- Power Supply User's Guide

ManualsBrandsAB Soft ManualsPower SupplyATX 12V

• Please read the users guide before proceeding with your

installations. Serious damage may occur if the procedure is not

followed properly.

•

This motherboard does not support CPUs with a Vcore higher than 1.6

volts. Please make sure the CPU you are using 1.6 volts or below.

Check the CPU specification before you insert it in the CPU socket.

• AGP cards running at 3.3v are not supported. Only AGP cards running

at 1.5v (most 4x or 8x AGP cards) are supported on this motherboard.

•

Please make sure that your memory modules are inserted correctly.

They can go in only one way, and should fit completely in the socket

without sticking out. Failure to do so will damage your motherboard

and memory module.

•

An ATX 12V power supply (Power supply for Pentium 4 system) is

required for the system to operate normally. (Preferably 350 watts for

minimal loading or 400 watts for fully loaded system).

• If you have any problem getting your system to work, please follow the

troubleshooting tips in your user manual.

•

On some motherboards, the actual chipset cooler may differ from the

chipset cooler as shown on the picture or on the box. However, the

chipset fan on the motherboard is of the same quality and will work just

as well as the one shown in the picture. (The chipset cooler is as

sufficient as the chipset fan based on a different design.)

•

For answers to Technical questions, please visit SOYO tech support

link at http://www.soyousa.com/support

and

http://www.soyousa.com/kb.

Summary of content (97 pages)

