SubCompact Board GENE-HD05 GENE-HD05 ® AMD G-series T56N/T40E/T40R Processor Onboard DDR3 1066/1333 SODIMM 18/24-bit Single/Dual-channel LVDS LCD 8 USB 2.0, 4 COM, 2 SATA, 1 CFast 2 GbE, Mini Card GENE-HD05 Manual Rev. A 2nd Ed.
SubCompact Board GENE-HD05 Copyright Notice This document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-HD05 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMD® is trademark of Advanced Micro Devices. Microsoft Windows is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® All other product names or trademarks are properties of their respective owners.
SubCompact Board GENE-HD05 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: Product DVD GENE-HD05 If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
SubCompact Board GENE-HD05 Contents Chapter 1 General Information 1.1 Introduction................................................................... 1-2 1.2 Features ....................................................................... 1-3 1.3 Specifications ............................................................... 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ....................................................... 2-2 2.2 Location of Connectors and Jumpers ......................
SubCompact Board GENE-HD05 2.17 Touch Screen Connector (CN2)............................... 2-15 2.18 CPU FAN Connector (CN3) ..................................... 2-17 2.19 External +5VSB Input Connector (CN4) .................. 2-18 2.20 External +12V Input Connector (CN5) ..................... 2-18 2.21 Front Panel Connector (CN6) .................................. 2-18 2.22 Digital IO Port Connector (CN7)............................... 2-19 2.23 LPT Port Connector (CN8)................................
SubCompact Board GENE-HD05 2.42 USB Port 1 and 2 Connector (CN27) ....................... 2-34 2.43 HDMI Port Connector (CN28) .................................. 2-35 2.44 PS/2 Keyboard/Mouse Combo Port Connector (CN29) .......................................................................................... 2-36 2.45 VGA Port Connector (CN30).................................... 2-37 2.46 UIM Card Module Connector (CN32)....................... 2-38 2.47 DDR3 SODIMM Slot (SO-DIMM1) .......................
SubCompact Board GENE-HD05 Appendix C Mating Connector C.1 List of Mating Connectors and Cables......................C-2 Appendix D AHCI Setting D.1 Setting AHCI .............................................................D-2 Appendix E Electrical Specifications for I/O Ports E.1 Electrical Specifications for I/O Ports........................
SubCompact Board GENE-HD05 Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-HD05 1.1 Introduction AAEON announces a brand new 3.5” SubCompcat Board GENE-HD05, designed to fit in diverse applications that demand for fitting in different space limitations and high performance. GENE-HD05 accommodates T56N/T40E/T40R Processor onboard and AMD® features DDR3 G-series™ SODIMM 1066/1333 system memory up to 4GB. Moreover, GENE-HD05 adopts AMD® A50M chipset to achieve an excellent performance.
SubCompact Board GENE-HD05 1.2 Features Onboard AMD® G-series™ T56N/T40E/T40R Processor, Up to 1.65 GHz AMD® A50M DDR3 SODIMM 1066/1333 (T56N) Memory Up to 4 GB Gigabit Ethernet x 2 18/24-bit Dual/Single Channel LVDS LCD, CRT, HDMI 2CH AC97 2.3 Codec Audio CFast x 1, mSATA x 1 (Configured by BIOS), SATA x2 USB 2.
SubCompact Board GENE-HD05 1.3 Specifications System Form Factor 3.
SubCompact Board GENE-HD05 Gross Weight 0.88 lb (0.4 Kg) Operation Temperature 32°F ~ 140°F (0°C ~ 60°C) Storage Temperature -40°F ~ 176°F (-40°C ~ 80°C) Operation Humidity 0% ~ 90% relative humidity, non-condensing Display: Supports CRT/LVDS/HDMI simultaneous/ dual view displays Chipset AMD® G-series CPU integrated Resolutions Up to 2560 x 1600 T56N(18W) 1920 x 1200 T40E/T40R (6.5W/5.
SubCompact Board GENE-HD05 Chapter 2 Quick Installation Guide Chapter 2 Quick Installation Guide 2-1
SubCompact Board GENE-HD05 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-HD05 2.
SubCompact Board GENE-HD05 Solder Side Solder Side Chapter 2 Quick Installation Guide 2-4
SubCompact Board GENE-HD05 2.
