ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H ‘Config A’ shown LAB ES T CRE N CO ” 122 63.8” This shed kit can be built two ways! Choose roof slope direction to suit your site. Config A Config B Please make a decision now and read ahead to get a good understanding of the steps required before beginning contruction.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H Australian Made GENERAL INSTRUCTIONS SAFETY NOTES • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H COMPONENTS LIST QTY Nominal sheet widths are shown +/- 1/8” is within tolerance DESCRIPTION PART # CHK QTY DESCRIPTION PART # 2 STEEL SHEET 80” x 30.4” H31 2 STEEL SHEET 70.3” x 30.4” 31A 1 STEEL SHEET 80” x 30.4” H3L 1 STEEL SHEET 70.3” x 28” 34A 1 STEEL SHEET 80” x 30.4” H3R 1 STEEL SHEET DOOR 67.9” x 30.4” B 3 STEEL SHEET 70.3” x 30.4” 30A 4 STEEL SHEET 63.4” x 30.4” 43S 1 STEEL SHEET 70.3” x 30.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H COMPONENTS LIST QTY DESCRIPTION PART # CHK QTY DESCRIPTION PART # 4 CHANNEL 59” 81BL 4 CHANNEL 81BR 59” 2 CHANNEL 59” 81AL 2 CHANNEL 81AR 59” 1 CHANNEL 59.5” 77E 1 CHANNEL 59.5” 77J 1 CHANNEL 59.5” 77G 1 CHANNEL 59.5” 77K 1 CHANNEL 70.3” 80A 1 CHANNEL 67.9” 58A 2 CHANNEL 30.4” 58C 1 CHANNEL 67.9” 58B 1 CHANNEL 30.7” 79C 1 JAMB 70.3” 89A 1 JAMB 30.7” 90C 1 JAMB 70.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H SNAPTiTE ASSEMBLY GUIDE The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners. To assemble each panel, the perimeter channels are secured to the top and bottom of each panel. Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet. Each perimeter channel must finish flush with the edges of the sheets.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H Guide on Joining Spliced Channels The text marked on all parts must be shown on the same side as each other = = = = CSJ = JOIN>> <> JOIN>> JO IN Step 2.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H PRE-ASSEMBLY OF SPLICED CHANNELS Join together 12 x channel sections using 6 x channel joiners (Part CSJ) NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them. = 2x 81A .8” AR 81 7 11 = 4x 81B AL 81 BR 81 2x 81AL 2x 81AR BL 81 4x 81BL 4x 81BR Absco Industries Assembly Instruction Manual Model: 15301NK-PTX 23/11/23 1.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H REAR PANEL ASSEMBLY 1x required. Ed ge ho les thi 1. Overlap two 30A sheets by one rib as shown. ss ide 30A Turn one sheet so edge holes are to the outside as pictured. 30A Ed ge ho les thi ss ide 2. Fasten with 3/8” self tapping screws FAST001 through prepunched sheet-to-sheet holes on overlap. rst re flu n ke c he a ds fi sh If you can’t see bottom hole twist the sheet left or right.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H ROOF PANEL ASSEMBLY 1x required. 1. Layout and overlap sheets by one rib as shown. 43S 43S 2. Use 4x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes. 43S 43S 3. Attach the front and rear channels using the SNAP-TiTE method. Make sure you have the shorter, 0.6” side of the channel to the top of the sheeting 81A SN E APT iT 0.6 81A P TE NA T i S 4. 0.8 88J 4.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H 6’8” H SIDE PANEL 1x required. Ed ge H3R ho les thi 1. Layout and overlap sheets by one rib as shown. Orientate outside sheets as pictured. ss ide H31 2. Use 3x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes. H31 H3L Ed ge ho les thi ss ide 3. Attach the top and bottom channels using the SNAP-TiTE method. E APT iT 81B Make sure you have the shorter, 0.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H 4x 5’11” H SIDE PANEL ed ge 1x required. ho les 30A thi ss ide 1. Layout and overlap sheets by one rib as shown. Orientate outer sheets with holes to the outside as pictured. 31A 2. Use 2x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes. 31A 4x top 30G ho les 15 thi 3. Attach the top and bottom channels using the SNAP-TiTE method. ss ide Make sure you have the shorter, 0.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H DOOR PANEL ASSEMBLY 1. Position the DoorB sheet as shown and attach the top and bottom channels using the SNAP-TiTE method. 1x required. 58C Make sure you have the shorter, 0.6” side of the channel to the exterior side of the sheeting B 0.6 58C 0.8 2. Insert the two vertical channels 58A 58B Make sure the longer, 0.8” side of the channel to the exterior. side of the sheet. Insert the 0.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H DOOR PANEL ASSEMBLY CONTINUED 8. Turn the door over as shown. 91A 91As overlap here 91A of de anel i s In r p o do 9. Now we’ll fit the two 91A jamb door braces. Align the holes in the brace with holes in the door. 91A Make sure to tuck both ends of the brace into the channels that frame the door. Fasten from beneath with five self tapping screws FAST001.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H FRONT PANEL 1x required. his 4x e dg t les 1. Orientate the 34A sheet as shown and place the 89A jamb on top. e sid ho e 34A 89A 89A SN AP TT i E 77J les o eh s he nt g Ali SN AP TT i E 2. Use 2x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes in the parts. Only do the two shown for now. 3. Attach the channels using the SNAP-TiTE method. Make sure you have the shorter, 0.
