CONTROLLER 69 WIFI USER MANUAL
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com and click contact for our contact information. EMAIL WEB LOCATION support@acinfinity.com www.acinfinity.
MANUAL CODE CTR69X2202X1 PRODUCT MODEL UPC-A CONTROLLER 69 WIFI CTR69X 819137023406 FAN COMPATIBILITY This controller is natively compatible with AC Infinity devices with UIS™ connectors. Older model inline fans with EC motors may be used with this controller using a Molex adapter. An EC-motor fan will have two cords coming out of its motor box for the power and the controller. Note that certain models that previously used DC-motors now contain EC-motors in updated builds.
MANUAL INDEX Compatibility .................................................................................. Page 4 Manual Index ................................................................................. Page 5 Product Warning ............................................................................ Page 6 Interference from MH and HPS Lights ........................................... Page 7 Key Features .................................................................................
PRODUCT WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Ensure your power source conforms to the electrical requirements of this product. 2. Check your local code restrictions for additional safety measures that may be needed for a proper code compliant installation. 3. Read all instructions before installing and using this product. 4.
INTERFERENCE from MH and HPS LIGHTS Certain grow light models with HID* ballasts that do not use electromagnetic shielding will create an area of radio frequency interference (RFI). This can distort nearby frequency-sensitive components like internet lines and climate sensors. RFI can be emitted from the ballast’s cords or the ballast itself.
KEY FEATURES SMART CONTROLLER VERSATILE PLACEMENT APP-CONTROLLED Features automation controls that activate your devices based on climate conditions, timers, and schedules. Mount the controller on a steel surface using the rear magnet or open the kickstand to sit it tilted on your desktop. WiFi-enabled to connect to the AC Infinity app for remote access to smart automations, climate data, and history logs.
PRODUCT CONTENTS SMART WIFI CONTROLLER (x1) SENSOR PROBE (x1) UIS M - 4PIN F ADAPTER (x2) CONTROLLER PLATE BOLTS (x2) WOOD SCREWS (WALL HANG) (x2) WIRE TIE (x1) 9
POWERING AND SETUP STEP 1 Plug your device’s UIS connector into one of the controller's ports. STEP 2 Plug the sensor probe into the controller’s 3.5mm jack. Set the probe near your plants in your grow tent for the most accurate reading.
POWERING AND SETUP STEP 3 Plug your device’s power cord into an AC power outlet to power it and the controller. STEP 4 You may use the included tie mounts, wood screws, and zip ties to cable manage the cords. Secure the tie mounts onto a surface using the wood screws. Loop the zip ties around the cords into the tie mounts.
CONTROLLER MOUNTING STEP 1 — WALL MOUNTING Locate a spot free of obstruction and secure the anchors into your wall. Twist the wood screws into the anchors. STEP 2 — WALL MOUNTING Hang the controller by the screws using the holes on the backside.
CONTROLLER MOUNTING MAGNET MOUNTING You may also mount the controller onto a steel surface using the magnet located behind the label. PLATE MOUNTING* Screw the bolts into the slit at the upper half of the plate. Hang the controller by the bolts using the holes on the backside.
CONTROLLER MOUNTING T-SERIES CORD ARRANGEMENT Cords may be routed into or outside of the kickstand grooves, and through a cut hole behind the controller. KICKSTANDING Open the stand behind the controller to set it tilted on your desktop.
UNIVERSAL INFINITY SYSTEM The Universal Infinity System™ enables you to connect a single central controller with several grow devices simultaneously. By creating this fully integrated system, you can power and program all your devices together or separately for optimized grow tent management. Use select smart controllers to set triggers that will activate your devices based on your grow tent’s temperature and humidity.
UIS COMPATIBILITY MOLEX ADAPTER Use the included Molex adapter to plug inline fans with 4-pin Molex connectors into this controller. Plug your fan's Molex connector into the adapter. Then plug the adapter into the controller. UIS M - 4PIN F ADAPTER EXTENSION CABLE* Use male-to-male UIS extension cords to connect devices with female UIS ports at an extended range from your controller. Included with UIS-compatible devices.
ADDING MORE DEVICES The CONTROLLER 69 is built with four ports that enable you to power and control multiple devices at the same time. See image below for a sample configuration.
ADDING MORE DEVICES USING THE DONGLE Each controller port can support mix-andmatched devices regardless of their size. When using a 2-port or 4-port dongle, plug your first device into Port 1 for the controller to recognize as the primary device. All other devices plugged into the dongle will follow programming intended for the device plugged into Port 1. 1 2 3 4 1 2 3 4 1 2 Dongles are not included and sold separately.
PROGRAMMING 1. PORT BUTTON Cycles through up to four connected devices. Each device is programmed independently, or together when navigating to ALL. 2. MODE BUTTON 3. SETTING BUTTON Cycles through the controller’s modes: OFF, ON, AUTO (4 triggers), TIMER to ON, TIMER to OFF, CYCLE (ON and OFF), and SCHEDULE (ON and OFF). Cycles through the controller’s settings: DISPLAY, CLOCK, °F/°C, CALIB. T°/H%, and TRANS.T°/H%. 4. UP/DOWN BUTTONS Adjusts the value of your current mode.
