PCMCIA Fast Ethernet Attached Port PC Card Quick Installation Guide M73-APO01-130
FCC REGULATORY STATEMENTS Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
INTRODUCTION This PCMCIA Fast Ethernet PC Card is designed for any Notebook PC with a PCMCIA or CardBus PC Card slot. With this PC Card, users can hook up to their Ethernet LANs at the speed of 100Mbps as 10 times faster than traditional LAN environment. Moreover, the support of full duplex mode makes the data rate double possible. The fantastic feature of 10/100M autonegotiation eliminates the compatible troubles. The PCMCIA Fast Ethernet PC Card is Microsoft Plug and Play compatible.
Windows 98 Windows ME Windows 2000 Windows XP Lantastic 6.
HARDWARE INSTALLATION 1. Locate the PCMCIA slot of your system. 2. Align the PCMCIA Fast Ethernet Attached Port PC Card toward the PCMCIA slot. Push evenly and steadily until it is seated. Notebook 3. Connect the attached RJ-45 port with an Ethernet Hub/Switch. 4. You are now ready to continue the software installation.
SOFTWARE INSTALLATION Installation for Windows 95 The installation procedures for the network driver may vary slightly depending on the version of Windows 95 you are using and also your current system configuration. 1. Once the PCMCIA Fast Ethernet PC Card is connected to your computer, Windows 95 will automatically detect the new hardware device as shown below. Insert the program diskette #1 into your floppy drive. 2. Click Next. When the PCMCIA Fast Ethernet PC Card message appears, click Finish.
new hardware device as shown below. Click Next. 2. Insert the device driver diskette into your floppy drive. When Windows prompts you What do you want Windows to do? Select Search for the best driver for your device. (Recommended). Click Next. 3. Follow the on-screen instruction to proceed.
4. The installation program will proceed automatically. 5. If you are asked to insert Windows 98 CDROM in the selective drive, please do so to have Windows copy all the necessary files to your system. . When the following window appears, click Finish. 1. Click Yes to restart your computer.
Installation for Window ME 1. Once the PC Card is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the Location of the driver… and click Next. 2. Insert the device driver disk into the floppy disk drive on your system. Select Removable Media (Floppy, CD-ROM… ) and click Next. 3.
(Recommended). Click Next. 4. Click Next to continue. 5. Windows will copy the appropriate driver to your system. If Windows ME asks you to supply your original Windows ME installation CD-ROM, load it on the CDROM drive. 6. Click Finish to complete the software installation.
Installation for Windows NT 4.0 This section describes the installation for Windows NT under the condition that Windows NT is already installed in your computer. If your computer is not yet networking installed, refer to the Windows documentation for details. Also remember to have your original Windows NT CD-ROM handy before you begin the installation. For Windows NT may ask for it during the installation. 1.
5. When asked to supply the path to the disk, type a:\ and click OK. 6. Windows NT will ask you to supply the I/O Base, Interrupt, and Memory values for the card. Good values to start with are 300 (for the I/O Base) and 5 (for the IRQ). 7. When you're finished, click OK. Windows NT will copy necessary files to your computer. 8. When the Network window reappears, click on the Bindings tab. Choose your bindings. Click on the Protocols tab and select your settings. Do the same for the Services tab. 9.
2. When Windows prompt you a FOUND NEW HARDWARE WIZARD dialog box, select Search for the … and press Next. 3. Windows will prompt an FOUND NEW HARDWARE WIZARD dialog box. In this time, select Floppy disk drives and insert the driver diskette. Press Next. When asked for the original Windows 2000 CD/disks please follow the on-screen instruction.
4. Wait for a while until Windows has found the appropriate driver. 5. Click Yes to continue.
6. Click Finish. The PC Card driver installation is successfully completed. 7. For the first time installation, click Network icon in Control Panel to add Protocols, Client and Service if needed. 8. Reboot your computer to activate the new device. Installation for Windows XP 1.
Windows will detect the new device and prompt you to insert the network device driver. Insert the device Driver Disk into the floppy disk drive of your system. Click Install the software automatically (Recommended) and click Next. 2. Windows will start searching for the appropriate driver for this hardware. Select any drivers named as PCMCIA Fast Ethernet Card, and click Next.
3. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click Continue Anyway to proceed. 4. Wait while Windows copies appropriate driver to your system. 5. Click Finish. The software installation for this network device is now completed.
APPENDIX A. SPECIFICATIONS Network Interface Specifications IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseTX Data Rate 10/100 Mbps, Double data rate in Full Duplex mode Operating Systems For Notebook PC: ( with accessory adapter) Novell Netware 3.x, 4.x Microsoft LAN Manager Packet Driver Applications Microsoft Windows for Workgroups 3.11 Windows 3.1 Microsoft Windows NT 3.51, NT 4.
General Specification LEDs: Six LEDs on the Attached Port Link (Green, On) 100/10 (Orange, On/Off) Full (Green, On) RX (Green, Blink) COL (Orange, On) TX (Green, Blink) Environments Ranges Operating: 32°F to 149°F (0°C to Storage: -4°F to 158°F (0°C to 65°C) 70°C) Humidity: noncondensing 10% - 90% , Certifications FCC, Part 15, Class B, VCCI-B CE Mark (EN50081-1/50082-1, Class B) - 17 -
