Absco Space Saver Shed Assembly Instructions Model: 23081S FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH: 0.75m FRONT WALL HEIGHT: 1.95m REAR WALL HEIGHT: 2.08m RETE CONC 88 SLAB m 0m m 2360m WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 10mm. 50mm 10mm 50 mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosing an Australian Made Shed. For further assistance please visit our detailed instructional video library at http://www.absco.com.
Absco Space Saver Shed Model: 23081S GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four. SITE PREPARATION The site for the shed must be level.
Absco Space Saver Shed Model: 23081S COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART CHECK QTY No.
Absco Space Saver Shed Model: 23081S COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 2 1 2 COMPONENT DESCRIPTION PART No. CHANNEL WITH HINGES L = 1725mm 58A COMPONENT DESCRIPTION 1 PART No.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 VIEW OF ROOF COMPONENTS Absco Space Saver Shed Model: 23081S PAGE 5
ABSCO INDUSTRIES VIEW OF WALL COMPONENTS ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 Absco Space Saver Shed Model: 23081S PAGE 6
Absco Space Saver Shed Model: 23081S ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks all perimeter channels to all roof and wall sheets without the need for tools and fasteners . To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Absco Space Saver Shed Model: 23081S DOOR PANEL ASSEMBLY 58C 58A B 58B 12A 58C 20mm FLANGE 15mm FLANGE B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 PAGE 8
Absco Space Saver Shed Model: 23081S REAR PANEL ASSEMBLY 43B 43C 43B 54B 81D ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 PAGE 9
Absco Space Saver Shed Model: 23081S SIDE PANEL ASSEMBLY (TWO REQUIRED) 61B X4R X4L 81J ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 PAGE 10
Absco Space Saver Shed Model: 23081S ROOF PANEL ASSEMBLY 43D 43D 43D 81C 88B 81C 88B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 PAGE 11
Absco Space Saver Shed Model: 23081S FRONT PANEL ASSEMBLY 89A 89B 32A 32A 54A 90B 79B 54C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 PAGE 12
Absco Space Saver Shed Model: 23081S 91A 91A B B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment.
Absco Space Saver Shed Model: 23081S PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. The top channel of each panel is pre-punched for attaching roof sheet. The base channels are not pre-punched.
Absco Space Saver Shed Model: 23081S FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS WALL SHEET BOLT & NUT - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE STEEL ANGLE SLAB - DRILL A 10mm HOLE INTO THE WALL SHEET - DRILL A 10mm HOLE INTO THE CONCRETE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 23081S 26/11/10 DYNABOLT PAGE 15
PRODUCT WARRANTY Congratulations on your purchase of an ABSCO Product. ABSCO SHEDS are made using high quality Bluescope™ Australian made Zincalume™ or Colorbond Steel™. We are pleased to advise we warrant that this steel will not rust, crack, flake peel or blister for 20 years from date of purchase.
ABSCO STEEL BUILDINGS- STORAGE GUIDELINES ABSCO steel buildings include garden sheds, storage units, aviaries, garages and carports. ABSCO steel buildings are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry.
