Installation guide

ManualsBrandsAaeon ManualsComputer equipmentEMB-945T

Mini-ITX EMB-945T Rev.A

EMB-945T Rev.A

Intel

Core™ 2 Duo/ Core™ Duo/

Celeron

M Processor,

Up to 2.16 GHz

Mini-ITX

Marvell

Ethernet

AC 97 Audio & Mini PCI

EMB-945T Manual Rev.A 5th Ed.

July 2010

Summary of content (60 pages)

PAGE 1
Mini-ITX EMB-945T Rev.A EMB-945T Rev.A ® Intel Core™ 2 Duo/ Core™ Duo/ Celeron® M Processor, Up to 2.16 GHz Mini-ITX Marvell ® Ethernet AC 97 Audio & Mini PCI EMB-945T Manual Rev.A 5th Ed.
PAGE 2
Mini-ITX EMB-945T Rev.A Copyright Notice This document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PAGE 3
Mini-ITX EMB-945T Rev.A Acknowledgments All other products’ name or trademarks are properties of their respective owners. z Award is a trademark of Award Software International, Inc. z CompactFlash™ is a trademark of the Compact Flash Association. z Intel®, Core™ 2 Duo, Core™ Duo, and Celeron® M are trademarks of Intel® Corporation. z Microsoft Windows® is a registered trademark of Microsoft Corp. z ITE is a trademark of Integrated Technology Express, Inc.
PAGE 4
Mini-ITX EMB-945T Rev.A Packing List Before you begin installing your card, please make sure that the following materials have been shipped: z 1 1701440050 44-pin ATA33 Cable z 1 1700200200 DVI Cable z 2 1709100201 USB Cable z 4 1701100206 Serial Port Cable z 1 1700080180 TV-out Cable z 1 1709070500 Serial ATA Cable z 1 1702150150 Serial ATA Power Cable z 1 9657666600 Jumper Cap z 1 M20852T000 Rear I/O Bracket z 1 M166666006 CPU Fan, box 60 x 25.
PAGE 5
Mini-ITX EMB-945T Rev.A Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................. 2-2 2.2 Location of Connectors and Jumpers ...................... 2-3 2.
PAGE 6
Mini-ITX EMB-945T Rev.A 2.18 Audio 5.1 Channel / SPDIF Connector (CN6) ..... 2-13 2.19 Internal Mouse Connector (CN7) .......................... 2-14 2.20 LCD Inverter Connector (CN8) ............................ 2-14 2.21 PCI Express Slot For AAEON (CN9) .................... 2-14 2.22 LVDS (2)-LCD Connector (CN10)......................... 2-15 2.23 DVI Connector (CN11) ........................................ 2-15 2.24 LVDS (1)-LCD Connector (CN12)......................... 2-16 2.
PAGE 7
Mini-ITX Appendix A EMB-945T Rev.A Programming The Watchdog Timer A.1 Programming ...........................................................A-2 A.2 ITE 8712 Watchdog Timer Initial Program ..............A-6 Appendix B I/O Information B.1 I/O Address Map......................................................B-2 B.2 Memory Address Map..............................................B-3 B.3 IRQ Mapping Chart..................................................B-3 B.4 DMA Channel Assignments.
PAGE 8
Mini-ITX EMB-945T Rev.
PAGE 9
Mini-ITX EMB-945T Rev.A 1.1 Introduction The EMB-945T Rev.A adopts the latest Intel® Core™ Duo processor and Mobile Intel® 945GME+ICH7M chipset for better power-management capabilities and enhanced performance. EMB-945T Rev.
PAGE 10
Mini-ITX EMB-945T Rev.A 1.2 Features z Socket-478M Intel® Core™ 2 Duo/ Core™ Duo/ Celeron® M Processor z Intel® 945GME + ICH7M z SODIMM DDR2 400/533/667 Max. 4 GB z Gigabit Ethernet x 1 (Marvell® 88E8053) z Up To 24-bit Dual-channel LVDS LCD z AC97 5.1CH Audio z Type II CompactFlash™ x 1, SATA x 2, EIDE x 1 z COM x 6, Parallel x 1, USB2.
PAGE 11
Mini-ITX EMB-945T Rev.A 1.3 Specifications System z Processor Supports Socket 478M Intel® Core™ 2 Duo/ Core™ Duo/ Celeron® M Processors up to 2.16 GHz , FSB 533/667 z System Memory 200-pin DDR2 SODIMM Socket x 2, Max.
PAGE 12
