Absco Industries Bike Shed Model: 23083XK-PTX FRONT BASE LENGTH: 7' 5 " 2' 6 ABSCO INDUSTRIES SIDE BASE LENGTH: 2' 6 11/16" 7/1 6" ASSEMBLY INSTRUCTION MANUAL t) Fron "( /16 1 '31 )7 ack " (B /16 11 7' 4 HEIGHT: 3' 9 1/4" MODEL: 23083XK-PTX 17/07/19 1
Absco Industries Bike Shed Model: 23083XK-PTX GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages. SITE PREPARATION The site for the shed must be level. An uneven surface may result in misalignment of parts.
Absco Industries Bike Shed Model: 23083XK-PTX SPLIT SHEET 39B INTO 2x 1' 15/16" WIDE SHEETS This shed comes with a perforated sheet 39C that is designed to be split into two smaller sheets (39C) SPLITTING SHEET 39C COMPONENT DESCRIPTION QTY STEEL SHEET 3' 8 1/2" LONG 2' 6 7/16" WIDE 1 PART No. 39C QTY = COMPONENT DESCRIPTION PART No. STEEL SHEET 3' 8 1/2" LONG 1' 15/16" WIDE 39C 2 THESE SHEETS HAVE SHARP EDGES. ONCE SEPARATED PLEASE USE APPROPRIATE FOOT AND HAND PROTECTION WHEN HANDLING.
Absco Industries Bike Shed Model: 23083XK-PTX COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS MAIN PACK CARTON QTY DESCRIPTION PART # CHK QTY 2 STEEL SHEET 3' 8 1/2" LONG 2' 6 7/16" WIDE 44Z 2 1 STEEL SHEET 2' 6 7/8" LONG 2' 6 7/16" WIDE 43W 1 1 1 STEEL SHEET 2' 6 7/8" LONG 2' 6 7/16" WIDE 43X 1 STEEL SHEET 2' 6 7/8" LONG 2' 6 7/16" WIDE 43Y 1 ANCHORS 4 PACK ANCHORSET4 DESCRIPTION PART # STEEL SHEET 3' 8 1/2" LONG 2' 6 7/16" WIDE 44W STEEL SHEET 3' 8 1/2" LONG 1' 15/16" WIDE 39
Absco Industries Bike Shed Model: 23083XK-PTX COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS 23083BSM CHANNEL PACK QTY 1 1 1 2 1 1 4 1 2 1 1 2 1 2 DESCRIPTION PART # CHK QTY CHANNEL 3' 8 3/8" 54PL 1 CHANNEL 3' 8 7/16" 54SL 1 CHANNEL 3' 8 7/16" 54TL 1 CHANNEL 3' 7 7/8" 54RL CHANNEL 3' 8 3/8" 81DL 1 CHANNEL 1' 3 7/16" 79AL CHANNEL 2' 6 7/16" DESCRIPTION PART # CHANNEL 3' 8 3/8" 54PR CHANNEL 3' 8 7/16" 54SR CHANNEL 3' 8 7/16" 54TR CHANNEL 3' 7 7/8" 54RR CHANNEL 3' 8 3/8" 8
Premier GardenAbsco ShedIndustries - Model: J30232G Bike Shed Model: 23083XK-PTX INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> JOIN>> <> J STEP 1. STEP 2. Position the channels and the CSJ joiner channel so the center of the CSJ is in line with the end of each channel to be joined together.
Absco Industries Bike Shed Model: 23083XK-PTX PRE-ASSEMBLY: JOINING SPLICED CHANNELS NOTE: JOIN TOGETHER 12 X CHANNEL SECTIONS USING 6 X CHANNEL JOINERS (PART CSJ) NOTE: SOME CHANNELS HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY CHANNEL WHERE THE CSJ JOINING CHANNEL COVERS HOLES ON THE CHANNELS YOU ARE CONNECTING 7' 4 = 1 x 54T 6" /1 15 TL 54 = 1 x 54S SL 54 TR 54 1 X 54TR 1 X 54TL = 1 x 81D SR 6" 54 '4 7 1 X 54SR 1 X 54SL /1 11 DL 81 PL 54 = 2 x 54R DR 81 1 X 81DR 1
Earthcore Garden Shed Absco Industries Bike Shed Model:23083BSM 23083XK-PTX Model: VIEW OF WALL COMPONENTS 61G 88Z 44W 54P 44Z 91K 44Y 44Z 61G 88Z 54R 39C 81J R 90A 44W 54R L 39C 91K 81J 79A VIEW OF LID COMPONENTS 87H 54S 43W 43X 54T 43Y NO.
Premier Garden Shed Absco Industries Bike Shed Model: 23083XK-PTX Model: 30152GK INSTRUCTIONS AND VIDEOS ABSCO ASSEMBLY INTRODUCTION The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners. SN AP TT i E To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.
Earthcore Garden Shed Absco Industries Bike Shed Model:23083BSM 23083XK-PTX Model: REAR PANEL ASSEMBLY 44Z 44Y 44Z E APT iT SN 54P 81D E APT iT SN FAST012A FAST009 ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL MODEL: 23083XK-PTX 17/07/19 10
Absco Industries Earthcore Garden Shed Bike Shed Model:23083BSM 23083XK-PTX Model: SIDE PANEL ASSEMBLIES Top E APT iT SN 61G Top E APT iT SN 44W 61G 44W Bottom P TE NA T i 81J S 81J Bottom ABSCO INDUSTRIES E APT iT SN ASSEMBLY INSTRUCTION MANUAL MODEL: 23083XK-PTX 17/07/19 11
Absco Industries Earthcore Garden Shed Bike ShedModel: Model:23083BSM 23083XK-PTX LID ASSEMBLY 87H 43W 43X 87H NOTE: HOLE ORIENTATION ON SHEETS ILLUSTRATED 43Y E APT iT SN D 54S E APT iT D SN 54T 91L 91L TIP: Fasten 1x screw at each end of each 91L from the underside of the lid. Flip over the lid and fit the remaining screws. The screws at the ends can then be removed and fastened from the top side of the lid.
