Multi-Touch Panel PC ACP-5210 ACP-5210 21.
Multi-Touch Panel PC ACP-5210 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Multi-Touch Panel PC ACP-5210 Acknowledgments AMD is trademark of Advanced Micro Devices, Inc. Microsoft Windows is a registered trademark of Microsoft ® ® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc. All other product names or trademarks are properties of their respective owners.
Multi-Touch Panel PC ACP-5210 Packing List Before you begin installing your Panel PC, please make sure that the following items have been shipped: ACP-5210 Infotainment Multi-Touch Panel PC Power Adapter x 1 Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Multi-Touch Panel PC ACP-5210 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Multi-Touch Panel PC ACP-5210 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Multi-Touch Panel PC ACP-5210 Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX1 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5.
Multi-Touch Panel PC ACP-5210 FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Multi-Touch Panel PC ACP-5210 UL Module Description ACP-5210 AC modules are developed to suitable for the Classification Mark requirement viii
Multi-Touch Panel PC ACP-5210 Safety Symbol Description The following safety symbols are further explanations for your reference. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1 Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.
Multi-Touch Panel PC ACP-5210 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 六价铬 多溴联苯 多溴二苯醚 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含
Multi-Touch Panel PC ACP-5210 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 General Information................................................... 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions .................................................
Multi-Touch Panel PC ACP-5210 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments ...................................B-5 Appendix C Miscellanea C.1 General Cleaning Tips .......................................... C-2 C.2 Cleaning Tools ...................................................... C-3 C.3 Scrap Computer Recycling ................................. C-5 C.4 Installing Accessories ...........................................
Multi-Touch Panel PC ACP-5210 Chapter 1 General Information Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-5210 1.1 Introduction The ACP-5210 is a Multi-Touch Infotainment Panel PC with superior onboard AMD G-Series T56N processor-based computer. It is a PC-based system with 21.5” Full HD (1920x1080) Fanless TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-5210 includes all the features of a powerful computer into a slim and attractive chassis.
Multi-Touch Panel PC ACP-5210 1.2 Features 21.5” Full HD (1920x1080) Fanless TFT LCD Display Easy-To-Clean: Multi-Touch Window Design (Two-Point) AMD G-Series T56N Processor, 1.
Multi-Touch Panel PC ACP-5210 1.3 Specification System Processor AMD G-Series T56N Processor, 1.6GHz System Memory DDR3 SODIMM x 1, Max. 4 GB (2 GB RAM inside) LCD / CRT Controller AMD A50M Ethernet Realtek 8111E 10/100/1000Base-TX, RJ-45 x 2 I/O Port USB x 4 (Two on Front side, Two on I/O Button side) RS-232 x 1 Line-out x 1 VGA out x 1 Lockable Power Input x 1 Power Switch x 1 Storage Disk Drive 2.
Multi-Touch Panel PC ACP-5210 IPX1 for top plastic chassis Mounting VESA 100, Wallmount Dimension 21.5”(W) x 13.7”(H) x 2.34”(D) (546mm x 348.1mm x 59.4mm) Carton Dimension 26”(W) x 19.52”(H) x 7.87”(D) (661mm x 496mm x 200mm) Gross Weight 18.3 lb (8.
Multi-Touch Panel PC Max. Colors ACP-5210 16.
Multi-Touch Panel PC ACP-5210 1.4 General Information 1.
Multi-Touch Panel PC ACP-5210 VGA USB x 2 Line-out Power connector Smart Card Reader USB x 2 Power Switch COM x 1 USB x 2 LAN x 2 Antenna Antenna Chapter 1 General Information 1-8
Multi-Touch Panel PC ACP-5210 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Multi-Touch Panel PC ACP-5210 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Multi-Touch Panel PC ACP-5210 2.
Multi-Touch Panel PC ACP-5210 Cable Cover (Optional) Note 1: You may turn on the power by cutting and destroying the protective cover as it shows below.
Multi-Touch Panel PC ACP-5210 2.3 2.