PROGRAMMING PORTS Pressing the port button will cycle through the controller’s available ports: ALL, 1, 2, 3, and 4. Dot indicates the current device. No digit is displayed if a device is not plugged into the corresponding port. ALL PORTS Navigate to the ALL port to set simultaneous programming for all connected devices. Programming set in this port mode applies to all connected devices, but will not be active if you navigate to other ports. Re-entering the ALL port will resume its programming.
PROGRAMMING CONTROLLER MODES Pressing the mode button will cycle through the controller’s available programming modes: OFF, ON, AUTO (4 triggers), TIMER TO ON, TIMER TO OFF, CYCLE (On and Off), and SCHEDULE (On and Off). OFF MODE (MINIMUM LEVEL) Your devices will not run while in this mode. The level set while in this mode establishes the minimum level in other modes. When the devices are triggered to turn OFF in all other modes, they will instead run at the level set here.
PROGRAMMING AUTO MODE (HIGH TEMPERATURE TRIGGER) Pressing the up or down button sets the high temperature trigger. The devices will activate if the probe’s reading meets or exceeds this threshold. Once triggered, the devices will gradually ramp up to the level set in ON mode. If the probe’s reading falls below this trigger point, the devices will gradually slow down to a stop or at the level set in OFF mode.
PROGRAMMING AUTO MODE (HIGH HUMIDITY TRIGGER) Pressing the up or down button sets the high humidity trigger. The devices will activate if the probe’s reading meets or exceeds this threshold. Once triggered, the devices will gradually ramp up to the level set in ON mode. If the probe’s reading falls below this trigger point, the devices will gradually slow down to a stop or at the level set in OFF mode.
PROGRAMMING TIMER TO ON MODE Pressing the up or down button sets a countdown time. Once the timer ends, the devices will trigger to run at the level set in ON Mode. If there is a level set in OFF Mode, the devices will run at that level during the countdown. The countdown will begin if no buttons are pressed for 5 seconds. The time left on the countdown is displayed below the current level. Leaving the timer mode while the countdown is running will pause it until you return to this mode.
PROGRAMMING CYCLE MODE (ON AND OFF) Set an on duration and an off duration for the devices to cycle through continuously. Press the up or down button to first set a duration for the devices to activate. Then press the mode button again and set a duration for the devices to deactivate. When the devices are activated, they will run at the level set in ON Mode. When the devices are deactivated, they will run at the level set in OFF Mode. The countdown will begin if no buttons are pressed for 5 seconds.
PROGRAMMING SCHEDULE MODE (ON AND OFF) Sets an on clock-time and an off clock-time schedule for the devices to follow daily. Press the up or down button to first set up an on clock-time to trigger ON mode, then press the mode button to set an off clock-time to trigger OFF mode. Please be sure to set the current clock time under settings. When the devices are triggered to activate, they will run at the level set in ON Mode.
PROGRAMMING CONTROLLER SETTINGS Pressing the setting button will cycle through the controller’s available settings: DISPLAY, °F/ °C, CLOCK, CALIB. T°, CALIB. H%, TRANS. T°, and TRANS. H%. DISPLAY SETTING Adjusts the display brightness and auto-dimming. Press the up or down button to cycle through levels 1, 2, 3, A2 and A3; 3 being the highest brightness setting, while 1 is the lowest. In settings 1, 2 and 3, the display will stay at that brightness level and will not automatically dim the display.
PROGRAMMING °F/°C SETTING Changes the displayed units to Fahrenheit or Celsius. Press the up or down button to cycle through F and C. All displayed units will automatically convert when adjusting this setting. CLOCK SETTING Adjusts the current clock time. Press the up or down button to increase or decrease the time. Once you cycle through 12:00 each time, the units will automatically change to AM or PM. The clock time is located at the top right corner of the display.
PROGRAMMING CALIBRATION TEMPERATURE SETTING Adjusts the temperature reading the sensor probe is measuring. Press the up or down button to increase or decrease the data figure in 1° increments. The calibration cycle ranges from -20°F to 20°F (or -10°C to 10°C) and will be applied to the sensor probe’s measurements. CALIBRATION HUMIDITY SETTING Adjusts the relative humidity reading the sensor probe is measuring. Press the up or down button to increase or decrease the data figure in 1% increments.
PROGRAMMING TRANSITION TEMPERATURE SETTING Customizes how the device will ramp up in levels when triggered ON by temperature in AUTO MODE. Set a transition threshold to determine how much the probe temperature would need to surpass your trigger point for the device to increase in level by one. The higher the transition threshold figure is set to, the more the probe temperature would need to surpass your set temperature trigger for the level to increase.
PROGRAMMING TRANSITION HUMIDITY SETTING Customizes how the device will ramp up in levels when triggered ON by humidity in AUTO MODE. Set a transition threshold to determine how much the probe humidity would need to surpass your trigger point for the device to increase in level by one. The higher the transition threshold figure is set to, the more the probe humidity would need to surpass your set humidity trigger for the level to increase.
