Premier Garden Shed Assembly Instructions Model: J30232G INSTRUCTIONAL VIDEOS FRONT BASE LENGTH: 9ft-10-7⁄64in SIDE BASE LENGTH: 7ft-4-31⁄32in HEIGHT: 6ft-10-43⁄64in CONC 7ft -8- 29 RETE SLAB 3⁄64in 10ft-2- ⁄32 in WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 1in DEEP AROUND THE PERIMETER CHANNEL RE NC CO AB SL TE REBATED EDGE THIS WILL HELP WATER EGRESS FROM THE BASE OF THE SHED CONCRETE SLAB 3in WIDE REBATE We thank you for choosing an Australian made shed.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS GENERAL INSTRUCTIONS · Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. · Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four. SITE PREPARATION · The site for the shed must be level.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION 2 2 1 1 8 2 2 2 STEEL SHEET 30A 2 31A 1 A 1 B 4 49A 4 36L 2 36R 2 42D 220 STEEL SHEET STEEL SHEET STEEL SHEET STEEL SHEET STEEL SHEET STEEL SHEET STEEL SHEET PART CHECK No. COMPONENT DESCRIPTION PART CHECK QTY No. STEEL SHEET 34A 90A Part No. Here 89C Part No. Here 91A Part No. Here 86A A 86 LIP TRIM 15A PEAK BRACE 89A Part No.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS COMPONENTS - SPLICED CHANNEL & RIDGE BEAM QTY 10 COMPONENT DESCRIPTION PART No.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS FULL LENGTH CHANNELS & ACCESSORIES COMPONENT DESCRIPTION QTY 1 2 1 A 79 CHANNEL A 58 CHANNEL WITH HINGES B 58 CHANNEL 220 8 PART No. CHECK QTY 79A 2 58A 2 58B 4 SELF DRILLING HEX HEAD TEK SCREWS (NO HOLE REQUIRED) 2 8 2 12 8/32in CSK SCREW & NUT SECURE HINGES TO DOOR 1 1 2 ABSCO INDUSTRIES PART CHECK No.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = CSJ = JOIN>> JOIN>> <> STEP 1. STEP 2. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS STEP 1.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2in OVERLAP OF THE RIDGE CAP 2" STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 8-55/64in IN EACH RIDGE CAP. 4 8-55⁄6 in 2in PLACE TEK SCREWS IN 2in INCREMENTS FROM SAID END.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = 1 TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW QTY. = 2 PUSH PUSH QTY. = 1 PARTS 97AL & 97AR n i 5/8 AR 97 ZARSP n /8i 7 7 AL 97 THE TOP SECTIONS OF CAPPING WILL OVERLAP EACH OTHER AT THE JOIN BY 2in.
ABSCO INDUSTRIES 86A NO.
36L ABSCO INDUSTRIES 31A 36R 83R 31A ASSEMBLY INSTRUCTION - MODEL: J30232G 14/08/14 42D 30A VIEW OF WALL COMPONENTS 81C 83L 55B 30A 34A 90A 55C 91A 89A 79A 91A 42D 83R 81C 89A 36R CUSTOMER SUPPORT - 800-305-4436 81B Premier GardenShed Model: J30232G 34A A 36L 15A B 83L 55A PAGE 11 INSTRUCTIONAL VIDEOS
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners . SN AP TT i E To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS 1. REAR PANEL ASSEMBLY LAY SHEETS OUT AS SHOWN 30A 31A 55B 31A E APT iT SN 30A 81B E APT iT SN ATTACH 55B AND 81B CHANNEL WITH NOTCHED END AS SHOWN INSTALL PEAK BRACE WITH OVERHANG FITTING INSIDE SHED 2.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS 3. ROOF PANEL ASSEMBLY (2 Required) LAY SHEETS OUT AS SHOWN 86A 49A 60A 2 x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO. 81A FITTED 49A E APT iT SN 49A 49A 81A E APT iT SN 86A ATTACH LIPS 86A AS SHOWN. LIPS SHOULD OVERLAP ROOF CHANNEL 81A AND 60A.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS 4. DOOR PANEL ASSEMBLY 58C ATTACH 58C CHANNELS AS DESCRIBED ON PAGE 12 SNAPT iTE 58C SNAPT iTE 58A 58B B 12A A SNAPT iTE 89C 58A 58C ATTACH 89C WITH COLORED SIDE FACING OUT.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS 89A 5.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS 6. DOOR PANEL ASSEMBLY 91A 91A INSERT 91A JAMBS UNDER THE CHANNELS AROUND THE DOOR B A NOTE: 8/32in CSK Nuts and bolts (supplied) will require enlarging the hinge hole using a 11/64in drill bit USE 4 x 8/32in BOLTS AND NYLOC NUTS TO SECURE PADBOLT TO DOOR NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS NO PADBOLT HASP REQUIRED AT TOP 7. PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. the top channel of each panel is pre-punched for attaching roof sheets to, the bottom channels are not.
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS ROOF CONSTRUCTION Slide the roof panel into position, and secure with one screw at each corner only at this stage ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 14/08/14 Secure peak brace to ridge beam and roof panel with one screw at each end Move the other roof panel into position and secure peak brace to ridge beam and roof panel with one screw at each end CUSTOMER SUPPORT - 800-305-4436 PAGE 19
Premier Garden Shed - Model: J30232G INSTRUCTIONAL VIDEOS FINAL CONSTRUCTION 14A Bend the top and bottom flanges as shown, then hook the bottom flanges under the top channel and screw the top flanges for both as shown gable caps ANCHORING OF SHED LOCATION OF 12 CONCRETE ANCHORS BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 25/64in HOLE INTO THE WALL SHEET - DRILL A 25/64in HOLE INTO THE CONCRETE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 14/08/14
