0/100Mbps Dual Speeds Fast Ethernet PC Card Quick Installation Guide
HARDWARE INSTALLATION 1. Locate the PCMCIA slot of your system. 2. Align the PCMCIA Fast Ethernet Attached Port PC Card toward the PCMCIA slot. Push evenly and steadily until it is seated. 3. Connect the attached RJ-45 port with an Ethernet Hub/Switch. 4. You are now ready to continue the software installation.
LED Indicators 100M/FULL: grows orange at 100 Mbps, green at FULL duplex. • LINK/RX: grows green when connected to the network, blinks green when receiving datum. • POWER/TX: grows green when power is on, blinks green when transmitting datum.
SOFTWARE INSTALLATION Windows NT 3.51 1. In Main Group of NT 3.51, open Control Panel and click on Network icon. 2. In Network Settings dialog box, push Add Adapter... button. The Add Network Adapter dialog box will appear. 3. Choose requires disk from manufacturer from the network adapter card list and press Continue.. 4. When Windows NT prompts for manufacturer disk, insert driver diskette and press OK until the Network Setting Change dialog box appears. 5.
11. A dialog box will appear to adjust the driver's settings. The resources assignment to the adapter must be unique in the system. 12. Press OK when all setting are completed. 13. Press Close to complete network setting Windows 95 Installation 1.Assumed that the drivers of PC Card slot are well installed. The System Icon in the Control Panel can report on its functionality. Apart from above mentioned, any questions on this layer need to be taken up with the computer's manufacturer. 2.
5.Reboot the machine and the card will be fully functional. Windows 98 Installation 1.Assumed that the drivers of PC Card slot are well installed. The System Icon in the Control Panel can report on its functionality. Apart from above mentioned, any questions on this layer need to be taken up with the computer's manufacturer. 2.Insert the PC Card into the slot. In New Hardware Found dialog box, select Driver from disk provided by hardware manufacturer. 3.
5.Windows will prompt a ADD NEW HARDWARE WIZARD dialog box. In this time, select Floppy disk drives and please insert driver diskette. Then press Next, the driver will be installed and you may be asked for the original Windows 98 CD/disks. 6.For the first time installation, please click Network icon in Control Panel to add Protocols, Client and Service if you needed. 7.Reboot the machine and the card will be fully functional.
Windows 2000 Installation 1. Assumed that the drivers of PC Card slot are well installed. The System Icon in the Control Panel can report on its functionality. Apart from above mentioned, any questions on this layer need to be taken up with the computer's manufacturer. 2. Insert the PC Card into the slot, and wait for the install wizard. 3. Windows will prompt a Found New Hardware Wizard dialog box, then press Next. 4. Then Windows will prompt a Install Hardware Device Drivers dialog box.
5. Windows will prompt a Locate Driver Files dialog box. In this time, select Floppy disk drives and please insert driver diskette. Then press Next, the driver will be installed and you may be asked for the original Windows 2000 CD/disk.
6. For the first time installation, please click Network icon in Control Panel to add Protocols, Client and Service if you needed. 7. Reboot the machine and the card will be fully functional. Installation for Windows Workgroup 3.11 NDIS3 Driver for Workgroup 1. Click on "Network Setup" icon in "Network" program group. 2. In "Network Settings" dialog box, click mouse on "Networks..." button to select the network operating system. 3.
installation and exit Windows. 9. Run INSTALL.EXE from driver diskette's root directory. 10. Select "Windows for Workgroup" in "Network Operating System" screen and enter "Driver Install" screen. 11. If current settings are acceptable, select "Start Installation" and go to step 13. Otherwise, select "Modify Parameters" to make settings changed. 12. Move cursor to focus on the setting you want to make change and press Enter to select a fit value.
3. In Networks dialog box, check the radio button before "Install Microsoft Windows Network" and "No Additional Network". Press OK to go back the Network Settings screen. 4. Click on "Drivers..." button to select network driver. 5. In "Network Drivers" dialog box, press "Add Adapter..." button to enter "Add Network Adapter" dialog box. Select "Unlisted or Updated Network Adapter" and press OK. 6. Windows will prompt an "Install Driver" dialog box.
Back to step 11. 13. Select "NDIS Server(LAN Manager,...)" as the network server you will attach to and press Enter key. 14. Installation program starts copying related files from diskette to the destination directory and modifies AUTOEXEC.BAT and NET.CFG under user's agreement. 15. Installation is complete. Please reboot the computer to have the driver take effect. ODI Driver for Workgroup 1. Click on "Network Setup" icon in "Network" program group to install network driver. 2.
7. Select the "Netware ODI Driver ...." string and press OK. 8. Follow Windows instructions to complete the installation and exit Windows. 9. Run INSTALL.EXE from driver diskette's root directory. 10. Select "Windows for Workgroup" in "Network Operating System" screen and enter "Driver Install" screen. 11. If current settings are acceptable, select "Start Installation" and go to step 13. Otherwise, select "Modify Parameters" to make settings changed. 12.
directory. 2. Select "Netware 3.x or 4.x workstation" in "Network Operating System" screen and enter "Driver Install" screen. 3. If current settings are acceptable, select "Start Installation" and go to step 5. Otherwise, select "Modify Parameters" to make settings changed. 4. Move cursor to focus on the setting you want to make change and press Enter to select a fit value. When the configuration is acceptable, press Enter on the OK field to exit the screen. Back to step 3. 5.
>LSL ; Link Support Layer Module provided by Novell >LE100ODI ; Hardware Specific Module >IPXODI ; IPX Protocol Stack Module provided by Novell >NETx ; DOS Shell Support Module provided by Novell >LOGIN Novell Client Installation 1. Run the NetWare Client Install v1.21- Get the 4 Client disks from the network administrator or - Run the \NWCLIENT\INSTALL.EXE in a previous installation 2.
backup by a NetWare server running software such as SBACKUP? (Y/N): No 7. Answer accordingly and provide a path if necessary. 8. Select a driver for your network board. 9. From the driver list, select "Other Drivers". 10. Go to the Insert the Driver Disk dialog box and specify the path where the ODI driver and INS files reside. For example: C:\NETWARE. 11. Press Enter and select the target ODI driver. 12. Specify the driver's optional settings. 13. Press F10 to save to new configuration. 14.
performs the following: SET NWLANGUAGE=ENGLISH --Set NetWare 4.X to English language LSL --Link Support Layer Module provided by Novell LE100ODI --Hardware Specific Module IPXODI --IPX Protocol Stack Module provided by Novell VLM --DOS Support Module provided by Novell F: --Change to connected device LOGIN .ADMIN --Login to file server as user ADMIN 16. Run STARTNET to access the Novell network. MS LAN Manager 1.View the README.TXT on the installation diskette in the \NDIS2 directory.
Installation and go to step 6. Otherwise, select Modify Parameters to make setting changed. 5.Move cursor to each field you want to make a change and press to select a fit value. When the configuration are set completely, press on the OK field to exit the screen and go back to step 4. 6.Installation program starts to copy related files from driver diskette to the destination directory and modifies CONFIG.SYS and PROTOCOL.INI under user’s agreement. 7.
Drivername = netbeui$ SESSIONS = 6 NCBS = 12 BINDINGS = "LE120NDS_NIF" LANABASE = 0 [LE120NDS_NIF] ; protocol.ini session for LAN driver. IOADDRESS = 0x320 INTERRUPT = 11 DRIVERNAME = LE100NDS$ Packet Driver 1.Run INSTALL.EXE from root directory of driver diskette. 2.Select Packet Driver item on the menu screen. 3.If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters to make setting changed. 4.
