WL-5470AP Wireless Access Point User’s Manual 1 WL5470AP User’s Manual
Declaration of Conformity We, Manufacturer/Importer OvisLink Corp. 5F., NO.6, Lane 130, Min-Chuan Rd., Hsin-Tien City, Taipei County, Taiwan Declare that the product Wireless AP WL-5470AP is in conformity with In accordance with 89/336 EEC-EMC Directive and 1999/5 EC-R & TTE Directive Clause Description ■ EN Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission equipment operating in the 2.
WL-5470AP CE Declaration Statement Country cs Česky [Czech] Declaration OvisLink Corp. tímto prohlašuje, že tento WL5470AP je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. da Undertegnede OvisLink Corp. erklærer herved, Dansk [Danish] at følgende udstyr WL-5470APoverholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. de Hiermit erklärt OvisLink Corp.
This device uses software which is partly or completely licensed under the terms of the GNU General Public License. The author of the software does not provide any warranty. This does not affect the warranty for the product itself. To get source codes please contact: OvisLink Corp., 5F, No. 96, Min-Chuan Rd, Hsin-Tien City, Taipei, Taiwan, R.O.C. A fee will be charged for production and shipment for each copy of the source code.
FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Statement Hereby, OvisLink Corp. declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Directive 1999/5/EC. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. All trademarks and brand names are the property of their respective proprietors. Specifications are subject to change without prior notification.
Table of Contents INTRODUCTION ................................................................................................................................................................ 1 FEATURES........................................................................................................................................................................ 2 PARTS, NAMES, AND FUNCTIONS................................................................................................................
Introduction ． WL-5470AP is world's most popular multi-function access point. It features an impressive total of 8 wireless multi-function modes that are not available in normal access point. In addition, the ACK timeout and RSSI feature makes it suitable for long distance application. From ordinary AP application to Hotspot and WISP usage, you will find the WL-5470AP is the device you want. ． WL-5470AP is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point.
Features 1. 4x100Mbps LAN ports for Wireless AP cascade.,2MB flash,16MB SDRAM. 2. TX output power is limited to 20dBm (EU), 23dBm (FCC), up to 25dBm (South America). 3. AP , Client, Bridge ,WDS, Universal mode. 4. WISP Client Router, WISP+ Universal, Gateway mode. 5. Allows WEP 64/128 bit. 6. Support WPA-PSK, WPA2-PSK encryption. 7. Support data rate automatic fallback. 8. Automatic channel selection. 9. Client access control. 10. Supports 802.
Parts, Names, and Functions 1. Front Panel: LED Indicators LED Power WAN Wireless Function Power indication WAN port activity Wireless activity Color Status Green On Green Blinking Green Description Power is being applied to this product. The WAN port is link. Solid The wireless function is ON. Blinking Sending or receiving data via wireless. An active station is connected to the LAN 1 LAN 2 LAN 3 Link activity Green corresponding LAN port.
2. Rear Panel: Connection Ports Port DC 12V Functions Connects the power adapter plug. LAN 1 LAN 2 LAN 3 Connects inside network group. LAN 4 WAN Connects inside network group or outside internet. Ant. Connects antenna.
Factory Default Settings Setting Wireless Access Point Device Name WL-5470AP SSID Default value: airlive Channel Default value: 11 in the USA/Canada market; Default value: 13 in the Europe market WEP Default value: Disabled IP Address Default value: 192.168.100. 252 DHCP Server z In AP, Client, and GW mode, the default DHCP Server is disabled, Please set your PC's IP to the same subnet as the AP to access the AP. In WISP, mode, the default DHCP server is enabled.
Hardware Connection Note: Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is placed the better will be the performance. 1. Connect to your local area network: connect an Ethernet cable to one of the Ethernet port. 2.
About the Wireless Operation Modes The WL-5470AP v2 device provides all 7 modes of wireless operational applications with: 1 2 3 4 5 6 7 8 Access Point Mode. Client Mode. Bridge Mode. WDS Mode. Universal Mode. WISP (Client Router) Mode. WISP + Universal Mode. GW Mode This device is shipped with configuration that is functional right out of the box.
Access Point Mode When acting as an access point (default setting), this device connects all the stations (PC/notebook with wireless network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. See the sample application below. To set the operation mode to “Access Point”, please go to “Mode JAP” and click the Setup button.
Client Mode (Infrastructure) If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface. Refer to the illustration below. This station (AP1 plus the connected computer 1) can associate to another Access Point (AP2), and then can have the Internet access if the other Access Point (AP2) has the Internet connection.
