ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made ASSEMBLY APP AVAILABLE ON We highly recommend downloading the Absco Sheds Assembly App to assist with your build. + Scan to download STEP BY STEP ASSEMBLY VIDEOS • PARTS CHECKLISTS • FAQ • 7 DAY CUSTOMER SERVICE • WARRANTY INFORMATION • COUNCIL FORMS 4” 10’ RETE CONC SLAB 10’ 2” 2” WALLS SIT ON THIS LEVEL When laying a concrete slab for your shed, it is best practise to have a rebated edge to prevent water ingress.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made GENERAL INSTRUCTIONS SAFETY NOTES • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages. • Do not erect your shed in windy conditions. Some parts may have sharp edges.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY 2 2 COMPONENT DESCRIPTION STEEL SHEET 5' 10 9⁄32" Long 2' 6 7⁄16" Wide 30A STEEL SHEET 5' 10 9⁄32" Long 2' 6 7⁄16" Wide 31A STEEL SHEET 2 5' 10 9⁄32" Long 2' 3 63⁄64" Wide 1 34A 2 1 2 STEEL SHEET 6' 3 25⁄64" 2' 6 7⁄16" Wide 36R 4 2 STEEL SHEET 6' 8 33⁄64" Long 2' 6 7⁄16" Wide 38R 2 2 STEEL SHEET 6' 8 33⁄64" Long 2' 6 7⁄16" Wide 38L 2 8 STEEL SHEET 5' 5
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 2 COMPONENT DESCRIPTION PART No. 84R CHANNEL L = 14' 11 49⁄64" CHECK QTY 4 1 COMPONENT DESCRIPTION PART No.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 10 COMPONENT DESCRIPTION CHANNEL JOINER L= 7 7/8" PART No.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G Australian Made 10’ W x 10’ D x 7’ H INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> = JOIN>> JOIN>> <
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30302G Australian Made 10’ W x 10’ D x 7’ H STEP 1.
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier 10’ Garden Shed - Model: J30302G Australian Made W x 10’ D x 7’ H STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = 1 TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW RIDGE BEAM 4' 11 7⁄8" PARTS 97AL & 97AR QTY. = 2 QTY.
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier10’Garden Australian Made W x 10’ D Shed x 7’ H - Model: J30232G INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2" OVERLAP OF THE RIDGE CAP 2" INSTRUCTIONAL VIDEOS STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 8 55/64" IN EACH RIDGE CAP. 4" 8 55⁄6 2" STAGE 3: TURN RIDGE CAP OVER AND MEASURE 9 27⁄32" FROM THE END OF EACH RIDGE CAP.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTX ABSCO INDUSTRIES 87A 14A 97A 45A 81A 45A 45A 45A 45A 14A 81A 87A INSTRUCTIONAL VIDEOS 60A PAGE 10 10’ W x 10’ D x 7’ H 27/07/22 ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14 87A 45A 45A 45A 87A VIEW OF ROOF COMPONENTS Premier Garden Shed - Model: J30302G ABSCO PREMIER SHED MODEL: 30302GK-PTX Australian Made PAGE 10
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTX 27/07/22 PAGE 11 NDUSTRIES VIEW OF WALL COMPONENTS ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14 INSTRUCTIONAL VIDEOS PAGE 11 Australian Made
ABSCO PREMIER SHED Premier Garden Shed INSTRUCTIONS MODEL: 30302GK-PTXAND VIDEOS Model: Australian Made 10’ W x 10’ 30152GK D x 7’ H ABSCO ASSEMBLY INTRODUCTION The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H ed REAR PANEL ASSEMBLY ge ho les to ou Australian Made 1. Overlap specified sheets as shown. Make sure ends are flush. tsi de Where possible, have sheets orientated so printed part numbers are as shown. 30A 31A 31A Part numbers are found on the inside of the sheeting near the corner. ed 30A ge ho les to ou Shown as grey box on left tsi de START HERE 2.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made ROOF PANEL ASSEMBLY 2 completed panels are required. START HERE 45A Orientate all sheets so the short ends with the holes are on the same side and lined up. 45A 45A 45A Fit 81A channel to edge of sheet with these holes. 87A 60A SN E APT iT SN This is the edge 81A that will be screwed down on top of the wall in the final stage.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made SIDE PANEL ASSEMBLY 2 completed panels are required. START HERE 36R Overlap specified sheets as shown. Make bottom edges flush. 38R 38L 36L INS IDE OF SH ED Trim the tip of each sheet to allow channels to fit hard up to the edge of the sheet.