PAGE 1
• Please read the users guide before proceeding with your installations. Serious damage may occur if the procedure is not followed properly. • This motherboard does not support CPUs with a Vcore higher than 1.6 volts. Please make sure the CPU you are using 1.6 volts or below. Check the CPU specification before you insert it in the CPU socket. • AGP cards running at 3.3v are not supported. Only AGP cards running at 1.5v (most 4x or 8x AGP cards) are supported on this motherboard.
PAGE 2
SY-P4I865PE Plus DRAGON 2 Motherboard **************************************************** mPGA Socket 478 Processor supported Intel 865PE AGP/PCI 400/533/800 MHz Front Side Bus supported ATX 12V Form Factor **************************************************** User's Manual
PAGE 3
SOYO™ SY-P4I865PE Plus DRAGON 2 Copyright © 2003 by Soyo Computer Inc. Trademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyrights belong to their respective companies. Copyright Notice: All rights reserved. This manual has been copyrighted by Soyo Computer Inc.
PAGE 4
SY-P4I865PE Plus DRAGON 2 Table of Contents Table of Contents CHAPTER 1 MOTHERBOARD DESCRIPTION ............................... 1 1-1 INTRODUCTION ........................................................................ 1 1-2 UNPACKING THE MOTHERBOARD ....................................... 1 1-3 KEY FEATURES.......................................................................... 3 1-4 HANDLING THE MOTHERBOARD .........................................
PAGE 5
SY-P4I865PE Plus DRAGON 2 Table of Contents 3-4 ADVANCED CHIPSET FEATURES ......................................... 63 3-5 INTEGRATED PERIPHERALS ................................................ 65 3-6 POWER MANAGEMENT SETUP............................................ 71 3-7 PNP/PCI CONFIGURATION SETUP........................................ 75 3-8 PC HEALTH STATUS................................................................ 78 3-9 LOAD FAIL-SAFE DEFAULTS .....................................
PAGE 6
SY- P4I865PE Plus DRAGON 2 Hardware Installation Chapter 1 MOTHERBOARD DESCRIPTION 1-1 INTRODUCTION The SY-P4I865PE Plus DRAGON 2 AGP/PCI Motherboard is a high-performance Socket 478 processor supported ATX 12V form-factor system board. SY-P4I865PE Plus DRAGON 2 uses the Intel 865PE Chipset technology. This Motherboard is fully compatible with industry standards and adds many technical enhancements.
PAGE 7
SY- P4I865PE Plus DRAGON 2 Hardware Installation One Back panel Warning: Do not unpack the Motherboard from its anti-static packaging until you are ready to install it. Like most electronic equipment, your Motherboard may be damaged by electrostatic discharge. To avoid permanent damage to components ground yourself while working by using a grounding strap. Otherwise, ground yourself frequently by touching the unpainted portion of the computer chassis to drain the static charges.
PAGE 8
SY- P4I865PE Plus DRAGON 2 Hardware Installation 1-3 KEY FEATURES CPU Supports Intel® mPGA Socket 478 processors : Pentium® 4 with and without Hyperthreading, Northwood, Prescott (400/533/800MHz FSB) Pentium® 4 Celeron SOYO COMBO Setup CMOS setup menu for complete and easy changing of your CPU settings in CMOS setup, making jumpers obsolete. Note: CPUs with higher than 1.6 volts are not supported.
PAGE 9
SY- P4I865PE Plus DRAGON 2 Hardware Installation Storage USB 2.0 Sound Network BIOS Industry standards ICH5 integrated Serial ATA controller supporting up to 2x UDMA 150 hard disks ICH5 Integrated Parallel ATA controller supporting up to 4x UDMA 33/66/100 Parallel ATA devices. 8 x USB 2.0 compliant ports (4 on rear IO panel, 4 x motherboard connectors.
PAGE 10
SY- P4I865PE Plus DRAGON 2 Hardware Installation Warning: Do not apply power if the Motherboard appears damaged. If there is damage to the board, contact your dealer immediately. 1-5 ELECTROSTATIC DISCHARGE PRECAUTIONS Make sure to ground yourself before handling the Motherboard or other system components. Electrostatic discharge can easily damage the components. Note that you must take special precautions when handling the Motherboard in dry or air-conditioned environment.
PAGE 11
SY- P4I865PE Plus DRAGON 2 Hardware Installation 1-6 SY-P4I865PE PLUS DRAGON 2 MOTHERBOARD LAYOUT DDR_A1 DDR_A2 DDR_B1 PS/2 KB PS/2 Mouse Connector Connector USB COM A COM B PRT +12V Power USBLAN ATX Power MIC IN / Center & Bass out Audio out / Front out Audio in / Rear out IDE 2 AGP Slot 5 2 1 IDE 1 FDC1 J30 6 DAVICOM DM9102AE PCI Slot #1 AC97 codec JP5 PCI Slot #2 1 4 1 AUX_IN1 4 CMOS Clear Jumper SATA2 PCI Slot #3 CDIN1 SATA1 3V Lithium Battery PCI Slot #4 ITE IT8712F PCI
PAGE 12
SY- P4I865PE Plus DRAGON 2 Hardware Installation 1-7 SY-P4I865PE PLUS DRAGON 2 MOTHERBOARD COMPONENTS A B C D E F G H I AE J AD K AC L AB M N AA O P Z Q Y X W V U 7 T S R
PAGE 13