SubCompact Board GENE-HD05 Solder Side Solder Side Chapter 2 Quick Installation Guide 2-6
SubCompact Board GENE-HD05 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
SubCompact Board GENE-HD05 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Label F unction 0B CN1 LPC Port CN2 Touch Screen Connector CN3 CPU FAN CN4 External +5VSB Input CN5 External +12V Input CN6 Front Panel Connector CN7 Digital IO Port CN8 LPT Port CN9 COM Port 2 CN10 COM Port 3 CN11 COM Port 4 CN12 USB 2.0 Ports 7 CN13 USB 2.
SubCompact Board GENE-HD05 CN21 +5V Output for SATA HDD CN22 LVDS Inverter / Backlight Connector CN23 LVDS Port CN24 COM Port 1 (D-SUB 9) CN25 Realtek LAN (RJ-45) Port 2 CN26 Realtek LAN (RJ-45) Port 1 CN27 USB Ports 1 and 2 CN28 HDMI Port CN29 PS/2 Keyboard/Mouse Combo Port CN30 VGA Port CN31 SPI Flash JTAG CN32 UIM Card Module SO-DIMM1 DDR3 SODIMM Slot CFDA1 CFast Slot PCIEA1 Mini-Card Slot Chapter 2 Quick Installation Guide 2-9
SubCompact Board GENE-HD05 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-HD05 2.7 Touch Screen 4/5/8-Wire Selection (JP1) 4/8-wire Mode JP1 5-wire Mode F unction 2B 1-2 4/8-wire (Default) 1-2 (open) 5-wire 2.8 AT/ATX Power Supply Mode Selection-1 (JP2) AT Mode JP2 ATX Mode F unction 3B 1-2 AT Mode (Default) 1-2 (open) ATX Mode 2.
SubCompact Board GENE-HD05 2.10 Clear CMOS Selection (JP4) 1 2 3 1 2 3 Normal (Default) Clear CMOS JP4 F unction 4B 1-2 Normal (Default) 2-3 Clear CMOS 2.11 LVDS Backlight Lightness Up/down Selection (JP5) 1 2 3 1 2 3 Backlight Up Backlight Down JP5 F unction 5B 1-2 Backlight Up 2-3 Backlight Down Note: Up/Down Selection is Push-Button type interface (do not use for Jumper Header) – and is only for PWM type Backlight Control (JP7 2~3). 2.
SubCompact Board GENE-HD05 2.13 LVDS Backlight Lightness Control Mode Selection (JP7) 1 2 3 1 2 3 VR Mode PWM Mode JP7 F unction 7B 1-2 VR Mode (Default) 2-3 PWM Mode 2.14 LVDS Backlight Inverter VCC Selection (JP8) 1 2 3 1 2 3 +12V +5V JP8 F unction 8B 1-2 +12V 2-3 +5V (Default) 2.
SubCompact Board GENE-HD05 2.16 LPC Port (CN1) LAD0 LAD1 LAD2 LAD3 +3.3V LFRAME# LRESET# GND LCLK LDRQ0 LDRQ1 SERIRQ 1 12 Pin Pin Name Signal Type Signal Level 1 LAD0 I/O +3.3V 2 LAD1 I/O +3.3V 3 LAD2 I/O +3.3V 4 LAD3 I/O +3.3V 5 +3.3V PWR +3.3V 6 LFRAME# IN 7 LRESET# OUT 8 GND GND 9 LCLK OUT 10 LDRQ0 IN 11 LDRQ1 IN 12 SERIRQ I/O Chapter 2 Quick Installation Guide 2-14 +3.3V +3.
SubCompact Board GENE-HD05 2.
SubCompact Board GENE-HD05 4 Wires 1 GND TOP BOTTOM LEFT RIGHT NC NC NC NC 9 Pin Pin Name Signal Type 1 GND GND 2 TOP IN 3 BOTTOM IN 4 LEFT IN 5 RIGHT IN 6 NC 7 NC 8 NC 9 NC 5 Wires GND UL(Y) UR(H) LL(L) LR(X) SENSE(S) NC NC NC 1 9 Chapter 2 Quick Installation Guide 2-16 Signal Level
SubCompact Board GENE-HD05 Pin Pin Name Signal Type 1 GND GND 2 UL(Y) IN 3 UR(H) IN 4 LL(L) IN 5 LR(X) IN 6 SENSE(S) IN 7 NC 8 NC 9 NC Signal Level Note: Touch mode can be set by JP1 2.
