Touch Panel PC AHP-2173 AHP-2173 ® Onboard Intel Atom™ D2550 1.86 GHz Processor Touch Panel PC With 17” TFT LCD st AHP-2173 Manual 1 Ed.
Touch Panel PC AHP-2173 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Touch Panel PC AHP-2173 Acknowledgments All other products’ name or trademarks are properties of their respective owners. AMI is a trademark of American Megatrends Inc. Intel , and Atom™ are trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation. ® ® ® All other product names or trademarks are properties of their respective owners.
Touch Panel PC AHP-2173 Packing List Before you begin operating your PC, please make sure that the following materials are enclosed: AHP-2173 Touch Panel PC Mounting brackets and screws DVD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Touch Panel PC AHP-2173 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a firm surface during installation.
Touch Panel PC AHP-2173 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). IT MAY DAMAGE THE EQUIPMENT. FCC This device complies with Part 15 FCC Rules.
Touch Panel PC AHP-2173 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 六价铬 多溴联苯 多溴二苯醚 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O:表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ
Touch Panel PC AHP-2173 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 Dimension ................................................................. 1-7 Chapter 2 Hardware Installation 2.1 Panelmount Installation .............................................
Touch Panel PC AHP-2173 B.4 DMA Channel Assignments ...................................B-5 Appendix C AHCI Setting C.1 Setting AHCI .........................................................
Touch Panel PC AHP-2173 Chapter 1 General Information Chapter 1 General Information 1- 1
Touch Panel PC AHP-2173 1.1 Introduction ® The AHP-2173 operator panel is an Intel Atom™ D2550 1.86 GHz processor computer that is designed to serve as a human machine interface (HMI). It is a PC-based system with 17" color TFT LCD display, onboard Ethernet controller, multi-COM port interfaces and an audio controller. With a built-in CFast™ socket, the AHP-2173 is as compact and user friendly as a multi-function computer.
Touch Panel PC AHP-2173 1.2 Features 17” SXGA TFT LED LCD Onboard Intel Atom D2550 1.
Touch Panel PC AHP-2173 1.3 Specification System CPU ® Onboard Intel Atom™ D2550 1.86 GHz Processor System Memory DDR3 SODIMM x 1, Max. 4 GB (Default is 2 GB) Ethernet 10/100/1000Base-TX, RJ-45 x 2 LCD / CRT Controller Integrated in Processor I/O Port USB2.0 x 2 RS-232 x 2 RS-232/422/485 x 1 LAN x 2 VGA x 1 Line-out x 1 Power switch x 1 Storage Disk Drive 2.
Touch Panel PC Dimension AHP-2173 16.56”(W) x 14.08”(H) x 2.87”(D) (420mm x 358mm x 73mm) Carton Dimension 26.02”(W) x 19.53”(H) x 8.11”(D) (661mm x 496mm x 206mm) Net Weight 13.2 lb (6 kg) Gross Weight 18.7 lb (8.
Touch Panel PC AHP-2173 Reverse protection LCD Display Type 17”, SXGA TFT LCD Max. Resolution 1280x1024 Max. Colors 16.
Touch Panel PC AHP-2173 1.
Touch Panel PC AHP-2173 Chapter 2 Hardware Installation Chapter 2 Quick Installation Guide 2-1
Touch Panel PC AHP-2173 2.1 Panelmount Installation The display panel can be mounted into the wall. You will need the screws along with the mounting brackets, which be packed in the accessory box. Follow the steps below: Before you start to follow the instructions, please place the display panel into the wall. See the following illustration on the left. Step 1: Place the mounting brackets and plug the screw. Step 2: Aim the mounting set at the hole on the monitor.
Touch Panel PC 1 2 AHP-2173 3 4 Complete Illustration Chapter 2 Quick Installation Guide 2 - 3
Touch Panel PC AHP-2173 2.
Touch Panel PC AHP-2173 2.