SY- P4I865PE Plus DRAGON 2 Hardware Installation A B C D E F G +12V Power Connector This is where the Power Supply's +12V ATX connector goes. For a lay-out of this connector please check the F. ATX12V Power Supply paragraph on page 35. ATX Power Supply connector This connector is to connect the ATX connector of your ATX12V compliant power supply to the motherboard. For more details on this connector, please check the F. ATX12V Power Supply paragraph on page 35.
PAGE 14
SY- P4I865PE Plus DRAGON 2 Hardware Installation H I J K L M N CPU Cooling Fan (CPUFAN1) connectors With these connectors you can attach the CPU fan or fans to your motherboard. They supply power and (in the case of CPUFAN1) allow you to monitor the speed of the FAN via the SOYO Hardware Monitor software or via CMOS setup.
PAGE 15
SY- P4I865PE Plus DRAGON 2 Hardware Installation O P Q R S T U Chassis Cooling Fan (CHAFAN1) connector This connector is to connect your chassis fan to your motherboard. This motherboard supports up to 2 chassis fans. It allows you to monitor the speed of CHAFAN1 in CMOS setup or by using the SOYO Hardware Monitor software. Please check the (2) Chassis Cooling Fan (CHAFAN1, CHAFAN2) paragraph on page 31 for more details.
PAGE 16
SY- P4I865PE Plus DRAGON 2 Hardware Installation V W X Y Z AA AB GAMEPORT connector This connector is to attach your gameport connector to. Gameports are used to connect for example joysticks to. For more details check the paragraph on page 30. Serial Infrared (IrDA) device header This header allows you to connect an IrDA receiver to the motherboard. You can find the lay-out in the 1. Standard Infrared (SIRCON) paragraph on page 30.
PAGE 17
SY- P4I865PE Plus DRAGON 2 Hardware Installation AC AD AE AC97 Onboard Audio Chip Microphone and LAN Status LED Connector (J30) This connector allows you to extend your microphone connector and LAN Status LED to your front panel. Check the 6. MIC & LED Connector (J30) paragraph on page 34 for a lay-out of this header. Back panel connectors These connectors allow you to attach the external devices to the back of your PC. Please check the D. Back Panel Connections paragraph on page 26 for more details.
PAGE 18
SY- P4I865PE Plus DRAGON 2 Hardware Installation Chapter 2 HARDWARE INSTALLATION Congratulations on your purchase of SY-P4I865PE Plus DRAGON 2 Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti-static packaging until you have made the following preparations. 2-1 PREPARATIONS Gather and prepare all the following hardware equipment to complete the installation successfully: 1.
PAGE 19
SY- P4I865PE Plus DRAGON 2 Hardware Installation 2-2 INSTALLATION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Step1- Install the Central Processing Unit (CPU). Step2- Install memory modules. Step3- Install expansion cards. Step4- Connect cables, case wires, and power supply. Step5- Power on and enter BIOS setup . Step6- Install supporting software tools.
PAGE 20
SY- P4I865PE Plus DRAGON 2 Hardware Installation 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without forcing.
PAGE 21
SY- P4I865PE Plus DRAGON 2 Hardware Installation 4. Then close the socket handle to secure the CPU in place. Remember to connect the CPU Cooling Fan to the appropriate power connector on the Motherboard. The fan is a key component that will ensure system stability. The fan prevents overheating, therefore prolonging the life of your CPU. CPU Fan Installation Your Socket 478 processor kit comes with a cooling fan. Mount the fan on the processor according to the instructions provided by the manufacturer.
PAGE 22
SY- P4I865PE Plus DRAGON 2 Hardware Installation Step 2 Install Memory Module DDR_A1 DDR_A2 DDR_B1 This motherboard supports one Dual Channel to your memory, Note that you can use normal DDR memory for Dual Channel to work. Also note that for Dual Channel to work 2 modules of equal size and specifications have to be installed. The largest memory capacity possible is 3 GB. On this motherboard, DRAM speed can be set independent form the CPU front side bus speed.
PAGE 23
SY- P4I865PE Plus DRAGON 2 Hardware Installation Memory Configuration Table If you want to use the Dual Channel feature, please follow the memory configuration table below: DDR Slots DDR_A1 DDR_A2 DDR_B1 Performance 128 bit Present Present Installing your memory in a combination different from the table above will still allow your system to work. The Dual Channel feature will not work then however.
PAGE 24
SY- P4I865PE Plus DRAGON 2 Hardware Installation Step 3 Installation of Expansion Cards The motherboard has 1 AGP slot and 5 PCI slots. 1. Read the related expansion card’s instruction document before inserting the expansion card into the computer. 2. Press the expansion card firmly into the expansion slot in the motherboard. 3. Make sure the metal contacts on the card are seated in the slot. 4. Replace the screw to secure the slot bracket of the expansion card. 5.
PAGE 25
SY- P4I865PE Plus DRAGON 2 Hardware Installation Step 4 Connect cables, case wire, and power supply A.IDE Device Installation (HDD, CD-ROM) Pin 1 IDE 2 Secondary IDE IDE 1 Primary IDE SATA2 SATA1 This Motherboard offers 1 primary (IDE1) IDE device connectors, 1 secondary IDE device connectors (IDE2) and 2 tertiary serial ATA ports. IDE1 and IDE2 can support up to four high-speed Ultra DMA 33/66/100 HDD or CD-ROM. SATA1~2 can support up to 2 ATA 150 SATA hard disks.