SubCompact Board GENE-HD05 2.19 External +5VSB Input Connector (CN4) 1 PS_ON# 2 GND 3 +5VSB Pin Pin Name Signal Type Signal Level 1 PS_ON# OUT +5V 2 GND GND 3 +5VSB PWR +5V 2.20 External +12V Input Connector (CN5) +12V GND Pin Pin Name Signal Type Signal Level 1 +12V PWR +12V 2 GND GND 2.
SubCompact Board Pin Pin Name 1 PWR_BTN- 2 PWR_BTN+ 3 HDD_LED- 4 HDD_LED+ 5 SPEAKER- 6 SPEAKER+ 7 PWR_LED- 8 PWR_LED+ 9 H/W RESET- 10 H/W RESET+ GENE-HD05 Signal Type Signal Level 2.22 Digital IO Port Connector (CN7) 1 3 5 7 9 2 4 6 8 10 Pin Pin Name Signal type Signal Level 1 DIO0 I/O +3.3V 2 DIO1 I/O +3.3V 3 DIO2 I/O +3.3V 4 DIO3 I/O +3.3V 5 DIO4 I/O +3.
SubCompact Board GENE-HD05 6 DIO5 I/O +3.3V 7 DIO6 I/O +3.3V 8 DIO7 I/O +3.3V 9 +3.3V PWR +3.3V 10 GND GND 2.23 LPT Port Connector (CN8) 1 2 AFD# ERROR# PRINT# SLIN# GND GND GND GND GND GND GND GND N.
SubCompact Board GENE-HD05 12 GND GND 13 PD5 I/O 14 GND GND 15 PD6 I/O 16 GND GND 17 PD7 I/O 18 GND GND 19 ACK# IN 20 GND GND 21 BUSY IN 22 GND GND 23 PE IN 24 GND GND 25 SLCT IN 26 NC 2.
SubCompact Board GENE-HD05 RS-232 Pin Pin Name Signal Type Signal Level 1 DCD IN 2 DSR IN 3 RX IN 4 RTS OUT ±9V 5 TX OUT ±9V 6 CTS IN 7 DTR OUT ±9V 8 RI/+5V/+12V IN/ PWR +5V/+12V 9 GND GND Pin Pin Name Signal Type Signal Level 1 RS422_TX- OUT ±5V 2 NC 3 RS422_RX+ 4 NC 5 RS422_TX+ 6 NC 7 RS422_RX- IN 8 NC/+5V/+12V PWR 9 GND GND RS-422 Chapter 2 Quick Installation Guide 2-22 IN OUT ±5V +5V/+12V
SubCompact Board GENE-HD05 RS-485 Pin Pin Name Signal Type Signal Level 1 RS485_D- I/O ±5V 2 NC 3 NC 4 NC 5 RS485_D+ I/O ±5V 6 NC 7 NC 8 NC/+5V/+12V PWR +5V/+12V 9 GND GND Note: COM2 RS-232/422/485 can be set by BIOS setting. Default is RS-232. Pin 8 function can be set by Jumper. 2.
SubCompact Board GENE-HD05 4 RTS OUT ±9V 5 TX OUT ±9V 6 CTS IN 7 DTR OUT 8 RI IN 9 GND GND ±9V 2.
SubCompact Board GENE-HD05 2.27 USB 2.0 Ports 7 Connector (CN12) Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USB7_D- DIFF 3 USB7_D+ DIFF 4 GND GND 5 GND GND 2.28 USB 2.
SubCompact Board GENE-HD05 2.29 USB 2.0 Ports 5 Connector (CN14) Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USB5_D- DIFF 3 USB5_D+ DIFF 4 GND GND 5 GND GND 2.30 USB 2.
SubCompact Board GENE-HD05 2.31 USB 2.0 Ports 3 Connector (CN16) Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USB3_D- DIFF 3 USB3_D+ DIFF 4 GND GND 5 GND GND 2.32 USB 2.
SubCompact Board GENE-HD05 2.33 Audio I/O Port Connector (CN18) MIC_L MIC_R GND_AUDIO LINE_L_IN LINE_R_IN GND_AUDIO LEFT_OUT GND_AUDIO RIGHT_OUT +5V_AUDIO 1 10 Pin Pin Name Signal Type 1 MIC_L IN 2 MIC_R IN 3 GND_AUDIO GND 4 LINE_L_IN IN 5 LINE_R_IN IN 6 GND_AUDIO GND 7 LEFT_OUT OUT 8 GND_AUDIO GND 9 RIGHT_OUT OUT 10 +5V_AUDIO PWR 2.