Touch Panel PC Step 3: Fasten the Hard Disk onto the bracket Chapter 2 Quick Installation Guide 2 - 6 AHP-2173
Touch Panel PC AHP-2173 Step 4: Fasten the screws of the hard disk bracket onto the AHP-2173 Chapter 2 Quick Installation Guide 2 - 7
Touch Panel PC AHP-2173 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Touch Panel PC 3.1 AHP-2173 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Touch Panel PC 3.2 AHP-2173 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Touch Panel PC AHP-2173 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Touch Panel PC AHP-2173 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings USB Configuration USB Configuration Parameters Chapter 3 AMI BIOS Setup 3-5
Touch Panel PC Super IO Configuration System Super IO Chip Parameters H/W Monitor Monitor hardware status Chapter 3 AMI BIOS Setup 3-6 AHP-2173
Touch Panel PC AHP-2173 ACPI Settings Options summary: (default setting) Suspend Disabled S1 only(CPU Stop ACPI Sleep State Clock) S3 only(Suspend to RAM) Select the ACPI state used for System Suspend Wake on Ring Enabled Disabled Enabled or disabled wake on ring function.
Touch Panel PC AHP-2173 RTC Wake Settings Enable system to wake from S5 using RTC alarm. RTC Wake Settings Options summary: (default setting) Wake system with Disabled Fixed Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
Touch Panel PC Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled AHP-2173 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
Touch Panel PC CPU Configuration Options summary: (default setting) Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Chapter 3 AMI BIOS Setup 3-10 AHP-2173
Touch Panel PC AHP-2173 SATA Configuration Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI Configure SATA controller operating as IDE/AHCI mode. SATA Port 0/Port 1 Disabled Enabled En/Disable the selected port.
Touch Panel PC SATA Port 0/Port 1 Hot Disabled Plug Enabled AHP-2173 En/Disable Hot Plug feature for specified port.
Touch Panel PC AHP-2173 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected.
Touch Panel PC AHP-2173 Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Touch Panel PC AHP-2173 Super IO Configuration Options summary: (default setting) Serial Port 1/2/3 Configuration Set Parameters of Serial Port 1/2/3 Restore AC Power Loss Power Off Power On Last State Select AC power state when power is re-applied after a power failure.
Touch Panel PC AHP-2173 Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Touch Panel PC AHP-2173 IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device.
Touch Panel PC Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Touch Panel PC AHP-2173 IO=3E8h; IRQ=3,4,5,7,10,11,12; IO=2E8h; IRQ=3,4,5,7,10,11,12; Select a resource setting for Super IO device. COM2 Type Select RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
Touch Panel PC AHP-2173 Serial Port 3 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Touch Panel PC AHP-2173 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; Select a resource setting for Super IO device.
Touch Panel PC H/W Monitor Chapter 3 AMI BIOS Setup 3-22 AHP-2173
Touch Panel PC AHP-2173 Setup submenu: Chipset Options summary: (default setting) Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters Chapter 3 AMI BIOS Setup 3-23
Touch Panel PC Host Bridge Options summary: (default setting) Intel IGD Configuration Config Intel IGD Settings.
Touch Panel PC AHP-2173 Intel IGD Configuration Options summary: (default setting) Auto Disable IGD Enabled Disabled Audo disable IGD upon external GFX detected IGFX - Boot Type VBIOS Default CRT LVDS Select Primary boot display device LVDS Backlight 100% Controller 75% Chapter 3 AMI BIOS Setup 3-25
Touch Panel PC 50% 25% 0% Adjust backlight brightness.
Touch Panel PC AHP-2173 South Bridge Options summary: (default setting) Power Mode ATX Type AT Type Select the power type used on the system TPT Devices HD audio and onboard LAN Settings. PCI Express Root Port PCIe root port Settings.
