Instruction Manual

27
11
14
13
8
4
2
30
15
8
23
24
25
17
42
21
22
16
20
10
7
9
6
New style
18
19
REF. NO. DESCRIPTION QTY/PUMP SE2PL SE2UL SE2RL SE3SL
6 Bracket 1 P-58-0703 30B P-58-0703 30B P-58-0703 30B P-58-0703 30B
7 ‘O’-ring, body 1 P-58-0719 72 P-58-0719 72 P-58-0719 72 P-58-0719 72
8 ‘O’-ring, screw 5 P-58-0717 72 P-58-0717 72 P-58-0717 72 P-58-0717 72
9 Screw, bracket 4 P-58-0715 10 P-58-0715 10 P-58-0715 10 P-58-0715 10
10 ‘O’-ring, segment 1 P-58-0754 72 P-58-0754 72 P-58-0754 72 P-58-0754 72
11, 13 Shaft seal & ‘O’-ring 1 P-58-0714 12 P-58-0714 12 P-58-0714 12 P-58-0714 12
& 14
15 Impeller 1 P-58-0704 30 P-58-0706 30 P-58-0975 30 P-58-0975 30
16 Screw, impeller 1 P-58-0716 10 P-58-0716 10 P-58-0716 10 P-58-0716 10
17 Volute 1 P-58-0702 30 P-58-0702 30 P-58-0977 30 P-58-0977 30
18 Screw, side volute 2 P-58-0725 10 P-58-0725 10 P-58-0725 10 P-58-0725 10
19 Screw, top volute 1 P-58-0997 10 P-58-0771 10 P-58-0771 10 P-58-0771 10
20 Check valve 1 P-58-0705 72 P-58-0705 72 P-58-0705 72 P-58-0705 72
21 Screw, body 10 P-58-1206 10 P-58-1206 10 P-58-1206 10 P-58-1206 10
22 ‘O’-ring, drain plug 1 P-58-1009 72 P-58-1009 72 P-58-1009 72 P-58-1009 72
23 Plug, drain 1 P-58-0723 30 P-58-0723 30 P-58-0723 30 P-58-0723 30
 24 Plug,ller  1 P-58-072230B P-58-072230B P-58-072230B P-58-072230B
 25 ‘O’-ring,llerplug  1 P-58-076572 P-58-076572 P-58-076572 P-58-076572
27 Key 1 P-58-0718 30 P-58-0718 30 P-58-0718 P-58-0718
30 Shim As required P-58-0778 11 (.006”) P-58-0778 11 (.006”) P-58-0778 11 (.006”) P-58-0778 11 (.006”)
“ P-58-0778 12 (.015”) P-58-0778 12 (.015”) P-58-0778 12 (.015”) P-58-0778 12 (.015”)
“ P-58-0778 13 (.030”) P-58-0778 13 (.030”) P-58-0778 13 (.030”) P-58-0778 13 (.030”)
42 Body 1 P-58-1002 30B P-58-1002 30B P-58-1002 30B P-58-0755 30B
CARING FOR PACER PUMPS
Whenhandlingagriculturefertilizerandchemicals,ushpump
with fresh, clean water and drain completely.
EPDM rubber components are not compatible with petroleum
products. Do not use petroleum products when preparing pump
for storage.
• Housing, volute and impeller: glass-reinforced polyester.
•Rubber parts: EPDM (Buna and Viton® available).
•Shaft seal: Stainless steel with carbon and ceramic
 faces,EPDMtted.
•Hardware: internal and external stainless steel fasteners.
• Working pressure: to 52 PSI.
• Flow: to 280 GPM.
NOTE:ThispartslistisintendedforEPDMttedpumpsonly.
Parts list for model numbers starting with SE2PL, SE2UL, SE2RL and SE3SL.