PAGE 26
SY- P4I865PE Plus DRAGON 2 Hardware Installation Note: IDE2 and SATA2 are not bootable, SATA1 and IDE1 are bootable. Note: Only Windows XP can use SATA1, SATA2, IDE1 and IDE2 at the same time. All other operating systems can use any combination from the following table: Parallel ATA connectors Connect the black end of the ATA66/100 flat cable to the IDE device (HDD or CD-ROM) and plug the blue end to the primary (IDE1) or secondary (IDE2) directionally keyed IDE connector on the Motherboard.
PAGE 27
SY- P4I865PE Plus DRAGON 2 Hardware Installation Serial ATA connectors You can also plug the serial ATA cable into the serial ATA connector of the motherboard. The other end of the SATA cable goes into your SATA device.
PAGE 28
SY- P4I865PE Plus DRAGON 2 Hardware Installation B. Floppy Drive Installation Pin 1 FDC Floppy Drive Connector The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan. Connect one side of the 34-pin flat cable to the floppy drive and plug the other end in the floppy drive connector on the Motherboard. This Motherboard can supports only 1 floppy drive.
PAGE 29
SY- P4I865PE Plus DRAGON 2 Hardware Installation + _ ACPI LED Key Lock 1 1 PWRBT + _ Power LED + _ _ Speaker HDD LED + C. Front Panel Connections 1 Reset Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED Please install according to the following pin assignment: pin 1, 3 are for Power LED.
PAGE 30
SY- P4I865PE Plus DRAGON 2 Hardware Installation 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. Reset Pin Assignment Pin1 Pin2 Power Good GND 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard. Speaker Pin Assignment _ + VCC Speaker out NC NC 4.
PAGE 31
SY- P4I865PE Plus DRAGON 2 Hardware Installation 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE1 or IDE2 (HDD, CD-ROM) device is active. HDD LED Pin Assignment Pin9 + _ Pin10 LED Cathode LED Anode 6. ATX Power On/Off Switch Attach the 2-pin momentary type switch to the PWRBT header for turning On or Off your ATX power supply.
PAGE 32
SY- P4I865PE Plus DRAGON 2 Hardware Installation D. Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly into the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices. When connecting an external device, use the following figure to locate and identify which back panel connector to plug the device to.
PAGE 33
SY- P4I865PE Plus DRAGON 2 Hardware Installation 1. Onboard Serial Ports COMA/COMB External peripherals that use serial transmission scheme include: - serial (RS232) mice - modem. Plug the serial device cables directly into the COMA/COMB 9-pin male connectors located at the rear panel of the Motherboard. 2. Parallel Port PRT This parallel port is used to connect the printer or other parallel devices.
PAGE 34
SY- P4I865PE Plus DRAGON 2 Hardware Installation 5. Universal Serial Bus (USB1/USB2, USB3/USB4, USB20_1/USB20_2) This Motherboard provides 8 USB 2.0 ports for your additional devices. Plug the USB device jack into the available USB connector USB1, USB2, USB3 and USB4. USB20_1 and USB20_2 are available. To make use of these USB ports, purchase a USB cable from your dealer.
PAGE 35
SY- P4I865PE Plus DRAGON 2 Hardware Installation The Gameport has the following lay-out : E. Other Connections 1. Standard Infrared (SIRCON) Plug the 5-pin infrared device cable to the SIRCON header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications.
PAGE 36
SY- P4I865PE Plus DRAGON 2 Hardware Installation 2. Cooling Fan Installation (1) CPU Cooling Fan (CPUFAN1) After you have seated the CPU properly on the processor, attach the 3-pin fan cable to the CPUFAN connector on the Motherboard.
PAGE 37
SY- P4I865PE Plus DRAGON 2 Hardware Installation (2) Chassis Cooling Fan (CHAFAN1, CHAFAN2) Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector.
PAGE 38
SY- P4I865PE Plus DRAGON 2 Hardware Installation 3. Smart Card Reader The smart card reader conforms to the PC/SC Working group standard, and has the following lay-out: 4. CD Line-in (CDIN1) This Motherboard provides one CD-Line-in connectors. Please connect the 4-pin audio cable from your CD-ROM or DVD ROM drive to CDIN1.
PAGE 39
SY- P4I865PE Plus DRAGON 2 Hardware Installation 5. AUX-IN (AUXIN1) This Motherboard provides one AUX-IN connectors. Please connect the 4-pin audio cable from your second CD-ROM or DVD ROM drive to either AUX-IN. Please install according to the following pin assignment: AUXIN1 Pin Assigment 1 2 3 4 GND Left Right GND 6. MIC & LED Connector (J30) You can connect the Line-out /MIC in /LAN LED to the front panel of your PC case (If this option is available in your PC case).
PAGE 40
SY- P4I865PE Plus DRAGON 2 Hardware Installation F. ATX12V Power Supply The power supply connector is the last connection to be made while installing a motherboard. This motherboard requires an ATX 12V power supply (For P4 system), and AT or ATX power supply cannot be used. +12V Power ATX Power Note 1: The presence of the +12V power connector indicates that a power supply is ATX12V; the absence of the +12V power connector indicates that a supply is ATX.