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G 10’ W x 10’ D x 7’ H FRONT PANEL ASSEMBLY Australian Made 89A START HERE LAY SHEETS OUT AS SHOWN 34A 89A START HERE 34A NOTCH ON JAMB 90A FITS OVER JAMB 89A AND 89B AND NOTCH ON 89B AND 89A FITS OVER 55A A 55 89 A A 90 DO NOT INSTALL THIS SCREW (OR THE TOP EQUIVALENT) UNTIL CHANNELS 55A AND 55C ARE INSTALLED 55A 90A 79A 55C A 55 A 89 A 79 C 55 NOTCH ON JAMB 89A AND 89B FITS OVER CHANNEL 55C AND CHANNEL 79A IN
ABSCO PREMIER SHED PremierMODEL: Garden30302GK-PTX Shed - Model: J30232G 10’ W x 10’ D x 7’ H Australian Made DOOR PANEL ASSEMBLY 58C START HERE ATTACH 58C CHANNELS AS DESCRIBED ON PAGE 12 58C 58A 58B B 12A A 58C 89C ATTACH 89C WITH COLORED SIDE FACING OUT.
ABSCO PREMIER SHED MODEL: 30302GK-PTX Premier Garden Shed 10’ W x 10’ D x 7’ H Model: 30152GK INSTRUCTIONS AND VIDEOS Australian Made DOOR PANEL ASSEMBLY 91A 91A Flip the door panel over and attach the 91A braces to the inside, screw up from beneath.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made PANEL CONSTRUCTION NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. Suggested assembly order - Front - Sides - Rear Side wall channels fit into the notched rear wall channels. Next, prepare a single roof panel as shown. Slide ridge beam down onto roof panel.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30302GK-PTX 10’ WModel: x 10’ D x 7’J30302G H ROOF CONSTRUCTION SLIDE THE ROOF PANEL INTO POSITION, AND SECURE WITH ONE SCREW AT EACH CORNER ONLY AT THIS STAGE Australian Made INSIDE VIEW OF FIXING SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END MOVE THE OTHER ROOF PANEL INTO POSITION AND SECURE PEAK BRACE TO RIDGE BEAM AND ROOF PANEL WITH ONE SCREW AT EACH END INSTRUCTIONAL VIDEOS ABSCO INDUSTRIES ABSCO INDUSTRIES ASSEMBLY INS
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30302GK-PTX 10’ WModel: x 10’ D x 7’J30302G H Australian Made FINAL CONSTRUCTION 14A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP CHANNEL AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF 12 CONCRETE ANCHORS WALL SHEET BOLT & NUT ANCHOR •- EACH EACH ANCHORCONSISTS CONSISTSOF OFONE ONENUT, NUTBOLT, & BOLT, A DYNABOLT AND STEEL ANGLE DYNABOLT AND STEEL ANGLE.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made REINFORCING ROOF INSTALL ADDITIONAL SCREWS ALONG THE UNDERSIDE OF THE RIDGE BEAM, CENTERED IN EVERY SECOND PAN OF THE ROOF SHEETING AS PICTURED. THESE POSITIONS DO NOT HAVE PRE-PUNCHED HOLES SO USE THE SUPPLIED DRILL BIT TO PREDRILL HOLES THROUGH THE RIDGE BEAM, THE ROOF PANEL CHANNEL INSIDE IT AND THE ROOF SHEET. FIX USING A FAST001 SELF TAPPING SCREW IN EACH OF THESE POSITIONS.
ABSCO PREMIER SHED MODEL: 30302GK-PTX 10’ W x 10’ D x 7’ H Australian Made EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.