Touch Panel PC AHP-2173 TPT Devices Options summary: (default setting) Azalia Controller Disabled HD Audio Enable or disabled Azalia controller R8111E #1 Controller Disabled Enabled Enable or disable PCIE Lan. R8111E #2 Controller Disabled Enabled Enable or disable PCIE Lan.
Touch Panel PC AHP-2173 PCI Express Root Port 0/1/2/3 Options summary: (default setting) PCI Express Root Disabled Port 0/1/2/3 Enabled Control the PCI Express Root Port.
Touch Panel PC Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo.
Touch Panel PC AHP-2173 The order of boot priorities.
Touch Panel PC Setup submenu: Security Options summary: (default setting) Administrator Not set Password/ User Password Chapter 3 AMI BIOS Setup 3-32 AHP-2173
Touch Panel PC AHP-2173 You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. A second dialog box asks you to retype the password for confirmation.
Touch Panel PC AHP-2173 Setup submenu: Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Touch Panel PC AHP-2173 Save the changes done so far as User Defaults Restore User Defaults Restore the User Defaults to all the setup options Chapter 3 AMI BIOS Setup 3-35
Touch Panel PC AHP-2173 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Touch Panel PC AHP-2173 The AHP-2173 comes with a DVD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install Audio Driver Step 5 – Install AHCI Driver (Optional) Step 6 – Install TPM Driver Step 7 – Install Touch Panel Driver Step 8 – Install Serial Port Driver (Optional) Please read instructions below for further detailed installations.
Touch Panel PC AHP-2173 4.1 Installation: Insert the AHP-2173 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 8 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver ® For Windows 7 1.
Touch Panel PC AHP-2173 automatically 2. Install IEMGD Double click on the IEMGDInstall.
Touch Panel PC AHP-2173 If you want to update driver, please uninstall driver first. Uninstall IEMGD 1. Double click on the IEMGDInstall.exe 2. Follow the instructions that the window shows 3.
Touch Panel PC AHP-2173 Step 3 – Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is 2. Double click on the setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 4 – Install Audio Driver 1. Click on the STEP4-AUDIO folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4.
Touch Panel PC AHP-2173 Step 6 – Install TPM Driver 1. Click on the STEP6-TPM folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 7 – Install Touch Panel Driver 1. Click on the STEP7-TOUCH folder and select the OS folder your system is 2. Double click on the setup.exe located in each OS folder 3.
Touch Panel PC AHP-2173 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Touch Panel PC AHP-2173 A.1 Programming AHP-2173 utilizes ITE 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON initial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8783 enters the normal mode with all logical devices disabled except KBC.
Touch Panel PC AHP-2173 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Touch Panel PC AHP-2173 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
Touch Panel PC AHP-2173 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5
Touch Panel PC AHP-2173 A.2 ITE8783 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
Touch Panel PC AHP-2173 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h Appendix A Programming the Watchdog Timer A-7
Touch Panel PC CALL Write_Configuration_Data RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] Appendix A Programming the Watchdog Timer A-8 AHP-2173
Touch Panel PC AHP-2173 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
Touch Panel PC Set_Logic_Device proc AHP-2173 near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
Touch Panel PC AHP-2173 Appendix B I/O Information Appendix B I/O Information B-1
Touch Panel PC B.
Touch Panel PC AHP-2173 Appendix B I/O Information B - 3
Touch Panel PC B.
Touch Panel PC AHP-2173 B.3 IRQ Mapping Chart B.
Touch Panel PC AHP-2173 Appendix C AHCI Setting Appendix C AHCI Setting C -1
Touch Panel PC AHP-2173 B.1 Setting AHCI OS installation to setup AHCI Mode.
Touch Panel PC AHP-2173 Step 4: Press “F6” Step 5: Choose “S” Appendix C AHCI Setting C-3
Touch Panel PC AHP-2173 Step 6: Choose “Intel(R) NM10 Express Chipset” Step 7: It will show the model number you select and then press “ENTER Step 8: Setup is loading files, follow the instruction when it's finished Appendix C AHCI Setting C-4