Half-size SBC HSB-910I HSB-910I Intel® Celeron® M Processor ISA Expansion Half-size SBC Two 200-pin DDRII 400 SODIMM 2 SATA I/ 1 IDE/ 1 FDD/ 1 CompactFlash 5 USB 2.0/ 4 COM/ 1 IrDA HSB-910 Manual Rev.A 1st Ed.
Half-size SBC HSB-910I Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Half-size SBC HSB-910I Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, and Celeron® M are trademarks of Intel® Corporation. ® Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
Half-size SBC HSB-910I Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 HSB-910I CPU Card • 1 Floppy Cable • 1 ATA100 Cable • 1 USB Cable • 1 Keyboard & Mouse Cable • 1 ATX Cable • 1 Serial + Parallel Cable • 1 Serial Cable • 2 SATA Cable • 1 Quick Installation Guide • 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or s
Half-size SBC HSB-910I Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specifications ............................................................ 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
Half-size SBC HSB-910I 2.18 Digital I/O (CN1) ...................................................... 2-12 2.19 LAN LED Connector (CN2, CN5)............................ 2-13 2.20 Internal Keyboard Connector (CN3)........................ 2-13 2.21 PS/2 Keyboard/ Mouse Connector (CN4)............... 2-13 2.22 Fan Connector (CN6) .............................................. 2-13 2.23 LVDS Channel Connector (CN7) ............................ 2-14 2.24 AC97 Connector (CN8) ....................................
Half-size SBC HSB-910I Chapter 1 General Information Chapter 1 General Information 1- 1
Half-size SBC HSB-910I 1.1 Introduction The HSB-910I utilizes the Intel® 910GMLE and ICH6M chipset, supporting Intel® Celeron® M 90nm processors with a FSB of 400MHz up to 1.8GHz. Offering two 200-pin DDR II SODIMM sockets, the HSB-910I supports two 200-pin DDRII 400 SODIMM system memory up to 2GB. This model offers a multitude of I/O including four COM ports and five USB2.0 ports.
Half-size SBC HSB-910I 1.2 Features Intel® Celeron® M 90nm Processor Up to 1.8GHz Intel® 910GMLE + Intel® ICH6M 200-pin DDRII 400 SODIMM x 2, Up to 2GB Gigabit Ethernet x 2 or x 1 (Optional) Integrated Intel® Enhance Graphics Core, VGA Support AC97 Codec Audio Daughter Board Optional Ultra ATA100 x 1, SATA I x 2, CompactFlash™ Type II x 1 USB2.
Half-size SBC HSB-910I 1.3 Specifications System CPU Intel® Celeron® M 90nm Processor up to 1.
Half-size SBC HSB-910I (Typical) EMC CE/FCC Class A Display VGA Chipset Enhanced Integrated Graphics Memory Shared memory up to 256M Resolutions Up to 2048 x 1536 @ 32bpp for CRT; 1920 x 1200 @ 18bpp for LCD I/O Storage SATA I x 2, IDE x 1, CompactFlash Type II x 1, Standard Floppy Disk Drive x 1 IrDA One IrDA Tx/Rx header Audio AC97 Codec Audio Daughter Board Optional Parallel Port Supports SPP/EPP/ECP mode USB USB2.
Half-size SBC HSB-910I Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
Half-size SBC HSB-910I 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Half-size SBC HSB-910I 2.
Half-size SBC 2.
Half-size SBC HSB-910I Solder Side Chapter 2 Quick Installation Guide 2 - 5
Half-size SBC HSB-910I 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Half-size SBC HSB-910I 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Half-size SBC HSB-910I DIMM1、2 DDRII Memory Slot CN1 Digital I/O CN2 LAN1 Active LED Connector CN3 PS/2 Keyboard/Mouse Connector CN4 Internal Keyboard Connector CN5 LAN2 Active LED Connector CN6 3-pin Fan Connector CN7 LVDS Channel Connector CN8 AC97 Connector Chapter 2 Quick Installation Guide 2 - 8
Half-size SBC HSB-910I 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Half-size SBC HSB-910I 2.7 Clear CMOS (JP1) JP1 Function 1-2 Protected (Default) 2-3 Clear 2.8 CF Voltage Selection (JP2) JP2 Function 1-2 +3.3V (Default) 2-3 +5V 2.9 LVDS Voltage Selection (JP4) JP4 Function 1-2 +5V 2-3 +3.3V (Default) 2.10 Front Panel Connector (FP1) Pin Signal Pin Signal 1 N.C. 2 Reset Switch (+) 3 N.C. 4 Reset Switch (-) 5 IDE LED (+) 6 Power LED (+) 7 IDE LED (-) 8 Power LED (-) 2.