SubCompact Board GENE-HD05 Pin Pin Name Signal Type 1 GND GND 2 SATA_TX+ DIFF 3 SATA_TX- DIFF 4 GND GND 5 SATA_RX- DIFF 6 SATA_RX+ DIFF 7 GND GND Signal Level 2.
SubCompact Board GENE-HD05 2.36 +5V Output for SATA HDD Connector (CN21) +5V GND Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 GND GND 2.37 LVDS Inverter / Backlight Connector (CN22) 1 BLK_PWR 2 BKL_CONTROL 3 GND 4 GND 5 BKL_ENABLE Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT +5V Note: LVDS BKL_PWR can be set to +5V or +12V by JP8. LVDS BKL_CONTROL can be set by JP7.
SubCompact Board GENE-HD05 2.38 LVDS Port Connector (CN23) PIN 29 PIN 30 PIN 1 PIN 2 Pin Pin Name Signal Type 1 BKL_ENABLE OUT 2 BKL_CONTROL OUT 3 LCD_PWR PWR 4 GND GND 5 LVDS_A_CLK- DIFF 6 LVDS_A_CLK+ DIFF 7 LCD_PWR PWR 8 GND GND 9 LVDS_DA0- DIFF 10 LVDS_DA0+ DIFF 11 LVDS_DA1- DIFF 12 LVDS_DA1+ DIFF 13 LVDS_DA2- DIFF Signal Level +3.3V/+5V +3.
SubCompact Board GENE-HD05 14 LVDS_DA2+ DIFF 15 LVDS_DA3- DIFF 16 LVDS_DA3+ DIFF 17 DDC_DATA I/O +3.3V 18 DDC_CLK I/O +3.3V 19 LVDS_DB0- DIFF 20 LVDS_DB0+ DIFF 21 LVDS_DB1- DIFF 22 LVDS_DB1+ DIFF 23 LVDS_DB2- DIFF 24 LVDS_DB2+ DIFF 25 LVDS_DB3- DIFF 26 LVDS_DB3+ DIFF 27 LCD_PWR PWR 28 GND GND 29 LVDS_B_CLK- DIFF 30 LVDS_B_CLK+ DIFF +3.3V/+5V Note: LVDS LCD_PWR can be set to +3.3V or +5V by JP6. 2.
SubCompact Board GENE-HD05 Pin Pin Name Signal Type Signal Level 1 DCD IN 2 RX IN 3 TX OUT ±9V 4 DTR OUT ±9V 5 GND GND 6 DSR IN 7 RTS OUT 8 CTS IN 9 RI IN ±9V 2.
SubCompact Board GENE-HD05 7 MDI3+ DIFF 8 MDI3- DIFF 2.41 Realtek LAN (RJ-45) Port1 Connector (CN26) ACT/LINK LED 8 SPEED LED 1 Pin Pin Name Signal Type 1 MDI0+ DIFF 2 MDI0- DIFF 3 MDI1+ DIFF 4 MDI2+ DIFF 5 MDI2- DIFF 6 MDI1- DIFF 7 MDI3+ DIFF 8 MDI3- DIFF 2.
SubCompact Board GENE-HD05 Pin Pin Name Signal Type Signal Level 1 +5VSB PWR +5V 2 USB1_D- DIFF 3 USB1_D+ DIFF 4 GND GND 5 +5VSB PWR 6 USB2_D- DIFF 7 USB2_D+ DIFF 8 GND GND +5V 2.
SubCompact Board GENE-HD05 9 TMDS_ Data0- DIFF 10 TMDS_Clock+ DIFF 11 GND GND 12 TMDS_Clock- DIFF 13 CEC 14 NC 15 SCL I/O +3.3V 16 SDA I/O +3.3V 17 GND 18 +5V PWR +5V 19 HPLG_DETECT IN 2.
SubCompact Board GENE-HD05 2.
SubCompact Board GENE-HD05 2.46 UIM Card Module Connector (CN32) Pin Pin Name Signal Type 1 UIM_PWR PWR 2 UIM_RST IN 3 UIM_CLK IN 4 GND GND 5 UIM_VPP PWR 6 UIM_DATA I/O Signal Level 2.47 DDR3 SODIMM Slot (SO-DIMM1) Standard specification 2.