Mini-ITX EMB-945T Rev.A z Operating 32˚F~ 140˚F (0˚C ~ 60˚C) Temperature z Storage -40˚F~ 176˚F (-40˚C ~ 80˚C) Temperature z Operating Humidity 0%~90% relative humidity, non-condensing z MTBF (Hours) 70,000 Display: Supports CRT/LCD, CRT/TV, CRT/DVI, LCD/DVI and LCD/TV simultaneous/ dual view displays z Chipset Intel®945GNE z VGA/LCD Controller 1. Intel® 945GME integrated VGA, Shared memory up to 224MB with DVMT , LCD supports up to 24-bit dual-channel LVDS 2.
PAGE 13
Mini-ITX EMB-945T Rev.A z USB USB2.
PAGE 14
Mini ITX EMB-945T Rev.A Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No.
PAGE 15
Mini ITX EMB-945T Rev.A 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
PAGE 16
Mini ITX EMB-945T Rev.A 2.
PAGE 17
Mini ITX EMB-945T Rev.
PAGE 18
Mini ITX EMB-945T Rev.A 2.
PAGE 19
Mini ITX Solder Side Chapter 2 Quick Installation Guide 2 - 6 EMB-945T Rev.
PAGE 20
Mini ITX EMB-945T Rev.A 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
PAGE 21
Mini ITX EMB-945T Rev.A 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each of the board's connectors: Connectors Label Function CN1 CD-IN Connector CN2 Digital I/O Connector CN3 TV-Out Connector CN4 Internal Keyboard Connector CN5 Fan2 Connector CN6 Audio 5.
PAGE 22
Mini ITX EMB-945T Rev.
PAGE 23
Mini ITX EMB-945T Rev.A 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
PAGE 24
Mini ITX EMB-945T Rev.A 2.7 LVDS(1)-LCD(CN12) Voltage Selection (JP1) JP1 Function 1-2 +5V 2-3 +3.3V (Default) 2.8 LVDS (2)-LCD(CN10) Voltage Selection (JP2) JP2 Function 1-2 +5V 2-3 +3.3V (Default) 2.9 COM2 Ring/+5V/+12V Selection (JP3) JP3 Function 1-2 +12V 3-4 +5V 5-6 Ring (Default) 2.10 LCD INVERTER Voltage Selection (JP4) JP4 Function 1-2 +5V (Default) 2-3 +12V 2.11 Audio Out Selection (JP5) JP5 Function 1-3, 2-4 W/ Amplifier 3-5, 4-6 W/O Amplifier (Default) 2.
PAGE 25
Mini ITX EMB-945T Rev.A 2.13 CD-IN Connector (CN1) Pin Signal 1 CD_IN_L 2 CD_GND 3 CD_GND 4 CD_IN_R 2.14 Digital I/O Connector (CN2) This connector offers 4-pair of digital I/O functions and address is set in BIOS. The default address is 2A1H.
PAGE 26
Mini ITX EMB-945T Rev.A 2.15 TV_Out Connector (CN3) Pin Signal Pin Signal 1 Y 2 CVBS 3 GND 4 GND 5 C 6 N.C. 7 GND 8 N.C. 2.16 Internal Keyboard Connector (CN4) Pin Signal 1 KB_CLK 2 KB_DATA 3 N.C. 4 GND 5 +5V 2.17 Fan2 Connector (CN5) Pin Signal 1 GND 2 +12V 3 Speed Sense 4 Speed Control 2.18 Audio 5.
PAGE 27
Mini ITX EMB-945T Rev.A 11 CNE-OUT 12 GND 13 SPDIF-OUT 14 SPDIF-IN 2.19 Internal Mouse Connector (CN7) Pin Signal 1 MS_CLK 2 MS_DATA 3 GND 4 +5V 2.20 LCD Inverter Connector (CN8) Pin Signal 1 +5V/+12V 2 +5V/+12V 3 ENBKL 4 Adjust backlight 5 GND 6 GND 2.21 PCI Express Slot For AAEON (CN9) Pin Signal Pin Signal 1 GND 2 +3.3V 3 PCIE_RXP1 4 +3.3V 5 PCIE_RXN1 6 PCIE_WAKE# 7 GND 8 PCIE_RESET# 9 PCIE1_CLKP 10 +3.3VSB 11 PCIE1_CLKN 12 +3.
PAGE 28
Mini ITX EMB-945T Rev.A 19 +12V 20 PCIE2_CLKP 21 +12V 22 PCIE2_CLKN 23 SMBDAT 24 GND 25 SMBCLK 26 PCIE_RXP2 27 +3.3V 28 PCIE_RXN2 29 +3.3V 30 GND 2.22 LVDS(2)-LCD Connector (CN10) Pin Signal Pin Signal 1 ENBKL 2 N.
PAGE 29
Mini ITX EMB-945T Rev.A 5 DVI_TXCLK+ 6 DVI_TXCLK- 7 GND 8 +5V 9 HotPlug_Detect 10 +5V 11 DVI_TX2+ 12 DVI_TX2- 13 GND 14 GND 15 DVI_TX0+ 16 DVI_TX0- 17 N.C. 18 N.C. 19 I2C_DATA 20 I2C_CLK 2.24 LVDS(1)-LCD Connector (CN12) Pin Signal Pin Signal 1 ENBKL 2 N.
PAGE 30
Mini ITX EMB-945T Rev.A 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.26 COM3 RS-232 Serial Port Connector (CN14) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.27 Fan1 Connector (CN15) Pin Signal 1 GND 2 +12V 3 Speed Sense 4 Speed Control 2.28 COM5 RS-232 Serial Port Connector (CN16) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C.
PAGE 31
Mini ITX EMB-945T Rev.A 2.29 COM4 RS-232 Serial Port Connector (CN17) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N.C. 2.30 IrDA Connector (CN18) Pin Signal 1 +5V 2 N.C. 3 IRRX 4 GND 5 IRTX 6 N.C. 2.31 ATX Power Connector (CN19) Pin Signal Pin Signal 1 2 +3.3V 11 +3.3V +3.
PAGE 32
