interface. It can connect two ISDN devices.
PAGE 135
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 71-tk - ISDN Line Number Assignment Program: This form allows you to assign an identifying number to each B Channel of an ISDN line. Tk 01 and 02 correspond to ISDN circuit #1. Tk 03 and 04 correspond to ISDN circuit #2. Tk 05 and 06 correspond to ISDN circuit #3. A maximum of 12 digits can be assigned.
PAGE 136
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 74 - Least Cost Routing - Digit String Analysis Table: Numbers entered here are used for routing analysis.
PAGE 137
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 74 - Least Cost Routing - Digit String Analysis Table: Numbers entered here are used for routing analysis.
PAGE 138
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 76 - Least Cost Routing - Routing Table Normal Operation: This form determines the 20 Routing Tables that will be used during normal operation Modify Second Modify Third Start End First Trunk Digits Trunk Digits Trunk Table Time Time Group Table Group Table Group Numbe (2 (2 Preferenc (2 Preferenc (2 Preferenc r digits) digits) e (1 digit) digits) e (1 digit) digits) e (1 digit) Modify Dig
PAGE 139
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 76 - Least Cost Routing - Routing Table Special Day Rate: This form determines the 20 Routing Tables that will be used during Special Day Rate (05-13-07) Operation Modify Second Modify Third Modify Fourth Start End First Trunk Digits Trunk Digits Trunk Digits Trunk Table Time Time Group Table Group Table Group Table Group Numbe (2 (2 Preferenc (2 Preferenc (2 Preferenc (2 Preferenc r digits) digits) e (1 digit) digits) e (1 di
PAGE 140
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 76 - Least Cost Routing - Routing Table Second Special Rate Day Operation: This form determines the 20 Routing Tables that will be used during normal operation Modify Second Modify Third Modify Start End First Trunk Digits Trunk Digits Trunk Digits Table Time Time Group Table Group Table Group Table Numbe (2 (2 Preferenc (2 Preferenc (2 Preferenc (2 r digits) digits) e (1 digit) digits) e (
PAGE 141
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 77-num - Least Cost Routing - Modify Digits Table: System will delete the first nn digits (from 01 – 10) and then added the assigned digits in the front of the dialed numbers. Digits are deleted from the left most side of the dialing string. The added digits could be 0~9, *, #, p, T. ‘d’ is the wildcard. ‘-‘ means no digit. ‘p’ is the pause character.
PAGE 142
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 77-num – Least Cost Routing – Modify Digits Table (continued): Entry Digits to Digits to Insert Entry Digits to num delete (Up to 10 digits) num delete 51 76 52 77 53 78 54 79 55 80 56 81 57 82 58 83 59 84 60 85 61 86 62 87 63 88 64 89 65 90 66 91 67 92 68 93 69 94 70 95 71 96 72 97 73 98 74 99 Digits to Insert (Up to 10 digits) 75 Example: A u
PAGE 143
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Example 2: A customer has local lines and a Foreign Exchange (FX) into a town just across the state line (and in another area code). He wants to make sure calls to the other town always go over the FX. The telephone numbers for the next town use 5 different central office codes, 541 through 545. The area code for the next town is 838.
PAGE 144
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 78 - Station Class of Service (Part 6): Station Card #1 78-STN-- G1-a20u 01 02 03 04 05 06 07 08 0 1 0 0 0 1 2 0 01 02 03 04 05 06 07 08 01 02 03 04 05 06 07 08 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ Default Station Card #2 78-STN-78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ 78-_____ Station Card #3 78-STN-
PAGE 145
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 78 - continued Description: Form 78-ext-01 - Least Cost Routing Access Level: This parameter assigns the LCR routing level for each station.
PAGE 146
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 78-ext-06 – Reserved: Form 78-ext-07 – Auto Connect to Ringing Line: G1-a20u When set to 0 (Default) a station that is ringing on an incoming CO trunk is automatically connected to the station when the handset is lifted or the SPKR button is pressed.
