Firewall VPN Router Quick Installation Guide M73-APO09-380
Firewall VPN Router Overview The Firewall VPN Router provides three 10/100Mbit Ethernet network interface ports which are the Internal/LAN, External/WAN, and DMZ port. It also provides an easily operated software WebUI that allows users to set system parameters or monitor network activities using a web browser. Firewall VPN Router security feature Some functions that are available in the firewall are: Packet Filter, Proxy Server, Hacker invasion alarm, Packet monitor log, Policy, etc.
Firewall VPN Router supporting protocols The Firewall VPN Router supports all the TCP, UDP and ICMP protocols, such as HTTP, TELNET, SMTP, POP3, FTP, DNS, PING, etc. System Administrators can set up proprietary protocols according to operating requirements. Hardware Description DC Power Reset External Port DMZ Port Internal Port DMZ Port: Use this port to connect to the company’s server(s), which needs direct connection to the Internet (FTP, SNMP, HTTP, DNS).
Connecting Example: Firewall: Internal Port = 192.168.1.1 External Port = x.x.x.x (provided by ISP) DMZ Port = 172.16.1.254 Connection Type: 10/100 Mbps Cable Connection 【Internal 1 Port】= 192.168.1.3 【Internal 2 Port】= 192.168.1.4 【Internal 3 Port】= 192.168.1.5 【Internal 4 Port】= 192.168.1.
【External Port】 = 61.11.11.11 【DMZ Port】 = 172.16.1.254 Firewall VPN Router Software (management tool) description Firewall VPN Router management tool: WebUI The main menu functions are located on the left-hand side of the screen, and the display window will be on the right-hand side. The main functions include 12 items, which are: Administrator, Configuration, Address, Service, Schedule, Policy, VPN, Virtual Server, Log, Alarm, Statistics, and Status.
Quick Setup WebUI Configuration example STEP 1: Connect both the Administrator’s PC and the Internal (LAN) port of the Firewall VPN Router Firewall to a hub or switch. Make sure there is a link light on the hub/switch for both connections. The Firewall VPN Router has an embedded web server used for management and configuration. Use a web browser to display the configurations of the firewall (such as Internet Explorer 4(or above) or Netscape 4.0(or above) with full java script support).
STEP 2： Once the Administrator PC has an IP address on the same network as the Firewall VPN Router, open up an Internet web browser and type in http://92.168.1.1 in the address bar. A pop-up screen will appear and prompt for a username and password. A username and password is required in order connect to the firewall. Enter the default login username and password of Administrator (see below).
STEP 3: After entering the username and password, the Firewall VPN Router WEBUI screen will display. Select the Configuration tab on the left menu and a sub-function list will be displayed. Click on Interface from the sub-function list, and enter proper Layer 3 network setup information. (for example) Internal interface External DMZ IP Address 192.168.1.1 NetMask 255.255.255.0 IP address 211.222.20.100 NetMask 255.255.255.0 Default Gateway 211.222.20.101 IP address 192.168.3.1 NetMask 255.
STEP 4： Click on the Policy tab from the main function menu, and then click on Outgoing from the sub-function list. Click on New Entry button. When the New Entry option appears, then enter the following configuration: Source Address – select “Inside_Any” Destination Address – select “Outside_Any” Service - select “ANY” Action - select “Permit” Click on OK to apply the changes.
STEP 5： The configuration is successful if you see the screen below. Make sure that all the computers that are connected to the Internal (LAN) port have their Default Gateway IP Address set to the Firewall’s Internal IP Address (i.e. 192.168.1.1). At this point, all the computers on the Internal network should gain access to Internet immediately. If a firewall filter function is required, please refer to the Policy section.