Mini ITX EMB-945T Rev.A 2.32 USB Connector (CN20) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 7 9 USBD1+ GND GND 6 8 10 USBD2+ USBD2+5V 2.33 USB Connector (CN21) Pin Signal Pin Signal 1 +5V 2 GND 3 USBD1- 4 GND 5 7 9 USBD1+ GND GND 6 8 10 USBD2+ USBD2+5V 2.
PAGE 33
Mini ITX EMB-945T Rev.A 23 IO WRITE 24 GND 25 IO READ 26 GND 27 IO READY 28 GND 29 DACK 30 GND 31 IRQ14 32 N.C. 33 ADDR1 34 UDMA DETECT 35 ADDR0 36 ADDR2 37 CS#1 38 CS#3 39 LED 40 GND 41 +5V 42 +5V 43 GND 44 N.C. 2.
PAGE 34
Mini ITX EMB-945T Rev.
PAGE 35
Mini-ITX EMB-945T Rev.
PAGE 36
Mini-ITX 3.1 EMB-945T Rev.A System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
PAGE 37
Mini-ITX 3.2 EMB-945T Rev.A Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press ~~immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.~~
PAGE 38
Mini-ITX EMB-945T Rev.A Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum. Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations.
PAGE 39
Mini-ITX EMB-945T Rev.
PAGE 40
Mini-ITX EMB-945T Rev.A The EMB-945T Rev.A comes with a AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
PAGE 41
Mini-ITX EMB-945T Rev.A 4.1 Installation: Insert the EMB-945T Rev.A CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Chip Driver 1. Click on the Step 1-Chip folder and then double click on the Setupl.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install VGA Driver 1. Click on the Step 2-vga folder and select the OS folder your system is 2. Double click on the .
PAGE 42
Mini-ITX EMB-945T Rev.A Step 4 – Install Audio Driver 1. Click on the Step 4- AC97 folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4.
PAGE 43
Mini-ITX EMB-945T Rev.
PAGE 44
Mini-ITX EMB-945T Rev.A A.1 Programming EMB-945T Rev.A utilizes ITE 8712 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
PAGE 45
Mini-ITX EMB-945T Rev.A There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
PAGE 46
Mini-ITX EMB-945T Rev.A WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
PAGE 47
Mini-ITX EMB-945T Rev.
PAGE 48
Mini-ITX EMB-945T Rev.A A.2 IT8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
PAGE 49
Mini-ITX EMB-945T Rev.
PAGE 50
Mini-ITX EMB-945T Rev.
PAGE 51
Mini-ITX EMB-945T Rev.A MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
PAGE 52
Mini-ITX EMB-945T Rev.A push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
PAGE 53
Mini-ITX EMB-945T Rev.
PAGE 54
Mini-ITX B.1 I/O Address Map Appendix B I/O Information B-2 EMB-945T Rev.
PAGE 55
Mini-ITX EMB-945T Rev.A B.2 Memory Address Map B.
PAGE 56
Mini-ITX B.4 DMA Channel Assignments Appendix B I/O Information B-4 EMB-945T Rev.
PAGE 57
Mini-ITX EMB-945T Rev.
PAGE 58
Mini-ITX EMB-945T Rev.A C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Label Function Mating Connector CN1 CD-IN Vendor HOBASE CN2 Digital I/O Catch CN3 TV-Out Catch CN4 Internal Keyboard HOBASE CN5 Fan Catch CN6 Audio 5.1 Channel/ SPDIF Catch CN7 Internal Mouse HOBASE CN8 LCD Inverter HOBASE CN10 LVDS LCD ComWeal Appendix C Mating Connector C - 2 Model no 2.54mm Pitch 4 pins (HO-BASE 2541-1H-4 or compatible) 2.
PAGE 59
Mini-ITX EMB-945T Rev.A 103-303M or compatible) CN11 DVI Catch CN12 LVDS LCD ComWeal CN13 RS-232 Serial Port Catch CN14 RS-232 Serial Port Catch CN15 Fan Catch CN16 RS-232 Serial Port Catch CN17 RS-232 Serial Port Catch CN18 IrDA HOBASE CN19 ATX Power Socket Catch CN20 USB Port Catch 2.00mm Pitch 8 pins ( Catch H754-2x10 or compatible) 1.25mm Pitch 30 Pins(ComWeal 103-303M or compatible) 2.00mm Pitch 10 pins ( Catch H754-2x5 or compatible) 2.
PAGE 60
Mini-ITX CN21 USB Port Catch CN22 EIDE Connector Catch CN23 Front Pannel HOBASE Appendix C Mating Connector C - 4 EMB-945T Rev.A compatible) 2.00mm Pitch 10 pins ( Catch H754-2x5 or compatible) 2.00mm Pitch 44 pins ( Catch H820-2 or compatible) 2.