PAGE 147
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Caller ID and Redial Patterns The bulk of programming necessary for addition of the Caller ID device is to implement Redial capabilities on identified calls. This is an issue that has kept most telephone manufacturers from incorporating redial on telephone systems equipped with Caller ID. Software shipped with the TD-824i properly addresses what we believe to be all the possible dialing situations in North America.
PAGE 148
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual 2. Local Toll (7 digit) Some localities (a good example is the state of Maine, in the northeastern U.S.) allows 7 digit dialing to the entire state, even though some calls are billed at toll rates. So a caller ID report from a telephone in the state of Maine to another telephone in the state of Maine will show 207 234 5678.
PAGE 149
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 5. Local Toll (1 + 10 digit) Some parts of the country require that in order to call a toll location within your own area code, you must dial 1 + Area Code + Office Code + subscriber number. In this application, we have to have the telephone system “know” which office codes are local and which are not local within the area code. We have to know this in order to be able to properly return a call.
PAGE 150
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 83 - Caller ID Block Assignment: This program divides Caller ID blocks for use by Stations. The number of memory buffers per block are assigned on Form 05-13-03. A Block of Caller ID memory may contain 10, 20, 30 or 40 records. The available number of blocks decreases as the number of records per block increases. Default is 10 records per block and 24 blocks per system.
PAGE 151
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 84-01 – Home Area Code: This is the area code where your own telephone numbers terminate. It is the area code portion of your phone number. It is 3 digits in length. Home Area Code Form 85-nn – Overlay Area Code: Some larger cities in the United States have exhausted an entire area code.
PAGE 152
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 86-nnn – Office Code Pattern 300—399: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 153
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 86-nnn – Office Code Pattern 400—499: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 154
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 86-nnn – Office Code Pattern 500—599: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 155
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 86-nnn – Office Code Pattern 600—699: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 156
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 86-nnn – Office Code Pattern 700—799: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 157
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Form 86-nnn – Office Code Pattern 800—899: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 158
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Form 86-nnn – Office Code Pattern 900—999: This form assigns proper redial pattern to each office code (only within your own area code). This is designed to provide you with the ability to differentiate between 7 digit dialing (local calls) and other calls within your own area code. There are three possible settings for calls within your own area code. You must define each type.
PAGE 159
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Programming Cross Reference By Application: Incoming Calls: RINGING ASSIGNMENT 01-tk-stn 02-tk-stn 05-01-05 05-02-07 05-02-08 05-08-01 20-nn 35-tk-07 35-tk-08 29-tk-04 29-tk-05 35-tk-06 44-st-04 35-TK Day Ringing And Ringing Line Preference Assignment Night Ringing And Ringing Line Preference Assignment Busy Reminder Tone Interval (Off-Hook Ringing/Camp-On) Ring On Timer (Minimum ring to be detected) Ring Off Timer (Time to hold s
PAGE 160
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual SPEED DIAL 05-01-06 05-03-02 05-04-06 05-05-03/04 09-spd-xx 42-stn-01/02 AUTO-REDIAL 05-02-03 05-03-02 05-05-07 05-05-08 Pause Duration for Speed Dial pauses Automatic Trunk Search During Speed Dial, Auto Redial, Saved Redial, etc.
PAGE 161
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Busy/During Conversation: HOLD AND HOLD RECALL 05-01-01 Hold Recall Timer (Time until station is warned of hold call) 05-01-02 Exclusive Hold Recall Timer (Same operation as hold recall) 05-01-03 Hold Recall Time out (Time before call is rerouted to Operator - After Hold Recall Timer has expired.