Absco Industries Bike Shed Model: 23083XK-PTX LID ASSEMBLY 1 27/64” 3 1/4” A SINGLE PADBOLT IS TO BE FIXED TO THE UNDERSIDE OF THE LID. THE MIDDLE OF THE PADBOLT IS TO BE 1 27/64” TO THE RIGHT OF THE CENTRELINE OF THE LID. THE BOLT IS ORIENTATED AS PICTURED. THE CLOSEST PAIR OF HOLES ARE 3 1/4” FROM THE EDGE OF THE LID. USING THE PADBOLT AS A TEMPLATE MARK THE FOUR HOLES AS SHOWN AND DRILL USING A 15/64” DRILL BIT.
Absco Industries Bike Shed Model: 23083XK-PTX LID ASSEMBLY D 91J D 58T D D L D D D 58Y 58Y D D D D R D CO12A D D D 58W D D 58C E APT iT 58C SN D ALL VERTICAL DOOR CHANNELS ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR CHANNELS L D D 58C E APT iT E APT iT SN SN 58C R CO12A FAST006 E APT iT SN ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL MODEL: 23083XK-PTX 17/07/19 14
Absco Industries Bike Shed Model: 23083XK-PTX DOOR PANEL ASSEMBLY FAST005 8x D D D FAST006 FAST009 3x FIT FAST001 SCREWS TO ENDS OF 91A, FLIP PANEL OVER & FIT REMAINING SCREWS THROUGH FRONT, THEN FLIP BACK AND REFIT END SCREWS THROUGH FRONT FAST012A 91A FAST004 4x D DD 58Y R E SID IN OF O DO FAST001 4x L TOP 91S FAST001 2x FAST006 TOP FAST001 5x IN D SID D D EO R FD FAST009 FAST001 4x OO R 58Y D ABSCO INDUSTRIES D D FAST001 5x (2x DRILL) ASSEMBLY INSTRUCTION MANUAL MODEL
Absco Industries Bike Shed Model: 23083XK-PTX FRONT PANEL ASSEMBLY NOTE: FIT FAST001 SCREWS THROUGH 54R CHANNELS AT TOP AND BOTTOM OF 39C SHEETS 1ST THEN SQUEEZE 91K JAMBS INTO POSITION AND SECURE IN NEXT STEP BELOW 54R E APT iT FAST001 SN 39C D 91K FAST001 D D FAST001 4x P TE NA T i S D D 91K D FAST001 E APT iT SN D FAST001 4x 54R D 39C FAST001 E APT iT SN D FAST001 10x 90AR FAST001 4x D 90AL 79AL D FAST001 10x 79AR FAST001 4x D ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MA
Earthcore Garden Shed Absco Industries Bike Shed Model:23083BSM 23083XK-PTX Model: FRONT PANEL DOOR ASSEMBLY NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 5/32” DRILL BIT D D D FAST009 FAST009 FAST009 R FAST009 FAST009 FAST009 D FAST009 D FAST009 FAST009 D FAST009 FAST009 FAST009 D D D L D D D NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for prop
Earthcore Garden Shed Absco Industries Bike Shed Model:23083BSM 23083XK-PTX Model: WALL PANEL CONSTRUCTION FAST009 FIT 4x FAST001 SCREW AT EACH CORNER FAST009 SIDE WALL PANEL CHANNELS FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL CHANNELS EARTHCORE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL ASSEMBLY INSTRUCTION MANUAL MODEL: 23083BSM 15-05-2018 MODEL: 23083XK-PTX PAGE 17 17/07/19 18
Earthcore Garden Shed Absco Industries Bike Shed Model:23083BSM 23083XK-PTX Model: LID PANEL INSTALLATION FAST009 FAST009 FAST009 9/16” 13/16” 88Z - USE THE 3mm DRILL BIT TO DRILL 1x HOLE THROUGH THE 88Z LIP AS ILLUSTRATED - DRILL ANOTHER HOLE THROUGH THE OPPOSITE END OF THE OTHER 88Z LIP AS ILLUSTRATED 61G - FIT THE 88Z LIP TO THE FRONT OF THE 61G CHANNEL USING 1x SCREW ONLY 13/16” 9/16” 88Z 61G - FIT THE OTHER 88Z LIP TO THE FRONT OF THE OPPOSITE 61G CHANNEL USING 1x SCREW ONLY - THE 88Z LIPS AR
Absco Industries Bike Shed Model: 23083XK-PTX FINAL CONSTRUCTION AFTER FINAL ALIGNMENT AND ANCHORING HAS BEEN COMPLETED. CLOSE THE LID AND EXTEND THE LID PADBOLT UNTIL IT CONTACTS THE FRONT CHANNEL. MARK THIS CENTREPOINT AND DRILL A 10MM HOLE. TIP: IT’S EASIER TO DRILL A 13/32” HOLE IN METAL WHEN A SMALL DRILL BIT IS USED FIRST.
Absco Industries Bike Shed Model: 23083XK-PTX EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.
