AAVIX OUTDOORS 20V 20 INCH POLE/HANDHOLD HEDGE TRIMMER FOR SERVICE CALL: (USA)1-866-591-8921/(CANADA)1-514-885-0916 WARNING : To reduce the risk of injury, user must read this manual before assembling, operating and maintaining this unit. You are responsible for operating the product properly & safely. Version: V1.
WARNING! READ ALL INSTRUCTIONS BEFORE OPERATING! Follow all instructions. Save all warnings and instructions for future reference. These instructions below are for your safety. Please read them thoroughly before using. Familiarize yourself with them to reduce hazards like personal injuries and damage to property. TABLE OF CONTENTS Safety Rules.………………….…………………………………………..………………………………..2 Symbols.………………….………………………………………………………..…………………………8 Specifications.……….…………………………………………..
Personal Safety 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 2. This product is dangerous in the hands of untrained users. 3. Use personal protective equipment. Always wear eye protection.
Battery tool use and care 1. Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents. 2. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 3. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 4.
step on the battery or otherwise subject it to strong impacts or shocks. 14. Protect the battery pack against heat. Do not place the battery in direct sunlight or use or store the battery inside cars in hot weather. Doing so may cause the battery to generate heat, explode or ignite. 15. Never try to charge a battery pack that is cracked or damaged in any other way. There is a danger of electric shock or electrocution. 16. Under extreme conditions, battery leakage may occur.
charger from power source socket outlet and take away the battery pack from the charger, do not leave the battery pack in the charger. 12. Never carry the charger by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges. 13. Do not expose to water or rain, do not use in wet condition. 14. Do not open the charger. 15. Do not probe the charger. 16. Intended for indoor use only.Charge the battery pack indoors only. Hedge Trimmer Safety Warnings: 1.
20. Never attempt to force the blades to come to a standstill. 21. Do not put the tool down until the blade have come to a complete standstill. 22. Regularly check the blades for damage and wear. Do not use the machine when the blades are damaged. 23. Take care to avoid hard objects (e.g. metal wire, railings) when trimming. Should you accidentally hit any such object immediately switch the tool off and check for any damage. 24. Always be aware of falling debris when cutting the higher sides of a hedge. 25.
lubricated (where appropriate). - Plan your work schedule to spread any high vibration tool use across a longer period of time.Take frequent breaks. - If you detect any of the symptoms of the white finger syndrome, consult immediately with your doctor. Emergency Familiarise yourself with the use of this product by means of this instruction manual. Memorise the safety directions and follow them to the letter. This will help to prevent risks and hazards. 1.
Wear ear protection WARNING: Loud noise can cause severe hearing loss. Wear ear protection when operating this unit. Wear eye goggles. Thrown objects can cause severe eye injury.Wear eye protection meeting current ANSI / ISEA Z87.1 standards Wear safety helmet! Wear head protection when operating this unit; falling objects can cause severe head injury. Use a full face shield when needed. DO NOT USE IN THE RAIN WARNING: Avoid dangerous environments.
SPECIFICATIONS Model# A11704 Motor Voltage 20V Blade Length 20inch(508mm) Max. Cutting Diameter 3/4inch(19mm) Weight 10.3lbs(4.7kg) Protection Class / II Battery(Li-lon) Model# A112601 Max. Voltage＊ 20V Capacity 2.0Ah Charge Time Approx. 1hr Charger Model# A112701 Voltage Input 120VAC, 60Hz Voltage Output 20VDC, 2.
Know Your Product 1. Blade 2. Guard 3. Motor 4. Security Button 5. Front Handle 6. Lock Buckle 1 7. Rear Handle 8. Lock Switch 9. Trigger Switch 10. Battery Pack 11. Lock Buckle 2 12. Rear Hexagonal Alu. Pipe Joint 13. Belt Buckle 14. Auxiliary Handle 15. Telescopic Tube 16. Rotary Knob 17. Front Hexagonal Alu. Pipe Joint 18. Allen Key Set 19. Unlock Button Head Turn 20. Angle Ring 21. Unlock Button Head Rotation 22. Blade Sheath 23. Battery Charger Station 24. Battery Level Display Button 25.
The diagrams and pictograms herewith enclosed in this manual are a guide but not necessarily an exact copy of the actual product. INTENED USE 1. Your hedge trimmer has been designed for trimming hedges, shrubs and brambles. Do not use it for any other purposes. Do not use this product to cut plastic parts, bricks or construction materials. Do not use this product to move objects.Any other use could lead to dangerous situations. 2.