PAGE 162
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Night Service: 02 09-spd-nn 20-nn 35-tk-03 35-tk-04 Night Ringing And Ringing Line Preference Assignment System Speed Dial 101~109 for ECF Day/Night Service Schedule External Call Forward Location (Speed Dial Assignment) DISA/ECF, Day/Night Status Group Assignments: CONSOLE ASSIGNMENT 04-grp-stn Assign Stations to be consoles by group FLEXIBLE KEY GROUP ASSIGNMENTS 07-grp-key Key Group Layout
PAGE 163
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual 13-04 Password for Monitoring over DISA (defaulr=none) STATION LOCK/UNLOCK 40-stn-07 Station Lock/Unlock Status BUSY OUT A TRUNK 37-tk-x Taking a trunk out of service INTERCOM DIALING RESTRICTIONS 45-stn-01 Restrict station to station intercom dialing System Clock: DATE AND TIME SETUP 05-04-04 12/24 hour time format 11Set the system time 20-nn Day/Night schedule Definition SYSTEM ALARM 12-nn 44-stn-01 System Alarm Clock Statio
PAGE 164
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual PAGING 07-grp-key 40-stn-05 40-stn-06 41-stn-01 Paging key Station Paging Access Deny/Allow Receive Page Over Speaker Deny/Allow Station Page Group Optional Services: DOOR PHONE & DOOR SWITCH 03-01-ext Stations to ring upon Door Phone Activation 05-12-04 Door Relay Activation Timer 06-01-fn Relay Assignment (for doorphone latch release) ACCESS CONTROL PHONE 13-05 Pass word for entry from ACP 4
PAGE 165
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual Voice Mail: 05-12-05 43-prt-02 35-trk-07 35-trk-08 67-grp 68-grp 69-grp Set Voice Mail integration type Set equipment type for Voice Mail Port Set ring type (day) Set ring type (night) Set Hunt group Pilot number and hunt type for VM Set Hunt group members for VM (day) Set Hunt group members for VM (night) Hunt Groups: 67-grp 68-grp 69-grp Set Hunt group Pilot number and hunt type Set hunt group members for (Day) Set hunt group
PAGE 166
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual By Program Type in Alphabetical Order: System Parameters: 12/24 Hours Clock ACD - 1 Enable Time ACD - 1 Release Time ACD - 1 Segment 2 Recall Time Action For Call Duration Limiting Auto Redial Pause Time Auto Redial Ringing Time – PSTN Lines Auto Redial Times Automatic Trunk Search Busy Remind Cycle Time (Off-Hook Ringing) Call Cut Off Timer – No Polarity Reversal Received Call Forward No Answer
PAGE 167
TransTel Model TD-824-I Digital Telephone System – Programming Forms Manual ISDN interface specifications 70-CD ISDN line number assignment 71-CH Least cost routing (analysis table) 75-NUM Least cost routing (modifying table) 77-NUM Least cost routing (routing table) 76-NUM Least cost Routing – Weekly Holiday 05-13-07 Least cost Routing – Weekly Weekend 05-13-08 LED Indication Of Check In/Check Out 05-12-07 Linear/Circular Trunk Group Access 05-12-06 Make/Break Ratio 05-03-01 Message Waiting Method For Ana
PAGE 168
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual ACP Encode key card ACP Register key card Alarm signaling type Allow Trunk Access Allow Unrestricted Speed Dial Access Associated loud bell Automatic Answer Capability Be paged by others Call duration limit Call Hold Call Split CTI-Extension Status Report Dial (87) Trunk Group Dial 9 Trunk Group Direct CO access DISA Recall Capability Disallow SLT Connection Door Unlock/DND/CFWD Access DTMF Rece
PAGE 169
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual TransTel Key Telephone Operation Manual. Introduction This section is devoted to an explanation of the implementation and operation of TransTel electronic telephones (keysets). Included are normal functions that are available to most station users and functions that are available only to console operators.
PAGE 170
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Answering Calls There are several ways that you may answer calls at Your telephone. Depending on the particular type of call and the system programming, calls may require different actions in order to answer them. Intercom Calls Voice Announce Call: If the system is programmed for Voice Announce calls, you will hear a quick tone. The calling party will then be routed to your speaker.
PAGE 171
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual External Calls Not Ringing At Your Set Calls With CO Line Appearance: Incoming calls on a line that appears on your set may be picked up by pressing the flashing CO line key. You will be connected to the call. Note: This feature depends on system programming. On some systems this option may be disabled. If that is the case, this procedure will not work.
PAGE 172
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual To respond to a Callback: 1. If you are on a conversation and a callback has been left on your telephone and you have an LCD display it will indicate in the lower portion of the LCD: MSG ST:XX Also, your Message key will flash. This tells you who is leaving the callback message. 2. You may place your existing call on hold and hang up or simply hang up.