SubCompact Board GENE-HD05 PC1 NC PC2 GND PC3 NC PC4 NC PC5 NC PC6 NC PC7 GND PC8 NC PC9 NC PC10 NC PC11 NC PC12 NC PC13 +3.3V PWR +3.3V PC14 +3.3V PWR +3.3V PC15 GND GND PC16 GND GND PC17 NC GND GND 2.49 Mini-Card Slot (PCIEA1) Pin Pin Name Signal Type 1 PCIE_WAKE# IN 2 +3.3VSB PWR 3 NC 4 GND Signal Level +3.
SubCompact Board GENE-HD05 5 NC 6 +1.5V PWR 7 PCIE_CLK_REQ# IN 8 UIM_PWR PWR 9 GND GND 10 UIM_DATA I/O 11 PCIE_REF_CLK- DIFF 12 UIM_CLK IN 13 PCIE_REF_CLK+ DIFF 14 UIM_RST IN 15 GND GND 16 UIM_VPP PWR 17 NC 18 GND 19 NC 20 W_DISABLE# OUT 21 GND GND 22 PCIE_RST# OUT 23 PCIE_RX- DIFF 24 +3.3VSB PWR 25 PCIE_RX+ DIFF 26 GND GND 27 GND GND 28 +1.5V PWR Chapter 2 Quick Installation Guide 2-40 +1.5V GND +3.3V +3.3V +3.3V +1.
SubCompact Board GENE-HD05 29 GND GND 30 SMB_CLK I/O 31 PCIE_TX- DIFF 32 SMB_DATA I/O 33 PCIE_TX+ DIFF 34 GND GND 35 GND GND 36 USB_D- DIFF 37 GND GND 38 USB_D+ DIFF 39 +3.3VSB PWR 40 GND GND 41 +3.3VSB PWR 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.3VSB +3.3V +3.3V +3.3V +3.3V GND PWR +1.5V GND PWR +3.
SubCompact Board GENE-HD05 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求。 备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。 Chapter 2 Quick Installation Guide 2-42
SubCompact Board GENE-HD05 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
SubCompact Board 3.1 GENE-HD05 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
SubCompact Board 3.2 GENE-HD05 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
SubCompact Board GENE-HD05 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
SubCompact Board GENE-HD05 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings USB Configuration USB Configuration Parameters F81866 Super IO Configuration System Super IO Chip Parameters F81866 H/W Monitor Monitor hardware status Chapter 3 AMI BIOS Setup 3-5
SubCompact Board GENE-HD05 ACPI Settings Options summary: (default setting) ACPI Sleep State S3 (Suspend to RAM) Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
SubCompact Board GENE-HD05 CPU Configuration Chapter 3 AMI BIOS Setup 3-7
SubCompact Board GENE-HD05 SATA Configuration Options summary: (default setting) OnChip SATA Channel Disabled Enabled En/Disable Serial ATA OnChip SATA Type ACHI Legacy IDE Configure SATA controller operating as Legacy IDE/AHCI mode.
SubCompact Board GENE-HD05 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables Legacy USB Support. AUTO option disables legacy support if no USB devices are connected.
SubCompact Board GENE-HD05 If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
SubCompact Board GENE-HD05 F81866 Super IO Configuration Options summary: (default setting) Serial Port 1/2/3/4 Configuration Set Parameters of Serial Port 1/2/3/4 Parallel Port Configuration Set Parameters of Parallel Port Digital IO Port Configuration Set Input / Output of Digital IO Port Configuration Keep last state Power Failure Always on Always off Select AC power state when power is re-applied after a power failure.
SubCompact Board ERP Function Disabled Enabled ERP Function En/Disable Chapter 3 AMI BIOS Setup 3-12 GENE-HD05
SubCompact Board GENE-HD05 Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Select an optimal setting for Super IO device.
SubCompact Board Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Select an optimal setting for Super IO device.
SubCompact Board GENE-HD05 Serial Port 3 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3E8h; IRQ=11; IO=3E8h; IRQ=11; IO=2E8h; IRQ=11; Select an optimal setting for Super IO device.
SubCompact Board Serial Port 4 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2E8h; IRQ=11; IO=3E8h; IRQ=11; IO=2E8h; IRQ=11; Select an optimal setting for Super IO device.
SubCompact Board GENE-HD05 Parallel Port Configuration Options summary: (default setting) Parallel Port Disabled Enabled En/Disable specified parallel port. Change Settings Auto IO=378h; IRQ=5; IO=378h; IRQ=5,6,7,10,11,12; IO=278h; IRQ=5,6,7,10,11,12; IO=3BCh; IRQ=5,6,7,10,11,12; Select an optimal setting for Super IO device.