Half-size SBC HSB-910I 2.12 Battery Connector (BT1) Pin Signal Pin Signal 1 VBAT(+) 2 GND(-) 2.13 RS-232 Serial Port Connector (COM1, COM3, COM4) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.14 RS-232/422/485 Serial Port Connector (COM2) Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422RXD+) 3 TXD (422TXD+/485DATA+) 4 DTR (422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.
Half-size SBC HSB-910I 2.16 LPT Port Connector (LPT1) Pin Signal Pin Signal 1 #STROBE 2 #AFD 3 DATA0 4 #ERROR 5 DATA1 6 #INIT 7 DATA2 8 #SLIN 9 DATA3 10 GND 11 DATA4 12 GND 13 DATA5 14 GND 15 DATA6 16 GND 17 DATA7 18 GND 19 #ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SELECT 26 N.C. Pin Signal 2.17 USB Connector (USB2~3) Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 USBD1+ 6 USBD2+ 7 GND 8 USBD2- 9 GND 10 +5V 2.
Half-size SBC 7 DIO1-7 HSB-910I 8 DIO1-8 2.19 LAN LED Connector (CN2, CN5) Pin Signal Pin Signal 1 Active_LED(-) 2 Active_LED(+) 2.20 Internal Keyboard Connector (CN3) Pin Signal 1 KB_CLK 2 KB_DATA 3 N.C. 4 GND 5 +5V 2.21 PS/2 Keyboard/ Mouse Connector (CN4) Pin Signal 1 KB_DATA 2 MS_DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK 2.
Half-size SBC HSB-910I 2.23 LVDS Channel Connector (CN7) Pin Signal Pin Signal 1 BKLEN 2 BKLCTL 3 PPVCC 4 GND 5 CH1_CLK# 6 CH1_CLK 7 PPVCC 8 GND 9 CH1_TX0# 10 CH1_TX0 11 CH1_TX1# 12 CH1_TX1 13 CH1_TX2# 14 CH1_TX2 15 N.C. 16 N.C. 17 I2C_DATA 18 I2C_CLK 19 CH2_TX0# 20 CH2_TX0 21 CH2_TX1# 22 CH2_TX1 23 CH2_TX2# 24 CH2_TX2 25 N.C. 26 N.C. 27 PPVCC 28 GND 29 CH2_CLK# 30 CH2_CLK 2.
Half-size SBC HSB-910I Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2 - 15
Half-size SBC HSB-910I Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
Half-size SBC 3.1 HSB-910I System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Half-size SBC 3.2 HSB-910I Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Half-size SBC HSB-910I PC Health Status This menu allows you to set the shutdown temperature for your system. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
Half-size SBC HSB-910I Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Half-size SBC HSB-910I The HSB-910I comes with a CD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install INF Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Please read following instructions for detailed installations.
Half-size SBC HSB-910I 4.1 Installation: Insert the HSB-910I CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 3 in order. Step 1 – Install INF Driver 1. Click on the Step 1-ICH6-M INF folder and then double click on the infinst_autol.exe 2. Follow the instructions that the window shows 3. The system will help you to install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2-VGA folder and then double click on the win2k_xp142550.exe 2.
Half-size SBC HSB-910I Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Half-size SBC HSB-910I A.1 Programming HSB-910I utilizes ITE 8712 chipset as its watchdog timer controller. ( K version ) Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
Half-size SBC HSB-910I (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
Half-size SBC Bit 7-2 1 0 HSB-910I Description Reserved Returns to the Wait for Key state. This bit is used when the configuration sequence is completed. Resets all logical devices and restores configuration registers to their power-on states.
Half-size SBC HSB-910I WatchDog Timer Time-out Value (LSB) Register (Index=73h, Default=00h) Bit 7-0 Description WDT Time-out value 7-0 WatchDog Timer Time-out Value (MSB) Register (Index=74h, Default=00h) Bit 7-0 Description WDT Time-out value 15-8 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .
Half-size SBC HSB-910I mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Half-size SBC HSB-910I MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Appendix A Programming the Watchdog Timer A-7
Half-size SBC HSB-910I Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near Appendix A Programming the Watchdog Timer A-8
Half-size SBC HSB-910I push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Half-size SBC END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Half-size SBC HSB-910I Appendix B I/O Information Appendix B I/O Information B-1
Half-size SBC B.
Half-size SBC HSB-910I B.
Half-size SBC B.3 IRQ Mapping Chart B.
Half-size SBC HSB-910I Appendix C Mating Connector Appendix C Mating Connector C - 1
Half-size SBC HSB-910I C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
Half-size SBC VGA1 IR1 CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 COM1 COM2 COM3 COM4 CRT Display Connector IrDA Connector Catch Electronics 3125-000-15S B N/A JIH VEI Electronics 21B12050-XX S10B-01G-4/2 .