PAGE 173
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Press SAVE. Your Display (if you have one) will show “Auto Save.” Hang up. You may make 1 or a hundred calls (or more if you need to…) in between. Press SAVE. Your telephone will redial the number you previously saved and remain off hook for at least 10 seconds (depending on system programming). And will continue to redial the number periodically for a number of times (the number of times also depends on system programming).
PAGE 174
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Delete Caller ID Record: 1. While reviewing a Caller ID record, you may delete it by pressing the [TSF] key. To exit Caller ID Review Mode: 1. Press the [SPK] key. Call Forwarding To forward All calls: Press PGM. Enter CFD Dial the extension number where you want to forward your calls. Press 1 for All Calls. Your telephone will return to idle. Your telephone is now forwarded.
PAGE 175
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual To forward calls when you don’t answer or are busy: Press PGM. Enter CFD Dial the extension number where you want to forward your calls. Enter 3 for No Answer / Busy Conditions. Dial the extension number where you want to forward your calls. Your telephone will return to idle. Your telephone is now forwarded.
PAGE 176
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual DIRECT (EXTENSION) CALL PICKUP This allows you to answer a specific station that is ringing. Lift the handset or press SPKR. Press the * key on the dial pad. Dial the extension number of the station that is ringing. You will be connected to the caller. ALL GROUP PICKUP You can pick up any ringing call in the system using this method. You will pick up the oldest ringing call.
PAGE 177
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Dial the station number where the call needs to go. Wait for the station to answer. Press TRF/FL or hang up (depending on programming). The call has been successfully transferred. If you have a DSS button for the station where you transfer the call, you do not need to press the HOLD button first. Just press the DSS button for the station where you want to transfer the call.
PAGE 178
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Conversation monitor If you need to monitor a conversation for any reason, this feature will let you observe an existing conversation. Please be aware that this option is a level controlled option (from system programming), so you may be able to override no phones, a few phones or all phones, depending on your telephone’s access level. Some stations may not have access to this feature.
PAGE 179
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual 3. Select the directory that you want to utilize by pressing either [1], or [2]. Note: Depending on how your system is programmed, steps 2 and 3 may not appear. 4. The LCD will display: ENTER LETTER 5. Using the numbers on the keypad, enter the first letter of the name that you want to dial. 6. When the letter that you want is displayed in the lower left corner of the LCD, press [VOL ].
PAGE 180
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Press HOLD HOLD (that’s pressing HOLD twice). The call is placed on Exclusive Hold for your extension. You can alternate between Exclusive Hold and System Hold with each press of the HOLD key. As noted above, to place a call on Exclusive Hold, press HOLD twice. Pressing HOLD again will return the call to regular system hold. Another press of the HOLD key will return the call to Exclusive Hold.
PAGE 181
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Group Listen Added in G1-a20u. For DK2 sets (s/w version 22 and newer) and DK3 sets (s/w version 15 and newer), Group Listen may be selected. This function keeps the handset operational and also activates the speaker. To use Group Listen, keep the handset off hook and press the SPK button. The conversation can now be heard over the speaker as well as the handset. However, the microphone in the handset remains active.
PAGE 182
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Immediate CO Line Access Immediate Line Access will connect you to the first available line in your Dial 9 Group when you lift the handset while in an idle state. To Enable/Disable: 1. Press [7], [7], [1]. 2. If Auto Line Access was previously disabled, it is now enabled. If it was previously active, it is now disabled. Note: Automatic Line Access is only applicable when the handset is lifted.
PAGE 183
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Mute Use the mute function any time you don’t want the outside party to hear what you are saying. While you are on the handset: Press MIC/AT key. The microphone on the handset will be muted. The LED on the MIC/AT button will flash rapidly. Press MIC/AT key. The microphone on the handset will be enabled. The MIC/AT button will go dark. While you are on the speakerphone: Press MIC/AT key.