Multi-Touch Panel PC Step 3: Remove HDD Bracket (4 screws) Step 4: Get the HDD and HDD Bracket ready Chapter 2 Hardware Installation 2-6 ACP-5210
Multi-Touch Panel PC ACP-5210 Step 5: Fasten the four screws to fix HDD Bracket and HDD Step 6: Connect the SATA and power cables to the HDD and fasten the four screws to fix the HDD Bracket Chapter 2 Hardware Installation 2-7
Multi-Touch Panel PC ACP-5210 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC 3.1 ACP-5210 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Multi-Touch Panel PC 3.2 ACP-5210 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Multi-Touch Panel PC ACP-5210 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Multi-Touch Panel PC ACP-5210 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters Trusted Computing Trusted Computing (TPM) Settings CPU Configuration CPU Configuration Parameters SATA Configuration SATA Device Options Settings USB Configuration USB Configuration Parameters F81866 Super IO Configuration Chapter 3 AMI BIOS Setup 3-5
Multi-Touch Panel PC System Super IO Chip Parameters F81866 H/W Monitor Monitor hardware status Chapter 3 AMI BIOS Setup 3-6 ACP-5210
Multi-Touch Panel PC ACP-5210 ACPI Settings Options summary: (default setting) ACPI Sleep State S3 (Suspend to RAM) Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
Multi-Touch Panel PC ACP-5210 Trusted Computing Options summary: (default setting) TPM SUPPORT Disabled Enabled En/Disable TPM support. O.S. will not show TPM. Reset of platform is required.
Multi-Touch Panel PC ACP-5210 CPU Configuration Chapter 3 AMI BIOS Setup 3-9
Multi-Touch Panel PC ACP-5210 SATA Configuration Options summary: (default setting) OnChip SATA Disabled Channel Enabled En/Disable Serial ATA OnChip SATA Type ACHI Legacy IDE Configure SATA controller operating as Legacy IDE/AHCI mode.
Multi-Touch Panel PC ACP-5210 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables Legacy USB Support. AUTO option disables legacy support if no USB devices are connected.
Multi-Touch Panel PC ACP-5210 If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Multi-Touch Panel PC ACP-5210 F81866 Super IO Configuration Options summary: (default setting) Serial Port 1 Configuration Set Parameters of Serial Port 1 Keep last state Power Failure Always on Always off Select AC power state when power is re-applied after a power failure.
Multi-Touch Panel PC ACP-5210 Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4; IO=2F8h; IRQ=3,4; Select an optimal setting for Super IO device.
Multi-Touch Panel PC ACP-5210 F81866 H/W Monitor Chapter 3 AMI BIOS Setup 3-15
Multi-Touch Panel PC Setup submenu: Chipset Options summary: (default setting) North Bridge South Bridge Parameters South Bridge South Bridge Parameters Chapter 3 AMI BIOS Setup 3-16 ACP-5210
Multi-Touch Panel PC ACP-5210 North Bridge Options summary: (default setting) Graphics Configuration Configure Graphics Settings.
Multi-Touch Panel PC Graphics Configuration Options summary: (default setting) DP1 Output LVDS Disabled NB PCIE Connect Type (Display device) Chapter 3 AMI BIOS Setup 3-18 ACP-5210
Multi-Touch Panel PC ACP-5210 South Bridge Options summary: (default setting) Power Mode ATX Type AT Type Select power supply mode. MiniCard & msata Minicard Configuration mSATA Support MiniCard & msata Device SB HD Azalia Configuration Options for SB HD Azalia.
Multi-Touch Panel PC SB HD Azalia Configuration Options summary: (default setting) HD Audio Azalia Auto Device Disabled Enabled Enable Or Disable HD Audio Azalia Device Chapter 3 AMI BIOS Setup 3-20 ACP-5210
Multi-Touch Panel PC ACP-5210 Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo. Launch RTL8111E Disabled PXE OpROM. Enabled En/Disable PXE boot for RTL8111E LAN Boot Option #x Set the system boot order.
Multi-Touch Panel PC ACP-5210 Setup submenu: Security Options summary: (default setting) Administrator Password/ Not set User Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
Multi-Touch Panel PC ACP-5210 Setup submenu: Save & Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Multi-Touch Panel PC ACP-5210 Chapter 4 Driver Installation Chapter 4 Driver Installation 4 - 1
Multi-Touch Panel PC ACP-5210 The ACP-5210 comes with a DVD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install LAN Driver Step 3 – Install Audio Driver Step 4 – Install AHCI Driver Step 5 – Install Touch Driver Please read instructions below for further detailed installations.
Multi-Touch Panel PC ACP-5210 4.1 Installation: Insert the ACP-5210 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS folder your system is 2. Double click on the Setup.exe located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install LAN Driver 1.