PAGE 41
SY- P4I865PE Plus DRAGON 2 Hardware Installation Note 3: The minimum recommended wattage is 400W for a fully loaded system or 350W for a minimally loaded system, the system might become unstable if power supply is not enough Note 4: The 4 pin ATX 12V must be connected to the motherboard. Without this connector, the system cannot boot. Please install the ATX power according to the following pin assignment: ATX Power 12V 5VSB PW-OK GND 5V 5V -5V GND GND GND PS-ON GND -12V 3.3V 5V GND 5V GND 3.3V 3.
PAGE 42
SY- P4I865PE Plus DRAGON 2 Hardware Installation G. CMOS Clear (JP5) CMOS Clear (JP5) Pin Assignment GND RTC NC In some cases the CMOS memory may contain wrong data, follow the steps below to clear the CMOS memory. 1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper can be easily identified by its white colored cap. 2. Then put the jumper back to 1-2 to allow writing of new data into the CMOS memory.
PAGE 43
SY- P4I865PE Plus DRAGON 2 Hardware Installation Onboard LAN LED Definition When this LED is lit, this This is the LAN activity means LED. It will blink when the LAN is running at 100 mbps, if it it is active. is not lit, the Onboard LAN is working at 10 mbps. Step 5 Power On You have now completed the hardware installation of your Motherboard successfully. 1. Turn the power on 2.
PAGE 44
SY- P4I865PE Plus DRAGON 2 Hardware Installation Repeat this operation until you get the following screen. 3.
PAGE 45
SY- P4I865PE Plus DRAGON 2 Hardware Installation Step1. Select [STANDARD CMOS SETUP] Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”. Step2. Select [LOAD OPTIMIZED DEFAULTS] Select the “LOAD OPTIMIZED DEFAULTS” menu and type “Y” at the prompt to load the BIOS optimal setup. Step3. Select [SOYO COMBO FEATURE] Set the [CPU Frequency Select] field to “Manual”, to be able to change the CPU frequency 1 MHz stepping. Step4.
PAGE 46
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
PAGE 47
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command F1 F5 F6 F7 F10 [Esc] [Enter] [+/–/PU/PD] Description Gives the list of options available for each General Help item. Previous Restore the old values. These are the values Values that the user started the current session with. Load Loads all items with the most conservative Fail-Safe values.
PAGE 48
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility SAVE AND EXIT SETUP Select the [SAVE & EXIT SETUP] option from the Main Menu to save data to CMOS and exit the setup utility. This option saves all your changes and causes the system to reboot. R O M C M O S A W A R D S T A N D A R D B IO S C H IP S E T P O W C M O S F E A T U R E S E R P C I/ IS A B IO S S E T U P U T IL IT Y S O F T W A R E , IN C .
PAGE 49
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-1 SOYO COMBO FEATURE This motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO Feature]. After the hardware installation is complete, turn the power switch on, then press the ~~key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will display on screen.~~
PAGE 50
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility System Performance Setting System Performance Normal Fast Turbo Description Adjust your computer’s performance. Note Default SOYO COMBO Feature Setting Description Note CPU Clock Ratio 8X~ 50X The available CPU ratio you can select will depends on your CPU ID. CPU Frequency Select Manual Auto Choose the pre-defined CPU frequency setting or auto for auto Default detecting your CPU frequency.
PAGE 51
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility SOYO COMBO Feature (Continue) Setting Quick Power On Self Test Description Note Disabled Enabled C.I.H. 4-WAY Enabled Protection Disabled Provides a fast POST at boot-up. Default This item allows you write-protect your BIOS chip. If you want to Default flash your BIOS, set this option to disabled. Write protecting your BIOS protects you against some viruses. Voltage Select Setting Description Note CPU Vcore Select Default 1.600 1.550 1.500 1.450 1.
PAGE 52
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-1.1 Advanced DRAM Control Caution: Change these settings only if you are already familiar with DRAM timing parameters. The [Advanced DRAM Control] option changes the values of the chipset registers. These registers control the timings of your memory. Phoenix – Award BIOS CMOS Setup Utility Advanced DRAM Control DRAM Timing Selectable By SPD x CAS Latency Time 2.
PAGE 53
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility CHIPSET FEATURES SETUP (Continue) Setting DRAM RAS# to 2 CAS# Delay 3 4 DRAM RAS# Precharge Refresh Mode Select Description Note This item allows you to control DRAM RAS to CAS delay time. Default 2 3 4 This item allow you to control DRAM RAS percharge time. 7.8 us 15.6 us 64 us Auto This item allows you to set the interval between consecutive refresh cycles.
PAGE 54
