ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H 30 .7” AU: 1800 029 701 +1 (866) 788 3046 +1 (866) 788 3046 N Z: 0800 466 444 Absco Industries ” 42.5 admin@absco.com.au admin@absco.com.au www.abscogardensheds.com www.abscosheds.com.au Assembly Instruction Manual Australian Made PLEASE LEAVE A REVIEW www.abscosheds.com.au/review Model: 1208WSK-PTX 14/12/23 2.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made GENERAL INSTRUCTIONS SAFETY NOTES • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made COMPONENT PACKING LIST QTY DESCRIPTION Check off all components. PART # CHK QTY DESCRIPTION PART # 2 STEEL SHEET 44.5” x 30.4” 44A 1 STEEL SHEET 34” x 30.4” 44B 2 STEEL SHEET 44.5” x 30.4” 44J 1 STEEL SHEET 34” x 30.4” 44T 1 STEEL SHEET 41” x 30.4” 44K 2 CHANNEL 47.9” 68D 2 CHANNEL 41” 68H 2 CHANNEL 44.5” 68B 1 CHANNEL 41” 68J 1 CHANNEL 42.2” 68K 2 CHANNEL 34” 68E 1 CHANNEL 42.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made SNAPTiTE ASSEMBLY GUIDE The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners. To assemble each panel, the perimeter channels are secured to the top and bottom of each panel. Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet. Each perimeter channel must finish flush with the edges of the sheets.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made REAR PANEL ASSEMBLY 1x required. 1. Place the 44J sheet with the edge holes as shown. 44A Orientate the 44B sheet so holes are as shown Overlap the sheets by four ribs. TIP: Correct overlap makes coverage the same as 68K channel length. 44J Ed ge ho les thi ss ide 2. Make sure the ends of the sheets are flush at overlap before continuing.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made ROOF PANEL ASSEMBLY 1. Place the 44T sheet with the two pan holes as shown. 1x required. 44T Orientate the 44B sheet so holes are as shown Overlap the sheets by three ribs. Tip Correct overlap makes coverage the same as 68D channel length. 44B 2. Make sure the ends of the sheets are flush at overlap before continuing. rst re sa fi sh flu 3. Attach the two 68D channels to both ends of the sheets using the SNAP-TiTE method.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made LEFT PANEL ASSEMBLY 1x required. his SN AP TT i E ide s o eh g Ed t les 58C 2. Attach the top and bottom channels using the SNAP-TiTE method. Make sure you have the shorter, 0.6” side of the channel to the exterior of the sheeting 44J 58C 1. Orientate the 44J sheet as shown. SN AP TT i E 0.6 0.8 68B 3. Attach the edge channel 68B to the side without edge holes. 0.8 0.6 Insert the longer 0.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H Australian Made RIGHT PANEL ASSEMBLY 1x required. 1. Orientate the 44A sheet as shown. 2. Attach the top and bottom channels using the SNAP-TiTE method. P TE NA T i 58C S Make sure you have the shorter, 0.6” side of the channel to the exterior of the sheeting 44A 58C 0.6 P TE NA T i S 0.8 68B 3. Attach the edge channel 68B to the side without edge holes. Insert the longer 0.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H SHELF PANEL ASSEMBLY 1x required. Australian Made 68C SN AP TT i E 1. Attach the end channels to the 44K sheet using the SNAPTiTE method. Make sure you have the shorter, 0.6” side of the channel to the outside of the sheeting 68C 44K SN 0.6 AP TT i E 0.8 68J 68H 2. Attach the front and rear channels. Insert the longer 0.8” side of the channel in the top and bottom channels, on top of the sheet and let the bottom side go under. 0.8 0.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H 2 PANEL CONSTRUCTION Make sure to have the wall panels orientated correctly with all holes intended for the shelf to the top. ar Re 3 Sid e 1 Australian Made 1. Start with the rear and left panel. Sit the side wall on the rear wall channels as shown. Overlap sheets so the sheet with four holes is to the front. Predrill with the 1/8” bit and fasten with three screws FAST096 l ne pa e up f l e sid Sh lour Co Inside of right 2.
ABSCO WOOD STORE MODEL: 1208WSK-PTX 4’ W x 2’10” D x 3’9” H ANCHORING Australian Made It’s best practice to anchor this structure to a concrete slab as shown. Each anchor consists on one nut, bolt, dynabolt and steel angle. 1. Drill a 10 mm hole into the side wall sheet. 2. Drill a 10 mm hole into the concrete slab. 3. Position the steel angle. 4. Place the dynabolt into the concrete hole & tighten. 5. Secure the steel angle to the wall sheet using the nut & bolt. 6.