5’ W x 10’ D x 6’10” H Config A ABSCO NARROW SHED MODEL: 15301NK-PTX ATTENTION! The following pages show how to build the ‘Config A’ version of the shed as pictured. Config is listed on each page here If you would like to build ‘Config B’ go to page 20. FRONT PANEL ASSEMBLY CONTINUED les Ja es h nt g Ali o eh Ja 90C mb s sid lots ej am over b mb top goe ch s ins an ne ide l 5. Next is the top-of-doorway jamb.
5’ W x 10’ D x 6’10” H Config A ABSCO NARROW SHED MODEL: 15301NK-PTX ATTACH GABLE PANELS FRONT PANEL ASSEMBLY CONTINUED 7. Turn the front panel over. 8. Take the 16L gable panel and align the hole pattern with the interior side of the 77J channel. 16L D D 9 77J Fasten with three self tapping screws FAST001 that align with existing holes in the channel The two ‘D‘ screws don’t have channel holes, but fix through as well. In fro side nt o pa f ne l 9.
5’ W x 10’ D x 6’10” H ATTACH DOOR TO FRONT PANEL Config A ABSCO NARROW SHED MODEL: 15301NK-PTX 1. Use the supplied 1/8” drill bit DRILL and go through these existing jamb holes and into the sheet behind. In do side or pa of ne l Fro nt pa 2. Lay the door in the open position so the hinges dangle over their matching holes. ne l Align and use a pop riveter and three FAST009 rivets per hinge six rivets total.
5’ W x 10’ D x 6’10” H PANEL CONSTRUCTION 1. Start with the front panel, open the door to help stand it up. e Sid 2. Attach the 5’11” H side panel next. Sit the side wall channel inside the end wall channels as shown below. Fro nt Align the holes in the 80A channel with those in the front panel 89B jamb 4 In rea side r p of an el Fro Fasten with four longer 3/4” self tapping screw FAST013. 3.
5’ W x 10’ D x 6’10” H 7 5. Square up the shed walls. Make sure they’re straight and check opposite corner-to-corner dimensions are equal. FINAL CONSTRUCTION 6 6. Safely place roof panel on top and align roof sheet holes with channels of the side walls and fix with a 3/8” self tapping screws FAST001 at each hole. Check roof lips sit nicely at front and rear walls first. 6 7 Config A ABSCO NARROW SHED MODEL: 15301NK-PTX 7.
5’ W x 10’ D x 6’10” H The following pages show how to build the ‘Config B’ version of the shed as pictured. If you would like to build ‘Config A’ go back to page 15. Config is listed on each page here NOTE: Orientate panel so door opening is on the left as pictured. FRONT PANEL ASSEMBLY CONTINUED Ali gn 90C er Config B ABSCO NARROW SHED MODEL: 15301NK-PTX ov ts o l b b s jam m e a J sid the se ho les 5.
5’ W x 10’ D x 6’10” H Config B ABSCO NARROW SHED MODEL: 15301NK-PTX ATTACH GABLE PANELS FRONT PANEL ASSEMBLY CONTINUED 7. Turn the front panel over. 8. Take the 16R gable panel and align the hole pattern with the interior side of the 77E channel. Fasten with three self tapping screws FAST001 that align with existing holes in the channel 16R D The two ‘D‘ screws don’t have channel holes, but fix through as well. 77E D f e o el d i Ins t pan n fro 9 9.
5’ W x 10’ D x 6’10” H ATTACH DOOR TO FRONT PANEL Config B ABSCO NARROW SHED MODEL: 15301NK-PTX 1. Use the supplied 1/8” drill bit DRILL and go through these existing jamb holes and into the sheet behind. do Insid or e o pa f ne l a tp n Fro l ne 2. Lay the door in the open position so the hinges dangle over their matching holes. Align and use a pop riveter and three FAST009 rivets per hinge six rivets total.
5’ W x 10’ D x 6’10” H PANEL CONSTRUCTION Config B ABSCO NARROW SHED MODEL: 15301NK-PTX 1. Start with the front panel, open the door to help stand it up. ar Re 2. Attach the 5’11” H side panel next. Sit the side wall channel inside the end wall channels as shown below. Sid e Align the holes in the 80A channel with those in the front panel 89B jamb 4 of de nel i s In r pa rea Fasten with four longer 3/4” self tapping screw FAST013. Ins 6’8 ide o ”H f 3.
5’ W x 10’ D x 6’10” H Config B ABSCO NARROW SHED MODEL: 15301NK-PTX 5. Square up the shed walls. Make sure they’re straight and check opposite corner-to-corner dimensions are equal. FINAL CONSTRUCTION 6 7 6 7 6. Safely place roof panel on top and align roof sheet holes with channels of the side walls and fix with a 3/8” self tapping screws FAST001 at each hole. Check roof lips sit nicely at front and rear walls first. 7.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.
ABSCO NARROW SHED MODEL: 15301NK-PTX 5’ W x 10’ D x 6’10” H Absco Sheds Storage Guidelines • Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