PAGE 184
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual All Paging Lift the handset or press SPKR. Press # and 0. Pulse To Tone Conversion This feature is of use to you if you are located in an area where your telephone company does not accept DTMF (Touch Tone),This feature lets you dial DTMF (Touch-Tone) for services such as remote voice mail, bank by phone, etc. Press MSG key.
PAGE 185
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Saved Number Redial (SuperSave) You are on an outside call and you need to save a number for dialing later. Supersave provides a way for you to save the number to your telephone set so that you can dial it later. SuperSave: 1. You are on an outside call. 2. Press [SAVE]. 3. Dial the new telephone number that you wish to save. 4. You may hang up. 5. Make other calls if you wish. 6. While your telephone is idle, press [SAVE].
PAGE 186
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Programming Personal Numeric Speed Dial Press PGM Press SPD. Press the number that you want to program (0-9). (If you want the speed dial number to access a specific telephone line every time it places the call, Press the MIC button and dial 0 plus the line number. Otherwise skip this step.) Enter the telephone number you want to dial. Press SAVE. Press SPKR.
PAGE 187
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Station Lock / Unlock This feature lets you lock your telephone so that no one can make unauthorized telephone calls on it. In order to unlock your telephone, you must remember the 3 digit long “password” that you enter when you lock it. You will need this to unlock your telephone.
PAGE 188
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Timed Reminder or Wake Up With this feature, you can set an appointment reminder, that will alert you only once, or you can set a daily reminder that will happen every day at the same time (like when it’s time to stop working and go home). Note: If you are a system operator, the procedure you follow will be different. Please see Operator Timed Reminder or Wake Up. Press PGM. Press HOLD.
PAGE 189
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Voice Service Unit (Operator Function) The Voice Service Unit has up to 8 channels on which you can record up to 8 different messages. The actual number of messages that you record will be determined by how your system is programmed. This section explains how to record and playback the messages so that the system can use them. Remember, the Voice Service Unit allows a maximum of 60 seconds total recording time.
PAGE 190
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Voice Mail Live Call Recording Live Call Recording allows you to record a conversation directly into your mailbox for retrieval at a later time. During a Conversation: 1. Press the Record key on your telephone set. The voice mail system will be notified of your request to record the conversation automatically.
PAGE 191
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Volume Levels Programming (Permanent) You can permanently set the volume levels on your telephone. Press PGM. Press 6. Dial 1 to set Ringing Volume. OR Dial 2 to set Speaker Volume. OR Dial 3 to set Handset Volume OR Dial 4 to Set Ringing Volume Increase (Rings louder as the call ages) OR Dial 5 to set the Ringing Frequency (Pitch) And adjust the pitch using your volume up and down keys on your telephone.
PAGE 192
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Access Control Phone Operation Manual Intercom (as doorphone) Operation: 1. Press to call the associated hunt group and open the door; or 2. Dial extension number, then press Note: to call an individual extension to answer and open the door.
PAGE 193
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Note: On invalid password or card, ACP will play busy tone for 5 sec and display will show ‘ERR’. Check out (lock) ACP (as wall mount phone) Operation: 1. 2. +[8]+[password (3-digit)] to lock up ACP (as wall mount phone) to prevent it from use by others. +[#]+[password (3-digit)] to un-lock ACP (as wall mount phone) for temporary use (making a call) by the owner. After the use, ACP is locked up again.
PAGE 194
TransTel Model TD-824-I Digital Telephone System - General Description - Installation - Programming Forms Manual Burglary Report When the sensor is opened, ACP will signal PC for application of warning or asking help. (Not currently available) Time Display When ACP is idle, display will show the time (’08.30’ for 8:30AM). As a wall mount phone When ACP is in use of as a wall mount phone, ‘auto answer’ is operational for both intercom call and incoming call.
PAGE 195
TransTel Model TD-824-I Digital Telephone System – Key Telephone Operation Manual Station Function Form 46-st-08 There are three parameters under control of 46-st-08. 1. ACP Functions as: a. Doorphone b. Wall Mount Telephone 2. Door lock function activates the relay: a. in the ACP b. in the KSU. 3. Security Access is: a. Via password OR Identification Card b. Via password AND Identification Card.