Owner Manual
Table Of Contents
- CAUTIONS
- FEATURES
- PRODUCT DISCRIPTION
- DIGITIAL DISPLAY
- OPERATRIONS
- POWER/FUNCTION BUTTON
- UTurn the dehumidifier on
- Plug in the unit, the display screen flashes for one second, it buzzes and the screen shows ”- -”. Now the unit is on standby.
- ● Press POWER button, the dehumidifier turns on and enters AUTO mode.
- Lights up when in AUTO mode and the fan runs at high speed.
- ●Press the POWER button to switch between the following modes.
- Flashes for 3 seconds and lights up when press the power button again. The unit enters CONTINUOUS drying mode and the fan runs at high speed.
- Flashes for 3 seconds and lights up when press the power button again. The unit enters SLEEP mode and the fan runs at low speed.
- Modes toggling is as follows:
- UTurn the dehumidifier off
- Long press the POWER button for 3 seconds, the screen shows”- -”, the compressor stops immediately and the fan stops 30 seconds later.
- Modes Explanation
- AUTO MODE
- If ambient humidity ≦ 47%. Then the compressor stops, the fan stops 30 seconds later.
- If ambient humidity ≥53% fan running at high speed for 3 seconds, compressor start working.
- CNT/DRY CLOTHES MODE
- In CNT mode, the dehumidifier continuously runs at high fan speed until the ambient humidity reaches 20%. It is suitable for clothes drying or conditions that require continuous dehumidification.
- SLEEP MODE
- If ambient humidity ≦ 47%. Then the compressor stops, the fan stops 30 seconds later.
- If ambient humidity ≥ 53% fan running at low speed for 3 seconds, compressor start working.
- Water Tank Full Alarm
- UWater Tank Indicator
- ● When the tank is full for 5 seconds, it sets the alarm. The water tank indicator turns red and the unit buzzes for 15 times.
- UClear the alarm
- ● When the buzz is on, press the POWER button to stop it. The compressor, fan and ionizer generator shut down and all the functions freeze until the tank is emptied and back in right position.
- UEmpty the tank
- ● Grab the notch at the bottom of the tank and pull it out with both hands.
- Take it slowly and steadily in case of spilled water.
- ● Empty the water.
- ● Put the water tank back in position. The dehumidifier automatically starts working again.
- MAINTENANCE
- Always make sure the water tank is locked into place when putting it back, otherwise the dehumidifier cannot start up.
- Do not remove the float out of the tank otherwise the dehumidifier cannot start up.
- If the tank is dirty, wash it with cool/warm water. Do not use cleanser, steel balls, chemically treated dust-proof cloth, gasoline, benzene, thinners or other chemical solvents in case of damage and leakage.
- TROUBLE SHOOTING
9
TROUBLE SHOOTING
1. FUNCTIONING TEMP.
41℉ ≤ Ambient Temp. ≤ 95℉
When the ambient temp is lower or higher than the functioning temp, the
dehumidifier stops operation.
When 41℉ ≤ Ambient temp. ≤ 60.8℉, the compressor automatically defrosts
at intervals; during defrosting, the compressor stops and the fan keeps
running.
2. BEFORE CALLING FOR SERVICE
Before contacting professional service, please review the trouble shooting list
that includes common occurrences that are not the result of a defect in
workmanship or materials.
Problem Possible Cause Solution
Not working
No power supply Connect to a functioning outlet and switch on
Water Full Indication Flashes
Drain water tank and reset it, or re-position the
water tank to proper place
Room temperature ˂ 41℉, or ˃ 95℉
Self-Protection de
signed to protect the unit.
The unit cannot work under such temperature
Bad functioning
Is the air filter clogged? Clean the air filter as instructed
Is the intake duct or discharge duct
obstructed?
Remove the obstruction from the discharge
duct or intake duct.
No air intake Is the filter clogged? Wash the filter
Loud noise
when running
Is the machine put in the flat place? Put the machine on the flat ground
Is the filter clogged? Wash the filter
E2 Humidity sensor problem Change a sensor
LO Environmental humidity is below 35%
The dehumidifier shuts down for self-
protection
HI Environmental humidity is above 95%
CL
Low temperature protection, the
environmental temperature＜41℉
CH
High temperature protection, the
environmental temperature＞95℉