Internal Fax Modem 56K Quick Installation Guide M73-APO02-460
FCC Part 68 Registration This device complies with FCC Part 68 rules, and the use of this device is subject to the following restrictions: 1. The FCC has established rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones. 2.
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
HARDWARE INSTALLATION Precautions: Please be sure you take adequate anti-static precautions when handling this product. The simplest way to achieve this is; touch a non-painted surface of the computer’s chassis during the hardware installation. 1. 2. 3. 4. 5. 6. Make sure the computer is turned off before installing the device. Remove the expansion slot cover from the computer. Carefully slide the PCI modem card into an available PCI slot, applying even pressure to the card.
SOFTWARE INSTALLATION Windows 98 Installation 1. Reboot the computer system after the modem is well inserted into the PCI slot of your computer. Windows 98 will automatically detect the device. Click Next to continue. 2. Insert the device driver compact disc into your CD-ROM drive when the following dialog box appears. Click Next to continue.
3. Select Specify a location and press Browse to choose the Dirver\Win98 folder in your CD-ROM drive. Then click Next. 4. Click Next to continue. 5. When the following figure appears, click Finish to complete software installation.
Windows 2000 Installation 1. Reboot the computer system after the modem is well inserted into the PCI slot of your computer. Windows 2000 will automatically detect the new hardware device and prompt the following message. Click Next to continue 2. Select Search for a suitable driver for my device (recommended) and click Next. Select Specify a location and click Next. Insert the device driver compact disc into your CD-ROM drive.
5. Click Next. Windows 2000 will start copying necessary files onto your system. 6. Click Yes to continue. 7. Click Finish to complete the software installation. Windows ME Installation 1. Reboot the computer system after the modem is well inserted into the PCI slot of your computer.
2. 3. and prompt the following message. Select Specify the location of the driver (Advanced) and click Next. Insert the device driver compact disc you’re your CD-ROM drive. Select Specify a location and click browse to the location where the driver is stored (Driver\Winme). And then click Next. Click Next to continue.
4. 5. Click Finish when the following screen prompts. The installation program will continue. Repeat the step 1 as described above. 6. Follow the continue. on-screen 7. Click Next to continue.
8. Press Finish to complete the software installation. 9. Go to Start Settings Control Panel Systems Device Manager. Click Modem and WDM Modem Enumerator to expand. If Agere System Soft Modem is listed as below, the software installation will truly be completed. If not, please consult your distributor for the technical support.
Windows XP Installation 1. 2. Reboot the computer system after the modem is well inserted into the PCI slot of your computer. Windows XP will automatically detect the new hardware device and prompt the following message. Select Install from a list or specific location and click Next. Insert the device driver compact disc into your CD-ROM drive. Select Include this location in the search and click Browse to direct Windows XP to the location where the driver stored (\Driver\xp). Then click Next.
3. When the following window appears, click Continue Anyway. 4. Please wait a while for windows to copy a number of files onto your PC. Click finish to complete the software installation. 5.
Windows NT Installation 1. 2. 3. 4. 5. 6. Reboot the computer system after the modem is well inserted into your PCI slot of your computer. Load the device driver compact disk in your CD-ROM drive. Start Windows NT. Go to My Computer. Click the CD-ROM drive. Click the driver\Winnt4 folder. Or you may click the Browse button to select the CD-ROM drive and the driver\Winnt4 folder. Double-click Setup.exe. The installation program will proceed automatically.
CHECKING COUNTRY/REGION Perform the following steps to check the country/region settings for the modem before using the Internal Fax Modem 56K. For the best performance, make sure the country/region is selected to the country where you are using the device, e.g., United States of America. Windows 98/ 98SE/ 2000/ Millennium 1. 2. Go to Start→Settings→Control Panel→Modems. Specify the country/region where you are when the Location Information dialog box appears. And then click Close. Windows XP 1. 2. 3.
UNINSTALL If you want to uninstall the driver of the Internal Fax Modem 56K after installation, perform the following steps. 1. Go to My Computer. 2. Select the CD-ROM drive which contains the Internal FaxModem 56K device driver. 3. Choose and double-click the Win98, WinME or Winnt4, Win2000, XP folder depending on the system you are working on. 4. Click Agrsmdel.exe. The Internal Fax Modem 56K device driver will automatically removed. Windows NT4.0 1.
2. 3. Start→Settings→Control Panel→Modems. When the Modems Properties dialog box appears, click the Dialing Properties button. When the Dialing Properties dialog box appears, specify the country/region that you are in and click OK. UNINSTALL If you want to uninstall the driver of the Internal Fax Modem 56K after installation, perform the following steps. 1. Go to My Computer. 2. Select the CD-ROM drive which contains the Internal FaxModem 56K device driver. 3.
device. Name the new appropriately and click Next. 4. 5. connection Enter the area code and phone number provided by your Internet Service Provider (ISP). Follow the on-screen instruction to proceed. When finished, from the Dial-Up Networking window, right-click your newly built connection. Select Properties. On the Server Types tab, enter the proper selections as shown below and click OK to finish the settings.
. You are now ready to connect to the Internet.