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-1.2 Onboard Device The [Onboard Device] option changes the values of the chipset registers. These registers control the system options in the computer.
PAGE 55
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-1.3 OnChip IDE Device Caution: Change these settings only if you are already familiar with the IDE settings. The [OnChip IDE Device] option changes the settings of the 82801EB (ICH5) IDE controller. These settings do not influence the HighPoint 372N or Silicon Image Sil3112 controllers. The following screen shows setup default settings.
PAGE 56
BIOS Setup Utility SY- P4I865PE Plus DRAGON 2 CHIPSET FEATURES SETUP Setting Description IDE 1,2 /SATA 1,2 IDE only SATA only Pri IDE+SATA SATA+Sec IDE IDE + SATA IDE HDD Block Mode Disabled Enabled Only enabled IDE1,2. Default SATA1,2 are disabled Only enable SATA1,2. IDE1,2 are disabled. IDE1 and SATA1,2 are enabled. IDE2 is disabled. IDE2 and SATA 1,2 are enable. IDE1 is disabled. IDE1,2 AND sata1,2 are all enabled. Invokes multi-sector transfer instead of one sector per transfer.
PAGE 57
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility IDE Device Controls Setting Description Note On-Chip PCI IDE Primary Secondary Disabled Turn off the on-board IDE Use the on-board IDE Default IDE mode 0-4 Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO IDE Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA Enabled 0 is the slowest speed 4 is the fastest speed For better performance Default and stability, we suggest you use the Auto settin
PAGE 58
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-1.4 Boot Device Order The [Boot Device Order] option allows you to change the order in which your system scans for devices to boot from. Note: That SATA 1 and SATA 2 are not bootable. Phoenix – Award BIOS CMOS Setup Utility Boot Device Order First Boot Device Second Boot Device Third Boot Device Boot Other Device Floppy IDE1/SATA1 LS120 Enabled Item Help Menu Level Allows the system to skip certain tests while booting.
PAGE 59
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility System Boot Control Settings Setting Description First Floppy /Second/Third LS120 Boot Device IDE1/SATA1 CDROM ZIP100 Other Device Disabled Boot Other Device Note Selects the order in which your system scans for devices to boot from (First the first boot device, then the second, etc…). For booting from the HighPoint 372N or Silicon Image Sil3112 controller, set this option to SCSI).
PAGE 60
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. Phoenix – Award BIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Mon, May 7 2003 2 : 30 : 20 Item Help Menu Level IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave None None None None Change the day, month, year and century. Drive A Floppy 3 Mode Support 1.44M, 3.5 in.
PAGE 61
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary Setting Description Note (Secondary) Master & Slave IDE HDD Auto-Detection Press Enter To auto-detect the HDD’s size, head… on this channel IDE Primary Slave (User Type) Auto BIOS detects hard disk type Default automatically. User defines the type of hard disk. Access Mode Auto User None CHS LBA Large BIOS detects hard disk mode automatically.
PAGE 62
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Others Optional Setting Description Note Video EGA/VGA CGA 40 CGA 80 MONO (Monochrome) Select the video mode. Halt On ALL Errors No Errors All, But Keyboard All, But Diskette All, But Disk/Key When the BIOS detects system Default errors, this function will stop the system. Select which type of error will cause the system halt.
PAGE 63
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-3 ADVANCED BIOS FEATURES Select the [Advanced BIOS Features] option from the Main Menu and press [Enter] key.
PAGE 64
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Virus Warning Setting Virus Warning Disabled Enabled Description Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Sound a warning beep.
PAGE 65
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Boot Up NumLock Status Setting Boot Up NumLock Status On Description Numeric keypad in numeric mode Default at boot-up. Puts numeric keypad in arrow key mode at boot-up. Off Gate A20 Options Setting Gate A20 Options Normal Fast Note Description A pin in the keyboard controller controls GateA20. Lets chipset control GateA20.
PAGE 66
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. The following table describes the security settings. Setting Security Option Setup System APIC Mode Description If a password is set, the password Default prompt only appears when you attempt to enter the BIOS Setup program. If a password is set, prompt appears both when entering CMOS setup and during system POST.
PAGE 67
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility LOGO Show Setting Description Note Full Screen LOGO Show Disabled Enabled Set Enabled to Show Logo (DRAGON). EPA LOGO SELECT LOG0 LOG1 Allows user to display SOYO Default logo or own logo. Logo-0 shows SOYO logo, Logo-1 shows user logo. Small Logo(EPA) Show Disabled Enabled Set Enabled to Show Logo(EPA).
PAGE 68