PROGRAMMING ALERT ICONS The alert icons are displayed at the top of the screen. Icons may flash when the controller signals an alert to notify you of any triggered function or alarm. ADVANCE PROGRAMMING Displays when an advance program set in the app is active. "ADV." will appear and override the controller if an automation program is in use. AUTO MODE ALERT Flashes whenever any of the auto mode triggers (high temperature, low temperature, high humidity, or low humidity) activate your devices.
PROGRAMMING WIFI Appears when the physical controller is connected to the app via WiFi. DISPLAY LOCK ALERT Displays when you lock the controller. The icon will flash and beep if you attempt to adjust the controller while it is still locked. TEMPERATURE/ HUMIDITY ALARM Flashes and beeps with alarm if the temperature/humidity meet the trigger point set in the app.
MAX AND MIN SETTINGS MAXIMUM LEVEL You can determine what level the device will run at when its triggered ON. This can be set in ON MODE. The level you leave that mode in will be used as the level the device will run at when triggered ON. This includes AUTO MODE, CYCLE MODE, TIMER TO ON MODE, TIMER TO OFF MODE, and SCHEDULE MODE. Do not set the figure in ON MODE to zero or the device will turn off when it’s triggered ON in all modes.
OTHER SETTINGS FACTORY RESET Holding the mode, up, and down buttons together for 5 seconds will reset your controller and restore factory settings. This clears all user parameters in each controller mode and setting. HOLD + CONTROLLER LOCK Holding the setting button will lock the controller in your current mode. While your controller is locked, no parameters may be adjusted, nor will you be able to switch modes. Holding the setting button again will unlock the controller.
DOWNLOAD THE APP THE AC INFINITY APP The AC Infinity app enables you to connect with the next generation of our intelligent controllers, giving you access to advance programs and environmental data*. 1 Download the AC Infinity app from the App Store or Play Store by searching “AC Infinity”. 2 Open the AC Infinity app and follow the instructions on page 37-38 to pair your controller with the app. HOW TO USE THE APP Visit our website at www.acinfinity.
ADD A DEVICE SETUP AND PAIRING Power your device on before pairing your controller with the app. Logging in or creating an account beforehand will expedite the pairing process. Have your WiFi network's name and password ready. 1 2 Tap on the “+” tab to add your smart device. Select "Smart Controllers". + WiFi and location permissions must be enabled on your mobile device before starting the pairing process.
ADD A DEVICE 3 Select CONTROLLER 69 WIFI. 38 4 Log in or create an account to continue.
ADD A DEVICE 5 Hold the port button for 5 seconds to activate WiFi. Wait for the WiFi icon to start flashing on your controller’s screen to release the button. 6 The app will search for and pair with the controller you have activated. When pairing the app around multiple controllers, move your mobile device closer to your desired controller.
ADD A DEVICE 7 8 Enter your WiFi network's password. You may also connect to an alternate 2.4GHz router*. Follow these tips if the pairing process is unsuccessful. *This controller is only compatible with 2.4 GHz frequency band routers. Make sure your mobile device is not 40 connected to a 5 GHz frequency band network.
ADD A DEVICE 9 10 Tap the DONE button to complete the pairing process. Your controller will appear in your smart device with a unique ID.
CONTROLLER 69 FAQ Q: What devices are compatible with the CONTROLLER 69 WIFI? A: All AC Infinity devices that contain a UIS connector are compatible. If your AC Infinity device has a 4-pin Molex connector and an EC motor, it may still be compatible with the use of a UIS adapter to convert its connector to fit with the controller. Q: What does “level” refer to in the controller and app? A: The level represents the intensity the device is running at. This is represented by a digit 0 to 10.
CONTROLLER 69 FAQ Q: How do I stop my device from turning on and off too quickly in AUTO Mode? A: The figure set in the TRANSITION under SETTINGS will determine how the device ramps up in levels when triggered to run in AUTO Mode. Set a transition threshold X. For every multiple of X that has surpassed your trigger point, the device will increase by one level. The lower the transition threshold is set to, the easier it will be for the device to ramp up in levels.
CONTROLLER 69 FAQ Q: Will I be able to use this controller with my own fan? A: The CONTROLLER 69 WIFI is only compatible with AC Infinity fans that use EC motors. Q: Does the controller retain its settings after power is shut off? A: Yes. If the controller's power is cut off and is powered on afterward, your settings will remain. Q: My controller isn't pairing with the app. How do I fix this? A: If the pairing process isn't successful, press any button to return to the normal screen.
AC INFINITY PRODUCTS Advance Grow Tents The CLOUDLAB series is a line of grow tents designed to create ideal growing conditions and facilitate indoor plant cultivation year-round. Features 2000D thick oxford canvas lined with inner diamond patterned mylar that maximizes grow light luminosity, and a reinforced frame with 150 lb. weight capacity. Includes a mounting plate to install your AC Infinity controller onto.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues. The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
www.acinfinity.
