IONBEAM GROW LIGHT BAR SYSTEM USER MANUAL1
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com and click contact for our contact information. EMAIL WEB LOCATION support@acinfinity.com www.acinfinity.
MANUAL CODE NE2201X1 4 PRODUCT MODEL UPC-A IONBEAM S11 IONBEAM S16 IONBEAM S16-UV AC-NES11 AC-NES16 AC-NEU16 819137023352 819137023369 819137023475
MANUAL INDEX Manual Index ................................................................................. Page 5 Product Warning ............................................................................ Page 6 Key Features ................................................................................. Page 7 Product Contents ........................................................................... Page 8 Installation .................................................................................
PRODUCT WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Ensure your power source conforms to the electrical requirements of this product. 2. Read all instructions before installing and using this product. 3. Be careful not to damage or cut the wire insulation (covering) during the installation. Do not permit wires to come in contact with any sharp edges. 4.
KEY FEATURES UISTM COMPATIBILITY DIMMER AND TIMER HUMIDITY-RESISTANT Compatible with select UIS controllers to access climate triggers, timers, grow cycles, scheduling, and transitions. Adjust four light intensity levels for each grow stage and set four timer settings that repeat daily. Unibody construction tightly sealed to IP-65 standards to block liquid and dust from entering and seeping through.
PRODUCT CONTENTS (X) = Full Spectrum Models, [X] = Ultra-Violet Model LIGHT BAR (SINGLE-CORDED) (x1) [x1] POWER ADAPTER (x1) HOOK AND LOOP CABLE TIES (x4) [x2] 8 LIGHT BAR (DUAL-CORDED) (x3) [x1] UIS EXTENSION CORD (M-M) (x1) WIRE MOUNT (x8) [x4] LIGHT CONTROLLER (x1) [x1] MOUNTING BAR (x4) [x2] BAR EXTENSION CORD (M-F) (x3) [x1] WOOD SCREWS (WALL MOUNT) (x9) [x4]
INSTALLATION LIGHT BAR CHAIN ASSEMBLY STEP 1 Connect the single-corded LED light bar's female port to the dual-corded LED light bar's male connector. Repeat this with as many light bars as needed. F M 1 STEP 2 Connect the light controller's male connector to the other end of the dual-corded LED light bar. STEP 3 Connect the power adapter to the light controller. EXTENDING THE CHAIN You may connect the included bar extension cord in between any link in this light bar chain to lengthen it.
INSTALLATION LIGHT BAR MOUNTING POLE MOUNTING You may magnetically mount the light bar(s) directly on your grow tent steel pole. You may also use the included hook and loop cable ties around the light bar(s) and mounting bar to adjust the lighting angle and for extra security. CANVAS MOUNTING You may magnetically mount the light bar(s) to the wall or ceiling of your grow tent. Set the included mounting bar(s) on the outer side of your tent. Place the light bar(s) at the exact spot on the inner side.
INSTALLATION LIGHT BAR MOUNTING STEP 1 — WALL MOUNTING Make sure your mounting area is free from obstruction. Use a mounting bar to mark your drilling holes with the logo facing the wall. STEP 2 — WALL MOUNTING Drill holes into the marked locations.
INSTALLATION LIGHT BAR MOUNTING STEP 3 — WALL MOUNTING If you are mounting onto anything other than a wood support or stud, insert the included four wall anchors into the drilled mounting holes. You may need to use a hammer to secure them through the holes. STEP 4 — WALL MOUNTING Align the mounting bar holes with the wall anchors, making sure the logo faces the wall. Screw or drill in the wood screws to secure the mounting bar. Repeat steps 1-4 as needed.
INSTALLATION LIGHT BAR MOUNTING STEP 5 — WALL MOUNTING Set the light bar(s) magnet ends onto the mounting bar(s).
INSTALLATION CONTROLLER MOUNTING MAGNET MOUNTING You may magnetically mount the light controller onto any steel surface. STEP 1 — WALL MOUNTING Locate a spot free of obstruction and secure the anchor into your wall. Twist the wood screw into the anchors. STEP 2 — WALL MOUNTING Use the mounting hole located on the back of the controller for wall mount.
INSTALLATION POWERING STEP 1 Plug the power adapter into a wall outlet.
PROGRAMMING 1. LIGHTING Pressing the light button will increase the light intensity level in 10/30/60/100% increments, displayed with white LED indicators. Pressing this button at 100% intensity will cycle to 0%. Holding the light button will shut off the lighting. Pressing it again will return the light intensity to its previous setting. 2. TIMER Pressing the clock button will set the timer in 3/6/12/18-hour increments, displayed with orange LED indicators.
STARTER GUIDE FULL SPECTRUM LIGHTING The charts below offer suggested mounting heights and light intensities for each stage in the growing process. These factors will vary based on the plant you are growing. Height refers to the minimum recommended distance from the canopy (tip of the plant) to the light. GROW STAGE Height Intensity Seedling Stage 1 IN. 10%* Vegetative Stage 2 IN. 30% Set-Up *Also recommended for plant propagation.
STARTER GUIDE FULL SPECTRUM LIGHTING 18 GROW STAGE Height Intensity Vegetative Stage 6 IN. 60% Flowering Stage 6 IN.
STARTER GUIDE FULL SPECTRUM LIGHTING SETTING ACTIVE LIGHTING TIMERS The included controller can set timers in 3/6/12/18-hour increments. Use either the 3HR or the 6HR timer to extend your plant's daily exposure to light, in conjunction with natural sunlight, or when growing plants that don't require extended exposure to lighting. Use either the 12HR or the 18HR timer to complement common light cycles used to grow high yield plants indoors.
CONNECTING TO UISTM AN INTERCONNECTED GROW SETUP The Universal Infinity System (UIS) is a series of controllers and devices that come together to create a fully automated system. UIS enables our controllers to simultaneously connect with various grow equipment such as inline fans, clip-on fans, and grow lights.
CONNECTING TO UISTM IONBEAM LED grow lights can connect with select smart controllers as part of an integrated system using the included UIS extension cord. CONNECTING TO UIS CONTROLLERS Use the included UIS M-M extension cord to connect the LED light bar(s) to your selected UIS controller via the light controller's side port. Your selected UIS controller will override all of the light controller's onboard settings when connected in this manner.
AC INFINITY PRODUCTS Advance Grow Tents The CLOUDLAB series is a line of grow tents designed to create ideal growing conditions and facilitate indoor plant cultivation year-round. Features 2000D thick oxford canvas lined with inner diamond patterned mylar that maximizes grow light luminosity, and a reinforced frame with 150 lb. weight capacity. Includes a mounting plate to install your AC Infinity controller onto.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues. The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships.
COPYRIGHT © 2022 AC INFINITY INC. ALL RIGHTS RESERVED No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific permission from AC Infinity Inc.
www.acinfinity.