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-4 ADVANCED CHIPSET FEATURES Caution: Change these settings only if you are already familiar with the Chipset. The [Advanced Chipset Features] option changes the values of the chipset registers. These registers control the system options in the computer.
PAGE 69
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility CHIPSET FEATURES SETUP Setting Description System BIOS Disabled Cacheable Enabled The ROM area F0000H-FFFFFH is cacheable. Note Default Video BIOS Cacheable Disabled Enabled The video BIOS area at C0000H-C7FFFH is cacheable. Delay Prior to Thermal 4Min 8Min 16Min 32Min Set the time for the system to decrease performance to avoid reaching maximum thermal temp. Ex.
PAGE 70
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-5 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer. The following screen shows setup default settings.
PAGE 71
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-5.1 Onboard USB Device This [Onboard USB Device] option changes the values of the onboard USB controller. The following screen shows setup default setting. Phoenix – Award BIOS CMOS Setup Utility Onboard USB Device USB Controller USB 2.
PAGE 72
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-5.2 SuperIO Device Caution: Change these settings only if your are already familiar with the Chipset. The [SuperIO Device] option changes the values of the Super I/O controller. The following screen shows setup default settings.
PAGE 73
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Others Optional Setting Description POWER ON Password Function Hot KEY Mouse Move Mouse Click Any KEY Note Enables you to wake-up the system by entering a password on the keyboard. You can wake-up the system by pressing the key combination of your choice (Ctrl-F1~F12). Enables waking up the system by pressing either the right or left mouse button. BUTTON-ONLY Disables the Wake-Up by Default Keyboard function.
PAGE 74
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Onboard Serial Ports Setting UART Mode Select Description Normal IrDA ASKIR SCR Note Default The second serial port offers several special modes. It can either work as an infrared device (IrDA, ASKIR) or as a Smart Card reader (SCR), or as a normal serial port. If [UART Mode Select] is set to [IrDA]/[ASKIR] UR2 Duplex Mode Half Full Choose [Half] or [Duplex] to set Default UR2 in half duplex mode or full duplex mode respectively.
PAGE 75
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Others Optional Setting PWRON After PWR-Fail Note On The system will switch on when power comes back after a power failure. Off The system will remain off Default when power comes back after a power failure. Former-Sts The system will return to the state it was in before the power failure when power returns. (i.
PAGE 76
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-6 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions.
PAGE 77
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Power Management Controls Setting Description ACPI Suspend S1(POS) Type S3(STR) S1 & S3 This item allows you select suspend mode. Note Default Run VGABIOS if S3 Resume Auto Yes No Some OS (win xp/2k) require Default to load VGABIOS after resume from S3. Power Management User Define Lets you define the HDD and Default system power down times.
PAGE 78
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Power Management Controls (Continue) Setting Description Note HDD Power Down Disabled 1-15Min Soft-Off by PWR-BTTN Instant-off Turns off the system power instant after pushing the power button. Delay 4 Turns off the system power 4 Sec. seconds after pushing the power button. Default Wake-Up by PCI card Disabled Enabled Default Power On by Ring Disabled Enabled When the set time has elapsed, BIOS sends a command to the HDD to power down.
PAGE 79
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Reload Global Timer Events Setting Description IDE0, IDE1 Primary Secondary FDD, COM, LPT Port Disabled Enabled Disabled Enabled PCI PIRQ [A-D]# Disabled Enabled Note Default In effect, the system remains alert for anything which occurs to a device which is configured as Enabled. Default In effect, the system remains alert for anything which occurs to a device which is configured as Enabled. Default The system monitors these elements for activity.
PAGE 80
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-7 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI configuration.
PAGE 81
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility PNP/PCI Configuration Controls Setting Description Reset Configuration Data Note Disabled Retain PnP configuration Default data in BIOS. Enabled Reset PnP configuration data in BIOS. Resources Controlled By Manual BIOS does not manage PCI/ISA PnP card IRQ assignment. Required to assign IRQ-# and DMA-# to PCI or ISA PnP manually.
PAGE 82
