TVAC16000B User guide Version 01/2013 Original user guide in English.
English Introduction Dear customer, Thank you for purchasing this product. This product complies with current domestic and European regulations. Conformity has been verified, and all related certifications and documents are available from the manufacturer on request (ABUS Security-Center GmbH & Co. KG, Linker Kreuthweg 5, 86444 Affing, Germany).
English Explanation of symbols The triangular high voltage symbol is used to warn of the risk of injury or health hazards (e.g. caused by electric shock). The triangular warning symbol indicates important notes in these operating instructions which must be observed. This symbol indicates special tips and notes on the operation of the unit. Important safety information All guarantee claims are invalid in the event of damage caused by non-compliance with this user guide.
English 7. Wireless transmission The wireless range depends on a variety of environmental factors. The local conditions at the installation site may have a negative impact on the range. When there are no obstructions between the receiver and transmitter, a range of up to 150m is possible, but this range will be considerably less within buildings.
English Contents 1. Intended use.............................................................................................................................. 6 2. Scope of delivery ....................................................................................................................... 6 3. Features and functions .............................................................................................................. 6 4. Device description .......................................
English 1. Intended use This 7" touchscreen wireless monitor and the IR wireless outdoor camera enable you to easily transmit and display video signals wirelessly across moderate and large distances. Wireless signal transmission is an advantage everywhere cables are not able to be laid: the camera transmits the video signal wirelessly to the wireless monitor. The conversion to digital signals means that malfunctions and interference can be reduced.
English 4. Device description 4.1 Monitordescription c d c f g h e e c d e f g h Power button Antenna Fold-up stand SD card slot Reset button 5VDC/1A power supply 4.
English 4.3 Camera description c N O P Q R S T U V c d e f g h j Link LED P Fixed lens Power LED Link LED IR LED Photo sensor Camera mount Microphone Pairing button Power supply connection 5 VDC / 1A k V i Meaning of the LEDs: LED Power LED O Antenna Status On (red) Off Flashing Meaning Camera on Camera off The camera is in the “Pairing Mode”.
English 5. Installation 5.1 Installing the monitor 1. 2. Connect the power supply unit to the monitor. Switch the device on. Press the power button for about 5 seconds. Important: Please note that if the monitor does NOT have an external power supply, it must be charged for at least 8 hours prior to being used for the first time. The batteries will provide power for approx. 1.5 hours. Important: The integrated battery allows you to use the LCD monitor flexibly.
English 5.3 Connecting the docking station to the network To connect the docking station to the internet, proceed as follows: 1. Connect the network cable to your router and the docking station. 2. Connect to the network only after you have made all the required settings on the monitor. The network settings are described in 6.4.3. 3. After the network is set up, click on the internet”.
English Screw the camera onto the mount and connect the power supply unit to the camera. 6. Operation To switch the monitor ON / OFF, press and hold down the power button for at least 5 seconds. 6.1 Main menu c c d e d e Live view Event list Settings An ongoing recording always stops as soon as you enter the main menu.
English 6.2 Live view c d e f g h i k j V Explanation of symbols SD card display No SD card c SD card detected and almost empty SD card full Tip: Always switch off the device before removing the SD card. Note that the device does not have a cyclic recording function. Once the SD card is full, no more recordings can be saved. If you want to record longer time periods on the SD card, buy a larger card.
English Timer f Schedule has been saved This symbol appears if a programmed recording is running. Recording status g Flashes red: the device is recording Constantly red: device is not recording If you press the REC symbol directly, you start a manual recording. Select this again to stop the recording. Camera number and reception h Reception of the camera very good No reception The wireless transmission range depends on the environmental factors (e.g.
English Network connection This option is only available if the monitor is on the docking station and the network cable is connected to the docking station as well as the router. Press the network symbol and select whether the object should be connected to the internet or whether the device should just be charged. Important: Set up the network first – find out how to do this by referring to point 6.4.3. Once the monitor is connected to the internet, it can not be configured or operated.
English 6.3 Event list All the recordings are displayed in the event list and are sorted according to the date. c d h e f g 6.3.1 List of recordings Press the date with the green background to go to the list of recordings. The recordings are saved to subfolders which are named with the date on which the recording was made. The recordings are saved as individual files with the duration of the recording being used as the file name. V i k j 6.3.
English Explanation of symbols c Live view Change to live view d Back Back to the main menu e Camera Select one of the numbered cameras to view the recordings. Select the camera with “A” to view the recordings of all the cameras. f Weekday Here you see the weekday g Day A field with a green background means that a recording is available on this day. Press it to go to the “List of recordings”. h Change month Press the arrow buttons to change between months.
