User Card

English
Standalone transponder module
DANGER
Dangerous currents flow through the body when coming
into direct or indirect contact with live components. This
can result in electric shock, burns or even death. Work
improperly carried out on current-carrying parts can cause
fires.
– Disconnect the mains voltage prior to mounting and
dismantling!
– Permit work on the 100-240 V mains network to be
carried out only by specialist staff.
■
Please read the mounting instructions carefully and keep them for
future use.
■
Additional user information and information about planning is
available at http://new.abb.com/low-voltage/products/building-
automation/product-range/abb-welcome or by scanning the QR
code.
Intended use
This device is a central control panel of the ABB-Welcome system
and operates exclusively with components from this system.
Manufacturer
ABB Xiamen Smart Technology Co., Ltd.
Address: No.7 Fangshan South Road, Xiang An, Xiamen, Fujian,
China
Post Code: 361000
Technical data
Input (a, b)
24 V ⎓
Operating voltage
range
20-30 V ⎓
Standby current
24 V ⎓, 30 mA
Operating current
24 V ⎓, 30 mA
Operating temperature
-25 °C …+55 °C
Single-wire clamps
2 x 0.28 mm
2
...2 x 0.75 mm
2
Fine-wire clamps
2 x 0.28 mm
2
...2 x 0.75 mm
2
IP level
IP 54
IK level
IK 07
Carrier frequency:
13.56MHz
Carrier filed
strength:
-1.36dBµA/m @ 3m
FCC ID: 2AEBL-M2700TP
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
The complete of FCC information is available at the package shipped
with the product.
EU declaration of conformity
Hereby, ABB Xiamen Smart Technology Co., Ltd., declares that this
Standalone transponder module M2700TP is in compliance with the
essential requirements and other relevant provisions of RE Directive
2014/53/EU. The complete of the EU declaration of conformity is
available by scanning the QR code.
Operation
1
Swiping card position
Empty status
If this module has not enrolled any card, it will enter "Empty status"
when it is powered on. Transponder module flash in green, orange
and red.
Function
Operation
Note
Create the first admin
card
Swipe the card 1x
Transponder LED
light green if
successful
Standby status
If this module has enrolled the card, it will enter "Standby status"
when it is powered on.
Function
Operation
Note
Open a door
Swipe the
enrolled card
1. Lock is connected with
switch actuator
2. Switch actuator works in
"door opener" mode
3. Switch actuator's address =
transponder module address(1-
32)
Setting mode status
On standby status, Swipe the enrolled card (any admin) 1x to enter
setting mode status, Transponder module light orange.
Function
Operation
Create a user card
Swipe any admin card 1x + user card1 + user
card2 + …
Delete a user card
Swipe any admin card 2x + user card1 + user
card2 + …
Create admin cards
Swipe admin0 3x + admin card1 + admin
card2 + …
*Here, admin0 can be replaced by any
enrolled admin.
Delete admin cards
Swipe any admin card 4x + admin card1 +
admin card2 + …
*Any admin card can’t delete itself.
Delete all user
cards
Swipe any admin card 6x
Transponder module light green if successful.
Connection
1
Plug-in clamps (a - b) for bus connection and power input
2
Terminal resistor
In video installations or mixed audio and video installations,
the Switch must be set as 'RC on' on the last device of the
line.
3
Set the address of this device (1...32)
4
N/A