Multi-Touch Panel PC ACP-5210 Step 4 – Install AHCI Driver Please refer to the Appendix D AHCI Setting Step 5 – Install Touch Driver 1. Click on the STEP5-TOUCH folder and select the WINXP_32 folder 2. Double click on ModifyDBArea 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-5210 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-5210 A.1 Programming ACP-5210 utilizes FINTEK 81866 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON attached based program on to fit initial watchdog which you can timer program develop is also customized your application. Configuring Sequence Description After the hardware reset or power-on reset, the FINTEK 81866 enters the normal mode except KBC.
Multi-Touch Panel PC ACP-5210 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode. Undesired result may occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
Multi-Touch Panel PC ACP-5210 Watch Dog Timer 1, 2, 3 Control Register (Index=F5h,F6h,FAh Default=00h) Appendix A Programming the Watchdog Timer A-4
Multi-Touch Panel PC ACP-5210 A.
Multi-Touch Panel PC ACP-5210 Void aaeonWdtSetTimeoutCount(BYTE tTimeout){ f81866SetLdn(0x07); f81866WriteByte(F81866_WDT_TIME_REG, tTimeout); } Void aaeonWdtSetEnable(BOOL bEnable){ f81866SetLdn(0x07); if(bEnable){ f81866WriteByte(0x30, 0x01); WDT_BASE_ADDR = (f81866ReadByte(F81866_WDT_BASEADDR_REG_MSB) << 8) | f81866ReadByte(F81866_WDT_BASEADDR_REG_LSB); WDT_STATUS = f81866ReadByte(F81866_WDT_CONTROL_REG); f81866WriteByte(F81866_WDT_CONTROL_REG, WDT_STATUS | 0x20); WDT_STATUS = f81866ReadByte(F81866_WD
Multi-Touch Panel PC ACP-5210 Void aaeonSuperIOClose(){ aaeonioWritePortByte(F81866_INDEX, 0xaa); } Appendix A Programming the Watchdog Timer A-7
Multi-Touch Panel PC ACP-5210 Appendix B I/O Information Appendix B I/O Information B-1
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5210 Appendix B I/O Information B-3
Multi-Touch Panel PC st B.
Multi-Touch Panel PC ACP-5210 B.3 IRQ Mapping Chart B.
Multi-Touch Panel PC ACP-5210 Appendix C Miscellanea Appendix C Miscellanea C-1
Multi-Touch Panel PC ACP-5210 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
Multi-Touch Panel PC ACP-5210 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals.
Multi-Touch Panel PC ACP-5210 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs - Whenever possible it is better to use lint free swabs such as foam swabs. Note: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below. 1. Close all application programs 2. Close operating software 3.
Multi-Touch Panel PC ACP-5210 C.3 Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform us as soon as possible for the suitable solution. For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.aaeon.
Multi-Touch Panel PC ACP-5210 C.
Multi-Touch Panel PC ACP-5210 MSR Installation Step 1: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the MSR Bracket with the ACP-5210 Appendix C Miscellanea C-7
Multi-Touch Panel PC ACP-5210 Bar Code Scanner Installation Step 1: Fasten the three screws to fix the Bar Code Scanner with the backet Appendix C Miscellanea C-8
Multi-Touch Panel PC ACP-5210 Step 2: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the Bar Code Scanner with the ACP-5210 Appendix C Miscellanea C-9
Multi-Touch Panel PC ACP-5210 Appendix D AHCI Setting Appendix D AHCI Setting D-1
Multi-Touch Panel PC ACP-5210 D.1 Setting AHCI OS installation to setup AHCI Mode. Step 1: Copy the files below from “Driver DVD -> STEP4 AHCI\WinXP\SB8xx_RAID_XP_3.2.1540.
Multi-Touch Panel PC ACP-5210 Step 3: BIOS Setup menu select “Advanced\OnChip SATA Type -> AHCI” Step 4: Setup OS Appendix D AHCI Setting D-3
Multi-Touch Panel PC Step 5: Press “F6” Step 6: Choose “S” Appendix D AHCI Setting D-4 ACP-5210
Multi-Touch Panel PC ACP-5210 ® Step 7: Choose “AMD A50M” Step 8: It will show the model number you select and then press “ENTER” Step 9: Setup is loading files Appendix D AHCI Setting D-5