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility PNP/PCI Configuration Setup (Continued) Setting Description Note Interrupt Line IRQ 15 IRQ 14 How to set the BIOS to release the IRQ to the PnP Interrupt pool: PnP / PCI configuration Integrated Peripherals IRQ 15: PCI / ISA PnP On-Chip Secondary PCI IDE: disabled IRQ 14: PCI / ISA PnP On-Chip Primary PCI IDE: disabled Interrupt 12 will be released by the PnP IRQ 12 IRQ 12: PCI / ISA PnP BIOS automatically if the PS/2 Mouse Port is not used.
PAGE 83
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-8 PC HEALTH STATUS This option sets the Motherboard's PC Health Status. Phoenix – Award BIOS CMOS Setup Utility PC Health Status CPU Vcore +3.3V +5V +12V DRAM Voltage AGP Voltage CPU Temperature CHA Temperature 1.72 V 3.21 V 5.02 V 11.77 V 2.59 V 1.
PAGE 84
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-9 LOAD FAIL-SAFE DEFAULTS Select the [Load Fail-Safe Defaults] option from the Main Menu to load a pre-defined safe bios settings. This option is recommended if you have instability issues.
PAGE 85
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-10 LOAD OPTIMIZED DEFAULTS Select the [Load Optimized Defaults] option from the Main Menu to load the pre-defined optimized BIOS settings.
PAGE 86
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3-11 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [Advanced BIOS Feature] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1. Choose [Advanced BIOS Feature] in the Main Menu and press [Enter]. Select the [Security Options] item and set the field to: a.
PAGE 87
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: Confirm Password: 4. Re-enter your password and then press [Enter] to exit to the Main Menu.
PAGE 88
SY- P4I865PE Plus DRAGON 2 BIOS Setup Utility Boot Menu Boot Menu enables user to boot-up on different boot device without going into the BIOS setup. To enable boot Menu, press “ESC” after memory and option ROM (like the HighPoint 372N BIOS) initialization, the user will see a device menu, in which he or she can choose from which device they wish to boot.
PAGE 89
SY- P4I865PE Plus DRAGON 2 Drivers installation Chapter 4 DRIVERS INSTALLATION The SOYO-CD will Auto Run only in Windows Based Operating Systems. Your SY-P4I865PE Plus DRAGON 2 Motherboard comes with a CD-ROM labeled “SOYO CD”. The SOYO CD contains a. The user’s manual for your new motherboard in PDF format, b. The drivers software available for installation, and c. A database in HTML format with information on SOYO motherboards and other products. Step 1.
PAGE 90
SY- P4I865PE Plus DRAGON 2 Drivers installation The user's manual files included on the SOYO CD are in PDF (Postscript Document Format). In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system. Note: The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and otherwise prompts you on whether or not you want to install it. You must install the Acrobat Reader utility to be able to read the user's manual file.
PAGE 91
SY- P4I865PE Plus DRAGON 2 Drivers installation Step 2. Install Drivers and Utilities Highlight the driver you want to install and then click ok. The Start Up program displays the drivers available for the particular model of Motherboard you own. We recommend that you only install those drivers Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard.
PAGE 92
SY- P4I865PE Plus DRAGON 2 Drivers installation C-MEDIA Audio Driver for Win 9x/ME/2000/NT/XP The driver supports 2/4/6 speakers 3D positional audio. P4I865PE DRAGON 2 hardware monitor for Win 9x/ME/2000/NT/ XP Your motherboard comes with a hardware monitoring IC. By installing this utility Temperatures, Fan speeds and Voltages can be monitored. ITE SIM Card reader Driver/Utility for Win 9X/ME/NT/2K/XP Driver to support the smart card reader. You need to install this if you use the SCR.
PAGE 93
SY- P4I865PE Plus DRAGON 2 Drivers installation After Windows XP installation, your device manager should look like this: 88
PAGE 94
SY- P4I865PE Plus DRAGON 2 Drivers installation After driver installation, your Windows XP device manager should look like this: Note: To install the USB 2.0 driver, please update to Windows XP service pack 1. Check chapter 5 for more info.
PAGE 95
SY- P4I865PE Plus DRAGON 2 Drivers installation Drivers directory list in the CD driver 90
PAGE 96
SY- P4I865PE Plus DRAGON 2 Intel USB 2.0 Driver Installation Chapter 5 INTEL USB 2.0 DRIVER INSTALLATION For Windows XP USB 2.0 drivers are available for download using Windows Update for Windows XP. For additional information regarding USB 2.0 support in Windows XP, please visit http://www.microsoft.com/hwdev/bus/USB/default.asp (Windows XP Service Pack1 Include USB2.0 Driver) After installing service pack1, please do the following: 1) Go into the device manager. 2) Remove ” ” 3) Restart your system.
PAGE 97
SY- P4I865PE Plus DRAGON 2 Intel USB 2.0 Driver Installation 10.Choose [Search for a suitable driver for my device]. 11.Click [Next]. 12.Choose [Specify a location] under "Optional search locations". 13.Click [Next]. 14.Click [Browse] to specify the file path where the driver is, e.g. "SOYO Dragon CD:\USB2.0\INTEL\2k\EHCI Package\". 15.Click [Next]. 16.Click [Finish].