WARNING: Before assembly, remove the battery pack from the product. Your hedge trimmer is equipped with a battery pack, which powers the unit. The Guard Place guard as shown this Figure, Insert the 4pcs screws and tighten The Normal Hedge Trimmer: 1. Open the lock buckle1 of the front handle. 2. Insert the rear handle into the opening of front handle. 3. Lock the lock buckle1 of the front handle. The Pole Hedge Trimmer: 1. Unlock the lock buckle1 of the front handle. 2.
2. Move slide buckle to adjust the length of the shoulder strap. Adjust the length of the shoulder strap to obtain a comfortable working position. A few practices swings without starting motor should be made to determine correct balance. 3. Put the shoulder strap over your right shoulder. Carry the tool engine at the right side of your body. 4. If the shoulder strap is too close to your body, you can loose the hex screw with hex wrench, then push the lock ring further.
chipped, or damaged in any way. Do not operate the unit with loose, damaged parts or improperly adjusted. 2. Before start up, remove the security Blade Sheath from the blade. 3. Make sure the guard is well fixed to the product. The normal hedge trimmer Starting 1. Remove the blade sheath. 2. Place one hand on the rear handle. Place the other hand on the front handle. 3. Press the security button. 4. Continue to press the security button.
OPERATION locked in five positions (-90°, -45°, 0°, 45° and 90°). See below. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. Repair or replace everything you need before using the product. WARNING: It is strongly recommended that a comprehensive training course on machine use and engine operation be completed before attempting to use this machine. .
3. Screw the locking knob to lock the inner pole in place firmly. Charging The Battery Do not expose the battery to extreme condition such as heat impact. Risk of injury from escaping electrolytic solution.After eye/skin contact rinse the affected ares with water or a neutraliser and consult a doctor. Charge the battery in a dry room only . Check that the battery’s outer surface is clean and dry, before attaching the charger.there is a risk of injury due to electric shock.
3. Insert the battery pack into the charger station, making sure the pack is fully seated in the charger station. The LED lights is red to tell you that the battery pack is on charge. NOTE: Battery cannot be charged immediately after using the tool. The battery pack should be sufficiently cooled for a period of time. The LED lights changing from green to red means it can now be charged. 4. The battery pack will be fully-charged in about 1 hours.
charger before attempting to clean. 7. Do not immerse charger in water or any other liquid. WARNING! Don’t allow any liquid to get inside charger. Electric shock may result. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer. CAUTION! Never attempt to open the battery pack for any reason.
3. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control. 4. Do not force the hedge trimmer through heavy shrubbery. This can cause the blades to bind and slow down. If the blades slow down, reduce the pace. 5. DO not attempt to cut stems or twigs that are thicker than 3/4” (19 mm), or those obviously too large to feed into the cutting blade. Use a non-powered hand saw or pruning saw to trim large stems. 6.
the blade. WARNING: Read the safety information for safe operation using the blade. Extreme care must be taken when using blades to ensure safe operation. Refer to General Safety Rules and Specific Safety Rules. 13. Always start the hedge cutter before placing the blade in the cutting area. Once the hedge cutter has started, place the product in the hedge in a flat position and carry out long fan like movements. If you tilt the product in the cutting direction you will obtain better cutting results. 14.
forward when cutting higher hedge and the cutting area out of sight. 21. Do not to rush and do not attempt to cut too much with one stroke of the cutting blade. NOTE: Try to keep the cutting blade angled at approximately 15° to the cutting surface. 22. Cut in a number of stages if the area being cut is particularly long to achieve a better result; smaller cuttings will allow for easy composting. NOTE: When shaping it is advisable to achieve a trapezoidal shape.
2. Check for loose screws, nuts or bolts are tightly secured, (tighten as needed). 3. Check the blade sharpness. Cleaning After Each Use WARNING: Do not use chemical, alkaline,pine and lemon, abrasive or other aggressive detergents or disinfectants to clean this product. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. NOTE : Always clean the product after using it.
2. Repair or replace damaged parts and tighten loose screws, nuts or bolts as necessary or contact an authorised service centre for repair before using the product again.. Blade Maintenance When checking the blade,wait for a few moments after switching the product off, the blade will carry on moving. 1. Keep the hedging blade clean and free of debris. Remove trimmings. 2. Keep the hedging blade sharp to retain a good cutting performance.
available recycling and/ or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool and cover the battery pack connections with heavy duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components. TRANSPORT 1. Disconnect the product before transporting it anywhere.Always transport the product with the engine stopped.
TROUBLESHOOTING NOTE: Suspected malfunctions are often due to causes that the user can fix themselves. Therefore check the product using this section. In most cases the problem can be solved quickly.
