Multi-Homing Dual WAN Firewall Router Quick Installation Guide M73-APO09-400
Multi-Homing Dual WAN Firewall Router Overview The Multi-Homing Dual WAN Firewall Router provides three 10/100Mbit Ethernet network interface ports which are the LAN, WAN 1, and WAN 2 port. It also provides an easily operated software WebUI that allows users to set system parameters or monitor network activities using a web browser.
Multi-Homing Dual WAN Firewall Router supporting protocols The Multi-Homing Dual WAN Firewall Router supports all the TCP, UDP and ICMP protocols, such as HTTP, TELNET, SMTP, POP3, FTP, DNS, PING, etc. System Administrators can set up proprietary protocols according to operating requirements. Hardware Description Reset DC Power WAN 2 External 2 Port WAN 1 External 1 Port LAN External Port (WAN 1): Use this port to connect to the WAN 1 router, DSL modem, or Cable modem.
Connecting Example: Multi-Homing: LAN Port = 192.168.1.1 WAN 1 Port = x.x.x.x (provided by ISP) WAN 2 Port = x.x.x.x (provided by ISP) Connection Type: 10/100 Mbps Cable Connection 【LAN 1 Port】= 192.168.1.3 【LAN 2 Port】= 192.168.1.4 【LAN 3 Port】= 192.168.1.5 【LAN 4 Port】= 192.168.1.6 【WAN 1 Port】= 61.11.11.11 【WAN 2 Port】= 61.22.22.
Multi-Homing Dual WAN Firewall Router Software (management tool) description Multi-Homing Dual WAN Firewall Router management tool: WebUI The main menu functions are located on the left-hand side of the screen, and the display window will be on the right-hand side. The main functions include 12 items, which are: Administrator, Configuration, Address, Service, Schedule, Policy, VPN, Virtual Server, Log, Alarm, Statistics, and Status.
Quick Setup WebUI Configuration example STEP 1: Connect both the Administrator’s PC and the LAN port of the Multi-Homing Dual WAN Firewall Router to a hub or switch. Make sure there is a link light on the hub/switch for both connections. The Multi-Homing Dual WAN Firewall Router has an embedded web server used for management and configuration. Use a web browser to display the configurations of the Multi-Homing (such as Internet Explorer 4(or above) or Netscape 4.0(or above) with full java script support).
STEP 2: Once the Administrator PC has an IP address on the same network as the Multi-Homing Dual WAN Firewall Router, open up an Internet web browser and type in http://92.168.1.1 in the address bar. A pop-up screen will appear and prompt for a username and password. A username and password is required in order connect to the Multi-Homing. Enter the default login username and password of Administrator (see below).
STEP 3: After entering the username and password, the Multi-Homing Dual WAN Firewall Router WEBUI screen will display. Select the Interface tab on the left menu and a sub-function list will be displayed. Click on LAN from the sub-function list, and enter proper Layer 3 network setup information. (for example) LAN interface IP Address 192.168.1.1 NetMask 255.255.255.0 Select the Interface tab on the left menu and a sub-function list will be displayed.
Click Modify to modify WAN 1/2 settings. Note: The above figures are only examples. Please fill in the appropriate IP address information provided to you by the ISP.
STEP 4: Click on the Policy tab from the main function menu, and then click on Outgoing from the sub-function list. Click on New Entry button. When the New Entry option appears, then enter the following configuration: Source Address – select “Inside_Any” Destination Address – select “Outside_Any” Service - select “ANY” Action - select “Permit” Click on OK to apply the changes.
STEP 5: The configuration is successful if you see the screen below. Make sure that all the computers that are connected to the LAN port have their Default Gateway IP Address set to the Multi-Homing’s LAN IP Address (i.e. 192.168.1.1). At this point, all the computers on the LAN network should gain access to Internet immediately. If a Multi-Homing filter function is required, please refer to the Policy section.
