Absco Regent Shed Assembly Instructions Model: J30372R INSTRUCTIONAL VIDEOS CONCRETE SLAB WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 1in DEEP AROUND THE PERIMETER CHANNEL T RE E REBATED EDGE THIS WILL HELP WATER EGRESS FROM THE BASE OF THE SHED NC CO AB SL CONCRETE SLAB 3in WIDE REBATE We thank you for choosing an Australian made shed. For further assistance please visit our detailed instructional video library at www.abscosheds.com.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on the following pages. SITE PREPARATION The site for the shed must be level.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION STEEL SHEET 2 PART CHECK QTY No. STEEL SHEET 2 STEEL SHEET 2 4 STEEL SHEET 32A 31A 1 STEEL SHEET A STEEL SHEET 44L 1 B GABLE R/H 44R 2 STEEL SHEET 6 PART CHECK No.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 4 COMPONENT DESCRIPTION PART No. 91A Part No. Here COMPONENT DESCRIPTION CHECK QTY 2 PART No. CHECK 89A Part No. Here JAMB 5ft-10-9/32in (L) 1 89C Part No. Here 1 90A Part No.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 12 COMPONENT DESCRIPTION CHANNEL JOINER 7-7/8in (L) PART No.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = CSJ = JOIN>> JOIN>> <> STEP 2. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS STEP 1.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2in OVERLAP OF THE RIDGE CAP 2" 2in STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 8-55/64in IN EACH RIDGE CAP. 2" 2in PLACE TEK SCREWS IN 2in INCREMENTS FROM SAID END.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = 1 TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW QTY. = 2 PARTS 97DL & 97DR QTY. = 1 PART ZARSP - 5-23/32in in 5/8 DR 97 ZARSP / 7-7 8in DL 97 in 5/8 D) 7 T9 R (PA ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30372R 19/06/15 THE TOP SECTIONS OF CAPPING WILL OVERLAP EACH OTHER AT THE JOIN BY 2.0in. THIS MAY VARY SO ENSURE THAT THE OVERALL LENGTH IS CORRECT FIRST.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30372R 19/06/15 TOLL FREE HELP - 800-305-4436 VIEW OF ROOF COMPONENTS Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS PAGE 10
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30372R 19/06/15 VIEW OF WALL COMPONENTS TOLL FREE HELP - 800-305-4436 Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS PAGE 11
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners . To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 1. REAR PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN 30A 31A 77B 31A 30A 81B ATTACH 77B CHANNEL WITH NOTCHED END AS SHOWN 2.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 3. ROOF PANEL ASSEMBLY (2 Required) 44R LAY SHEETS OUT AS SHOWN 45A 45A 45A 44L 87B 2 x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO. 81L FITTED 62B 81L 87B ATTACH LIPS 87B AS SHOWN. LIPS SHOULD OVERLAP ROOF CHANNELS 81L AND 62B.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 4. DOOR DOOR PANEL PANEL ASSEMBLY ASSEMBLY 58C ATTACH 58C CHANNELS AS DESCRIBED ON PAGE 12 58C 58A 58B B 12A A 58C 89C ATTACH 89C WITH COLORED SIDE FACING OUT.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 89A 5. FRONT PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN 34A 89A 34A NOTCH ON JAMB 90A FITS OVER JAMB 89A AND 89B AND NOTCH ON 89B AND 89A FITS OVER 77A A 77 89 A A 90 DO NOT INSTALL THIS SCREW (OR THE TOP EQUIVALENT) UNTIL CHANNELS 77A AND 55C ARE INSTALLED 77A 90A 79A 55C A 77 A 89 A 79 C 55 NOTCH ON JAMB 89A AND 89B FITS OVER CHANNEL 55C AND CHANNEL 79A INSERTS INTO 55C WITH SHORTEST SIDE FACING OUT.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 6. DOOR PANEL ASSEMBLY 91A 91A INSERT 91A JAMBS UNDER THE CHANNELS AROUND THE DOOR B A NOTE: 8/32in CSK Nuts and bolts (supplied) will require enlarging the hinge hole using a 11/64in drill bit USE 4 x 8/32in NYLOC BOLTS TO SECURE PADBOLT TO DOOR NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS 7. PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. the top channel of each panel is pre-punched for attaching roof sheets, the bottom channels are not.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS ROOF CONSTRUCTION OUTSIDE VIEW INSIDE VIEW SECURE RIDGE BEAM TO GABLE SECTIONS WITH TWO SCREWS AT EACH END. SECURE EACH ROOF PANEL WITH ONE SCREW IN EACH CORNER ONLY AT THIS STAGE ROOR OVERHANGS ALL WALL PANELS INSIDE VIEW 13A ABSCO INDUSTRIES AFTER ATTACHING BOTH ROOF PANELS TO WALLS AS SHOWN ABOVE, FIT ONE REGENT BRACE TO THE RIDGE BEAM AND FRONT WALL AS SHOWN. YOU WILL HAVE TO REMOVE AND REPLACE EXISTING SCREWS AT FIXING LOCATIONS.
Absco Regent Shed Model: J30372R INSTRUCTIONAL VIDEOS FINAL CONSTRUCTION 14A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP CHANNEL AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF 16 CONCRETE ANCHORS BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE WALL SHEET STEEL ANGLE SLAB - DRILL A 25/64in HOLE INTO THE WALL SHEET - DRILL A 25/64in HOLE INTO THE CONCRETE ABSCO INDUSTRIES ASSEMBLY INSTRUCTIO
