Multi-Touch Panel PC ACP-5152 ACP-5152 ® 15.
Multi-Touch Panel PC ACP-5152 Copyright Notice This document is copyrighted, 2011. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Multi-Touch Panel PC ACP-5152 Acknowledgments z Intel®, AtomTM are registered trademarks of Intel® Corporation. z Microsoft® Windows is a registered trademark of Microsoft® Corporation. z RTL is a trademark of Realtek Semi-Conductor Co., Ltd. z C&T is a trademark of Chips and Technologies, Inc. z UMC is a trademark of United Microelectronics Corporation. z ITE is a trademark of Integrated Technology Express, Inc. All other product names or trademarks are properties of their respective owners.
Multi-Touch Panel PC ACP-5152 Packing List Before you begin installing your Medical Station, please make sure that the following items have been shipped: ACP-5152 Infotainment Multi-Touch Panel PC HDD screws Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Multi-Touch Panel PC ACP-5152 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Multi-Touch Panel PC ACP-5152 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Multi-Touch Panel PC ACP-5152 Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX0 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5.
Multi-Touch Panel PC ACP-5152 FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Multi-Touch Panel PC ACP-5152 UL Module Description ACP-5152 AC modules are developed to suitable for the Classification Mark requirement viii
Multi-Touch Panel PC ACP-5152 Safety Symbol Description The following safety symbols are the further explanations for your reference. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1 Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire. Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.
Multi-Touch Panel PC ACP-5152 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量
Multi-Touch Panel PC ACP-5152 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 Dimension ................................................................. 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions .............................................
Multi-Touch Panel PC ACP-5152 B.3 IRQ Mapping Chart ..............................................B-5 B.4 DMA Channel Assignments...................................B-5 Appendix C Miscellanea C.1 General Cleaning Tips .......................................... C-2 C.2 Cleaning Tools...................................................... C-3 C.3 Scrap Computer Recycling ................................. C-5 C.4 Installing Accessories ...........................................
Multi-Touch Panel PC ACP-5152 Chapter 1 General Information Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-5152 1.1 Introduction The ACP-5152 is a Multi-Touch Infotainment Panel PC with superior onboard Intel® AtomTM D510 processor-based computer. It is a PC-based system with 15.6” WXGA(1366 x 768) fanless true color TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-5152 includes all the features of a powerful computer into a slim and attractive chassis.
Multi-Touch Panel PC ACP-5152 1.2 Features z 15.
Multi-Touch Panel PC ACP-5152 1.3 Specification System z Processor Onboard Intel® Atom™ D510 1.66 GHz Processor z System Memory DDR2 SODIMM x 1, Max. 2 GB z LCD / CRT Controller Integrated in Processor z I/O Port USB2.0 x 6 (2 on side; 4 on bottom) RS-232 x 1 Line-out x 1 VGA x 1 z Storage Disk Drive CompactFlash™ slot x 1 (Internal); 2.
Multi-Touch Panel PC ACP-5152 x 230mm) z Net Weight 8.8 lb (4 kg) z Gross Weight 12.1 lb (5.5 kg) Environmental z Operating Temperature 32oF~113oF (0oC~45oC) (Ambient with Airflow) z Storage Temperature -4oF~140oF (-20oC~60oC) z Operating Humidity 10%~95%@ 40oC, non-condensing z Vibration 1 g rms/ 5-500Hz/ Random Operation (HDD) z Shock 15 G peak acceleration (11 msec.
Multi-Touch Panel PC z Backlight MTBF (Hours) ACP-5152 50,000 Touchscreen z Type Projected Capacitive Multi-Touch (Windows® 7) z Light Transmission Chapter 1 General Information 1-6 90%
Multi-Touch Panel PC ACP-5152 1.4 General Information 1.
Multi-Touch Panel PC ACP-5152 Antenna Antenna Power Switch USB2.0 x 2 RS-232 LAN x 2 Line-out VGA USB2.0 x 2 USB2.
Multi-Touch Panel PC ACP-5152 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Multi-Touch Panel PC ACP-5152 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Multi-Touch Panel PC ACP-5152 2.
Multi-Touch Panel PC I/O Cable Cover (Optional) Chapter 2 Hardware Installation 2-4 ACP-5152
Multi-Touch Panel PC ACP-5152 2.3 2.
Multi-Touch Panel PC Step 3: Remove HDD Bracket (4 screws) Step 4: Get the HDD and HDD Bracket ready Chapter 2 Hardware Installation 2-6 ACP-5152
Multi-Touch Panel PC ACP-5152 Step 5: Fasten the four screws to fix HDD Bracket and HDD Step 6: Connect the SATA and power cables to the HDD and fasten the four screws to fix the HDD Bracket Chapter 2 Hardware Installation 2-7
Multi-Touch Panel PC ACP-5152 Step 7: Close the rear cover of ACP-5152 and see if the label of “Mind the high temperature” has been firmly stuck on the rear cover of ACP-5152 Chapter 2 Hardware Installation 2-8
Multi-Touch Panel PC ACP-5152 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC 3.1 ACP-5152 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration against the values stored in the CMOS memory.