SubCompact Board Device Mode GENE-HD05 STD Printer Mode SPP Mode EPP-1.9 and SPP Mode EPP-1.7 and SPP Mode ECP Mode ECP and EPP 1.9 Mode ECP and EPP 1.
SubCompact Board GENE-HD05 Digital IO Port Configuration Options summary: (default setting) Port 1 Input Output Set GPIO as Input or Output. Port 2 Input Output Set GPIO as Input or Output. Port 3 Input Output Set GPIO as Input or Output. Port 4 Input Output Set GPIO as Input or Output.
SubCompact Board Port 5 Input Output Set GPIO as Input or Output. Port 6 Input Output Set GPIO as Input or Output. Port 7 Input Output Set GPIO as Input or Output. Port 8 Input Output Set GPIO as Input or Output.
SubCompact Board GENE-HD05 F81866 H/W Monitor Chapter 3 AMI BIOS Setup 3-21
SubCompact Board Setup submenu: Chipset Options summary: (default setting) North Bridge South Bridge Parameters South Bridge South Bridge Parameters Chapter 3 AMI BIOS Setup 3-22 GENE-HD05
SubCompact Board GENE-HD05 North Bridge Options summary: (default setting) Graphics Configuration Configure Graphics Settings.
SubCompact Board Graphics Configuration Options summary: (default setting) DP0 Output HDMI Disabled NB PCIE Connect Type (Display device) DP1 Output LVDS Disabled NB PCIE Connect Type (Display device) Chapter 3 AMI BIOS Setup 3-24 GENE-HD05
SubCompact Board GENE-HD05 South Bridge Options summary: (default setting) Power Mode ATX Type AT Type Select power supply mode. MiniCard & msata Minicard Configuration mSATA Support MiniCard & msata Device SB HD Azalia Configuration Options for SB HD Azalia.
SubCompact Board SB HD Azalia Configuration Options summary: (default setting) HD Audio Azalia Auto Device Disabled Enabled Enable Or Disable HD Audio Azalia Device Chapter 3 AMI BIOS Setup 3-26 GENE-HD05
SubCompact Board GENE-HD05 Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo. Launch RTL8111E PXE Disabled OpROM. Enabled En/Disable PXE boot for RTL8111E LAN Boot Option #x Set the system boot order.
SubCompact Board GENE-HD05 Setup submenu: Security Options summary: (default setting) Administrator Not set Password/ User Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
SubCompact Board GENE-HD05 Setup submenu: Save & Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
SubCompact Board GENE-HD05 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
SubCompact Board GENE-HD05 The GENE-HD05 comes with a DVD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install LAN Driver Step 3 – Install Audio Driver Step 4 – Install AHCI Driver Step 5 – Install Touch Driver Step 6 – Install TPM Driver Please read instructions below for further detailed installations.
SubCompact Board GENE-HD05 4.1 Installation: Insert the GENE-HD05 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install LAN Driver 1.
SubCompact Board GENE-HD05 Step 4 – Install AHCI Driver Please refer to the Appendix D AHCI Setting Step 5 – Install Touch Driver 1. Click on the STEP5-TOUCH folder and double click on the Setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 6 – Install TPM Driver 1. Click on the STEP6-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe file located in each OS folder 3.
SubCompact Board GENE-HD05 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
SubCompact Board GENE-HD05 A.1 Programming GENE-HD05 utilizes FINTEK 81866 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the FINTEK 81866 enters the normal mode with all logical devices disabled except KBC.
SubCompact Board GENE-HD05 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
SubCompact Board GENE-HD05 Watch Dog Timer 1, 2, 3 Control Register (Index=F5h,F6h,FAh Default=00h) Appendix A Programming the Watchdog Timer A-4
SubCompact Board GENE-HD05 A.
