ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made ASSEMBLY APP AVAILABLE ON We highly recommend downloading the Absco Sheds Assembly App to assist with your build. + Scan to download STEP BY STEP ASSEMBLY VIDEOS • PARTS CHECKLISTS • FAQ • 7 DAY CUSTOMER SERVICE • WARRANTY INFORMATION • COUNCIL FORMS 4” RETE CONC 5’ 4 SLAB 10’ 2” ” WALLS SIT ON THIS LEVEL When laying a concrete slab for your shed, it is best practise to have a rebated edge to prevent water ingress.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made GENERAL INSTRUCTIONS SAFETY NOTES • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages. • Do not erect your shed in windy conditions. Some parts may have sharp edges.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX Model: 30152GK 10’ W x 5’ D x 6.5’ H INSTRUCTIONS AND VIDEOS Australian Made COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART CHECK QTY No.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX Model: 10’ W x 5’ D30152GK x 6.5’ H INSTRUCTIONS AND VIDEOS Australian Made COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY 8 COMPONENT DESCRIPTION PART CHECK QTY No.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX Model: 10’ W x 5’ D30152GK x 6.5’ H INSTRUCTIONS AND VIDEOS Australian Made COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY 2 COMPONENT DESCRIPTION PART No. 89A Part No. Here CHECK QTY 4 JAMB L= 5' 10 1/4" 1 CHECK 91A Part No. Here 4 85A A 85 LIP TRIM L= 2' 7 5/16" JAMB L= 5' 7 15/16" 1 PART No. JAMB L= 3' 8 1/8" 89C Part No. Here COMPONENT DESCRIPTION 90A Part No.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX INSTRUCTIONS AND VIDEOS Model: 10’ W x 5’ D30152GK x 6.5’ H Australian Made INSTRUCTIONS FOR JOINING SPLICED CHANNELS NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = CSJ JOIN>> = JOIN>> JOIN>> <
ABSCO PREMIER SHED MODEL: 30152GK-PTX Premier Garden Shed 10’ W x 5’ D x 6.5’ H Model: 30152GK INSTRUCTIONS Australian AND VIDEOS Made STEP 1.
ABSCO PREMIER SHED MODEL: 30152GK-PTX Premier Garden Shed INSTRUCTIONS AND VIDEOS Australian 10’ W x 5’ D x 6.5’ H Model: 30152GK Made STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = 1 TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW RIDGE BEAM 4' 11 7/8" PARTS 97AL & 97AR PUSH QTY. = 1 PUSH QTY.
ABSCO PREMIER SHED PremierMODEL: Garden 30152GK-PTX Shed - Model: J30232G 10’ W x 5’ D x 6.5’ H Australian Made INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2" OVERLAP OF THE RIDGE CAP 2" INSTRUCTIONAL VIDEOS STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 8 55/64" IN EACH RIDGE CAP. 4" 8 55⁄6 2" STAGE 3: TURN RIDGE CAP OVER AND MEASURE 9 27⁄32" FROM THE END OF EACH RIDGE CAP.
ABSCO INDUSTRIES NO. 14A 97A ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTX 27/07/22 PAGE 52A 52A 52A ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16 85A 52A 52A 81A 52A 14A 60A 85A 10’ W x 5’ D x 6.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTX 81E 36L 27/07/22 ABSCO INDUSTRIES 82R 34A 55C 90A 89A 79A 91A 91A 89A 81E 36R ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16 36R 31A 31A 30A 82R 36L A 34A 15A 82L B 55A PAGE 11 22A INSTRUCTIONS AND VIDEOS 10’ W x 5’ D x 6.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX 10’ W x 5’ D30152GK x 6.5’ H Model: INSTRUCTIONS AND VIDEOS Australian Made ABSCO ASSEMBLY INTRODUCTION The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H ed REAR PANEL ASSEMBLY ge ho les to ou Australian Made 1. Overlap specified sheets as shown. Make sure ends are flush. tsi de Where possible, have sheets orientated so printed part numbers are as shown. 30A 31A 31A Part numbers are found on the inside of the sheeting near the corner. ed 30A ge ho les to ou Shown as grey box on left tsi de START HERE 2.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made ROOF PANEL ASSEMBLY 2 completed panels are required. START HERE 52A Orientate all sheets so the short ends with the holes are on the same side and are lined up. 52A 52A 52A Fit 81A channel to edge of sheet with these holes. 85A 60A E APT iT SN 81A This is the edge SN that will be screwed down on top of the wall in the final stage.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made SIDE PANEL ASSEMBLY 2 completed panels are required. ST AR T Overlap both sheets as shown. Make bottom edges flush. HE RE 36R 36L Trim the tip of each sheet to allow channels to fit hard up to the edge of the sheet.
ABSCO PREMIER SHED Premier Garden Shed MODEL: 30152GK-PTX 10’ W x 5’ D30152GK x 6.5’ H Model: INSTRUCTIONS AND VIDEOS FRONT PANEL ASSEMBLY 4.
ABSCO PREMIER SHED Premier Garden Shed MODEL:30152GK 30152GK-PTX Model: INSTRUCTIONS AND VIDEOS 10’ W x 5’ D x 6.5’ H Australian Made 5.
ABSCO PREMIER SHED MODEL: 30152GK-PTX Premier Garden Shed Model: 30152GK 10’ W x 5’ D x 6.5’ H INSTRUCTIONS AND VIDEOS Australian Made DOOR PANEL ASSEMBLY 91A 91A Flip the door panel over and attach the 91A braces to the inside, screw up from beneath.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made PANEL CONSTRUCTION NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. Suggested assembly order - Front - Sides - Rear Side wall channels fit into the notched rear wall channels. Next, prepare a single roof panel as shown. Slide ridge beam down onto roof panel.
ABSCO PREMIER SHED MODEL: 30152GK-PTX Premier Garden Shed 10’ W x 5’ D x 6.5’ H Model: 30152GK INSTRUCTIONS AND VIDEOS Australian 8.
ABSCO PREMIER SHED MODEL: 30152GK-PTX Premier Garden Shed 10’ W x 5’ D x 6.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made REINFORCING ROOF INSTALL ADDITIONAL SCREWS ALONG THE UNDERSIDE OF THE RIDGE BEAM, CENTERED IN EVERY SECOND PAN OF THE ROOF SHEETING AS PICTURED. THESE POSITIONS DO NOT HAVE PRE-PUNCHED HOLES SO USE THE SUPPLIED DRILL BIT TO PREDRILL HOLES THROUGH THE RIDGE BEAM, THE ROOF PANEL CHANNEL INSIDE IT AND THE ROOF SHEET. FIX USING A FAST001 SELF TAPPING SCREW IN EACH OF THESE POSITIONS.
ABSCO PREMIER SHED MODEL: 30152GK-PTX 10’ W x 5’ D x 6.5’ H Australian Made EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.