Multi-Touch Panel PC 3.2 ACP-5152 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Multi-Touch Panel PC ACP-5152 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Multi-Touch Panel PC ACP-5152 The ACP-5152 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Multi-Touch Panel PC 4.1 ACP-5152 Installation: Insert the ACP-5152 CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1–CHIPSET folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver 1.
Multi-Touch Panel PC ACP-5152 Step 4 –Install LAN Driver 1. Click on the STEP4–LAN folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 – Install WiFi & Bluetooth Driver 1. Click on the STEP5–WIFI&BLUETOOTH folder and select the OS folder your system is 2. Double click on the .exe file located in each OS folder 3.
Multi-Touch Panel PC ACP-5152 Chapter 4 Driver Installation 4-5
Multi-Touch Panel PC Chapter 4 Driver Installation 4-6 ACP-5152
Multi-Touch Panel PC ACP-5152 If you have done installing the G-sensor program, the screen will be rotated automatically when you rotate the ACP-5152.
Multi-Touch Panel PC ACP-5152 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-5152 A.1 Programming ACP-5152 utilizes W83627DHG-P chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application.
Multi-Touch Panel PC ACP-5152 (3) Exit the W83627DHG config Mode. Undesired result may occur if the config Mode is not exited normally. (1) Enter the W83627DHG config Mode To enter the W83627DHG config Mode, two special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform two write operations to the Special Address port (2EH).
Multi-Touch Panel PC = 010 ACP-5152 Power LED pin is driven low. = 011 Power LED pin outputs 2Hz pulse with 50% duty cycle. = 100 Power LED pin outputs 1Hz pulse with 50% duty cycle. = 101 Power LED pin outputs 4Hz pulse with 50% duty cycle. = 110 Power LED pin outputs 0.25Hz pulse with 50% duty cycle. =111 Power LED pin outputs 0.25Hz pulse with 50% duty cycle.. Bit 4 Bit 3 Bit 2 : WDTO# count mode is 1000 times faster. =0 Disable. =1 Enable. : select WDTO# count mode.
Multi-Touch Panel PC ACP-5152 WatchDog Timer Register II (Index=F6h, Default=00h) Bit 7-0 = 0 x 00 Time-out Disable = 0 x 01 Time-out occurs after 1 second/minute = 0 x 02 Time-out occurs after 2 second/minutes = 0 x 03 Time-out occurs after 3 second/minutes ………………………………..
Multi-Touch Panel PC =1 ACP-5152 Force Watchdog Timer time-out event: this bit is self-clearing Bit 4 Bit 3-0 : Watchdog Timer Status. R/W =1 Watchdog Timer time-out occurred =0 Watchdog Timer counting : These bits select IRQ resource for Watchdog. Setting of 2 selects SMI.
Multi-Touch Panel PC ACP-5152 A.2 W83627DHG Watchdog Timer Initial Program Example: Setting 10 sec.
Multi-Touch Panel PC ACP-5152 ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f6h ; CRF6 Out dx,al Inc dx Mov al,10 ;Set timeout interval as 10 sec.
Multi-Touch Panel PC ACP-5152 Appendix B I/O Information Appendix B I/O Information B - 1
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5152 Appendix B I/O Information B - 3
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-5152 B.3 IRQ Mapping Chart B.
Multi-Touch Panel PC ACP-5152 Appendix C Miscellanea Appendix C Miscellanea C-1
Multi-Touch Panel PC ACP-5152 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
Multi-Touch Panel PC ACP-5152 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals.
Multi-Touch Panel PC • ACP-5152 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. • Foam swabs - Whenever possible it is better to use lint free swabs such as foam swabs. Note: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below. 1. Close all application programs 2. Close operating software 3.
Multi-Touch Panel PC ACP-5152 C.3 Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform us as soon as possible for the suitable solution. For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.aaeon.
Multi-Touch Panel PC ACP-5152 C.
Multi-Touch Panel PC ACP-5152 MSR Installation Step 1: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the MSR Bracket with the ACP-5152 Appendix C Miscellanea C-7
Multi-Touch Panel PC ACP-5152 Bar Code Scanner Installation Step 1: Fasten the three screws to fix the Bar Code Scanner with the Appendix C Miscellanea C-8
Multi-Touch Panel PC ACP-5152 backet Step 2: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the Bar Code Scanner with the ACP-5152 Appendix C Miscellanea C-9
Multi-Touch Panel PC Appendix C Miscellanea C-10 ACP-5152