SubCompact Board GENE-HD05 Void aaeonWdtSetTimeoutCount(BYTE tTimeout){ f81866SetLdn(0x07); f81866WriteByte(F81866_WDT_TIME_REG, tTimeout); } Void aaeonWdtSetEnable(BOOL bEnable){ f81866SetLdn(0x07); if(bEnable){ f81866WriteByte(0x30, 0x01); WDT_BASE_ADDR = (f81866ReadByte(F81866_WDT_BASEADDR_REG_MSB) << 8) | f81866ReadByte(F81866_WDT_BASEADDR_REG_LSB); WDT_STATUS = f81866ReadByte(F81866_WDT_CONTROL_REG); f81866WriteByte(F81866_WDT_CONTROL_REG, WDT_STATUS | 0x20); WDT_STATUS = f81866ReadByte(F81866_WDT_P
SubCompact Board GENE-HD05 Void aaeonSuperIOClose(){ aaeonioWritePortByte(F81866_INDEX, 0xaa); } Appendix A Programming the Watchdog Timer A-7
SubCompact Board GENE-HD05 Appendix B I/O Information Appendix B I/O Information B-1
SubCompact Board B.
SubCompact Board GENE-HD05 Appendix B I/O Information B-3
SubCompact Board B.
SubCompact Board GENE-HD05 B.3 IRQ Mapping Chart B.
SubCompact Board GENE-HD05 Appendix C Mating Connector Appendix C Mating Connector C - 1
SubCompact Board GENE-HD05 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables.
SubCompact Board GENE-HD05 CN15 USB Port Connector Molex 51021-0500 CN16 USB Port Connector Molex 51021-0500 CN17 USB Port Connector Molex 51021-0500 CN18 Audio Connector Molex 51021-1000 CN21 +5Vout Connector JST PHR-2 CN22 CN23 LVDS Inverter JST Connector LVDS HIROSE Connector CN29 P/S2 KB/MS Connector BATA1 External RTC Molex Connector JST PHR-5 USB Wafer Cable USB Wafer Cable USB Wafer Cable Audio Cable 2 Pins For HDD Power N/A DF13-30DS-1.
SubCompact Board GENE-HD05 Appendix D AHCI Setting Appendix D AHCI Setting D-1
SubCompact Board GENE-HD05 D.1 Setting AHCI OS installation to setup AHCI Mode. Step 1: Copy the files below from “Driver DVD -> STEP4 AHCI\WinXP\SB8xx_RAID_XP_3.2.1540.
SubCompact Board GENE-HD05 Step 3: BIOS Setup menu select “Advanced\OnChip SATA Type -> AHCI” Step 4: Setup OS Appendix D AHCI Setting D-3
SubCompact Board Step 5: Press “F6” Step 6: Choose “S” Appendix D AHCI Setting D-4 GENE-HD05
SubCompact Board GENE-HD05 Step 7: Choose “AMD® A50M” Step 8: It will show the model number you select and then press “ENTER” Step 9: Setup is loading files Appendix D AHCI Setting D-5
SubCompact Board GENE-HD05 Appendix D AHCI Setting Appendix D AHCI Setting D-1
SubCompact Board GENE-HD05 D.1 Setting AHCI OS installation to setup AHCI Mode. Step 1: Copy the files below from “Driver DVD -> STEP4 AHCI\WinXP\SB8xx_RAID_XP_3.2.1540.
SubCompact Board GENE-HD05 Step 3: BIOS Setup menu select “Advanced\OnChip SATA Type -> AHCI” Step 4: Setup OS Appendix D AHCI Setting D-3
SubCompact Board Step 5: Press “F6” Step 6: Choose “S” Appendix D AHCI Setting D-4 GENE-HD05
SubCompact Board GENE-HD05 Step 7: Choose “AMD® A50M” Step 8: It will show the model number you select and then press “ENTER” Step 9: Setup is loading files Appendix D AHCI Setting D-5
SubCompact Board GENE-HD05 Appendix E Electrical Specifications for I/O Ports Appendix E Electrical Specifications for I/O Ports E-1
SubCompact Board GENE-HD05 E.1 Electrical Specifications for I/O Ports I/O Reference Signal Name Rate Output LVDS Inverter / Backlight Connector CN22 VDD +5V/2A or +12V/2A LPC Port CN1 +3.3VCC +3.3V/0.5A CPU FAN CN3 VDD +12V/0.5A Digital IO Port CN7 D0~D7 COM Port 2 CN9 +5V/+12V USB 2.0 Ports 7 CN12 +5V USB 2.0 Ports 8 CN13 +5V USB 2.0 Ports 5 CN14 +5V USB 2.0 Ports 6 CN15 +5V USB 2.0 Ports 3 CN16 +5V USB 2.
SubCompact Board Mini-Card Slot PCIEA1 GENE-HD05 +3.3VSB +1.5V +3.3V/1.1A +1.5V/0.