English 6.4 Settings At the “Settings” menu item you can select the following items: 6.4.1 Camera settings c d e c Selecting cameras to pair 1. Select the required camera (1-4). The system counts down from 60 seconds. 2. During the 60 seconds, press the PAIRING button on the camera cable until the green LINK LED on the front of the camera starts flashing. The LINK LED is lit up continuously once the connection is established.
English d Displaying/concealing a camera Use the 9 buttons to display a camera or press the 8 button to conceal it. If you have not trained all four cameras, conceal the other cameras. e Camera brightness Select the required brightness from between -2 (dark) to 2 (bright). 6.4.
English c Motion detection Here you can set the sensitivity of the motion detection for each camera. You can choose between “Low”, “High” and “Off”. High: Motion detection with high sensitivity Low: Motion detection with low sensitivity Off: Motion detection is off. Motion is not recorded. d Alarm alerts via email You can have an alarm alert sent to you via email as soon as the camera detects any motion. Proceed as follows: 1. Select “active”.
English e Timer recordings You can save a recording time to start recording at a very specific time. You can save up to 5 recording procedures. 1. First select the number of the camera. 2. Set the start and stop time. To do this use the arrow buttons. 3. Select the required date from the calendar. 4. Press “Save” to save the procedure or “Delete” to reset. 5. As soon as a timed recording has been saved, the symbol for recording appears. 6.4.
English d Securitycode The standard security code is: 123456 For reasons of security, change this code and enter a new password (max. 8 digits). Press the field with the white background and a keyboard appears. Then confirm with “OK”. You will need the security code later if you want to access the cameras via the app. e Network information Here you can find out details about the active network. You will need to enter the DID code for the app later.
English 6.4.4 Alarm settings c c d Duration Here you can select the required duration of the alarm. You can set the alarm duration individually: 2 seconds, 10 seconds, 30 seconds or no sound. Press any button to switch off the alarm in the event of an alarm. d Alarm sounds You can choose between three alarm sounds.
English 6.4.5 System settings d c e f h g c Energy saving mode Here you can activate or deactivate the automatic screen switch-off after 2 minutes. If the energy saving mode is activated, your battery lasts roughly half an hour longer. d Automatic lock If the automatic lock is activated, the monitor no longer responds to the touch function after a few minutes. Press the “Power” button to switch on the monitor again.
English Setting the time // date Here you can set the date and time. Then save your entries. Note: AM = 00:00 – 11:59 PM = 12:00 – 23:59 Saving the time // timer You have the option of programming a timer / countdown. Press the arrow buttons to set the time. After confirming with “Start”, the timer counts down and rings once the time has elapsed, then the following symbol appears. Press on “OK” to stop the alarm.
English g Updating the system Always use the latest system firmware. You can download the latest version from our website at www.abus.com (item number TVAC16000B). To download, please proceed as follows: 1. Remove the SD card from your monitor and insert it in a SD card reader which is connected to your computer. 2. Unzip the folder. Save the files from the folder to the SD card. 3. Remove the SD card again from the SD card reader and put it back into the monitor. 4.
English 7. Remote access via app This 7" touch screen wireless monitor gives you the option of switching live to your cameras. The app for this device can be found in the App Store under the name of “TVAC16000”.
English g Connection status If you have added you system successfully, the name of your system and the current connection status appear. Click on the screen to go to the live view. System name e.g. System 1 Connection status Connected = you are connected with your system Disconnected = there is no connection to the system Adding the system Here you can add an additional system System information Go to the system information here.
English i Saving the PIN code If you want to save a PIN code for this APP, proceed as follows: 1. Open the “Setup PIN Lock” at 2. Enter a 4-digit PIN code and repeat it. 3. Put a tick at “Enable lock when starting”. When you have saved a PIN code, it will be requested when you want to open the app. 8. Maintenance and cleaning 8.1 Maintenance Regularly check the technical safety of the product, e.g. check the housing for damage.
English 10. Technical data Number of IR LEDs Rechargeable battery running time Battery type Resolution Image sensor Angle of view Frequency Wireless range IR swivel filter Camera inputs Max. operating temperature Modulation Monitor Network access Lens Range of night vision function IP protection class Transmission power Sensitivity DC voltage supply Storage medium OSD language Power consumption Certifications Camera 25 7" monitor - - 1.5 hours Li-Ion polymer battery, 3.
