Multi-Touch Panel PC ACP-1103 ACP-1103 10.1” XGA Open Frame Fanless Multi-Touch Panel PC Intel® AtomTM N2600 Processor RS-232, RS-232/422/485 USB2.
Multi-Touch Panel PC ACP-1103 Copyright Notice This document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Multi-Touch Panel PC ACP-1103 Acknowledgments ® TM ® Intel , Atom are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft ® ® Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc.
Multi-Touch Panel PC ACP-1103 Packing List Before you begin installing your Panel PC, please make sure that the following items have been shipped: ACP-1103 Infotainment Multi-Touch Panel PC RJ-45 Type COM Port Cable x 3 Power Adapter x 1 Product DVD Contains User’s Manual (in PDF format), Drivers and Utilities If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Multi-Touch Panel PC ACP-1103 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Multi-Touch Panel PC ACP-1103 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Multi-Touch Panel PC ACP-1103 Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IPX1 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5.
Multi-Touch Panel PC ACP-1103 FCC This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Multi-Touch Panel PC ACP-1103 Safety Symbol Description The following safety symbols are further explanations for your reference. Attention, consult ACCOMPANYING DOCUMENTS. Ground wire Protective Ground wire.
Multi-Touch Panel PC ACP-1103 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量
Multi-Touch Panel PC ACP-1103 Contents Chapter 1 General Information 1.1 Introduction ................................................................ 1-2 1.2 Features .................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 General Information................................................... 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions .................................................
Multi-Touch Panel PC ACP-1103 2.16 USB 2.0 Port 4 (CN27) ............................................ 2-13 2.17 18-bits LVDS Output (CN15) ................................... 2-13 2.18 HDMI Type C (CN17) .............................................. 2-14 2.19 Inverter / Backlight Connector (CN18) .................... 2-15 2.20 DDR3 SODIMM Slot (DIMM1) ................................ 2-16 2.21 Mini Card Slot (mSATA function only) ..................... 2-16 2.22 Mechanical Drawing of the ACP-1103 ........
Multi-Touch Panel PC ACP-1103 C.2 Cleaning Tools ...................................................... C-3 C.3 Scrap Computer Recycling ................................. C-5 Appendix D AHCI Setting D.1 Setting AHCI ......................................................... D-2 Appendix E Digital I/O Ports E.1 Electrical Specifications for Digital I/O Ports .........E-2 E.2 DIO Programming ..................................................E-2 E.3 Digital I/O Register .....................................
Multi-Touch Panel PC ACP-1103 Chapter 1 General Information Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-1103 1.1 Introduction The ACP-1103 is a Multi-Touch Industrial Panel PC with onboard ® Intel Atom™ N2600 processor-based computer. It is a PC-based system with 10.1” true color TFT LCD display, integrated multimedia functions make them the perfect platforms to build comprehensive lifestyle computing applications. The ACP-1103 includes all the features of a powerful computer into a slim and attractive mechanism design.
Multi-Touch Panel PC ACP-1103 1.2 Features 10.
Multi-Touch Panel PC ACP-1103 1.3 Specification System Processor ® Onboard Intel Atom™ N2600 Processor System Memory DDR3 SODIMM x 1, Max. 2 GB (Default is 2G RAM) ® LCD / CRT Controller Integrated graphics in Intel NM10 I/O Port RS-232 x 1 (RJ-45 connector) RS-232/422/485 x 2 (RJ-45 connector) LAN x 1 (RJ-45 connector) USB2.
Multi-Touch Panel PC ACP-1103 x 183.5mm x 30mm) Carton Dimension 13.58” x 7.87” x 9.65’’ (345mm x 200mm x 245mm) Net Weight 2.42 lb (1.1 kg) Gross Weight 5.5 lb (2.5 kg) Environmental o o o o o o o o Operating Temperature 14 F~113 F (-10 C~45 C) Storage Temperature 14 F~122 F (-10 C~50 C) Storage Humidity 10%~90% @ 40 C, non-condensing Vibration 1 g rms/ 5-500Hz/ Random Operation o (HDD) Shock 20 G peak acceleration (11 msec.
Multi-Touch Panel PC ACP-1103 Viewing Angle 160º (H), 160º (V) Backlight MTBF (Hours) 50,000 Touchscreen Type Projected Capacitive Multi-Touch (Two points) Resolution 2048x2048 Light Transmission >90% Chapter 1 General Information 1-6
Multi-Touch Panel PC ACP-1103 1.
Multi-Touch Panel PC ACP-1103 Antenna VESA mount Chapter 1 General Information 1-8
Multi-Touch Panel PC ACP-1103 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Multi-Touch Panel PC ACP-1103 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Multi-Touch Panel PC ACP-1103 2.
Multi-Touch Panel PC ACP-1103 2.3 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
Multi-Touch Panel PC ACP-1103 2.4 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
Multi-Touch Panel PC ACP-1103 2.5 Clear CMOS Jumper (JP2) 1 2 3 Normal (Default) JP2 Function 1-2 Normal (Default) 2-3 Clear CMOS 1 2 3 Clear CMOS 2.6 LVDS Port 1 Backlight Inverter VCC Selection (JP3) 1 2 3 +12V JP3 Function 1-2 +12V 2-3 +5V (Default) 1 2 3 +5V (Default) 2.7 LVDS Port 1 Operating VDD Selection (JP5) 1 2 3 +5V JP5 Function 1-2 +5V 2-3 +3.3V (Default) Chapter 2 Hardware Installation 2-6 1 2 3 +3.
Multi-Touch Panel PC ACP-1103 2.8 AT/ATX Power Supply Mode Selection (JP6) 1 2 3 1 2 3 AT Mode ATX Mode(Default) JP6 Function 1-2 AT Mode 2-3 ATX Mode(Default) 2.
Multi-Touch Panel PC ACP-1103 2.
Multi-Touch Panel PC ACP-1103 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 NC Note: 1700090156 External COM Port Converter Cable 2.
Multi-Touch Panel PC 6 DCD 7 CTS 8 DTR ACP-1103 DATA- TX- RX- COM2, COM3 Pin Signal Pin Signal 1 DCD (422TXD-/485DATA-) 2 RXD (422TXD+/485DATA+) 3 TXD (422RXD+) 4 DTR(422RXD-) 5 GND 6 DSR 7 RTS 8 CTS 9 NC Note: 1700090156 External COM Port Converter Cable Chapter 2 Hardware Installation 2-10
Multi-Touch Panel PC ACP-1103 2.12 Buzzer (CN8) Pin Pin Name Signal Type Signal Level 1 +3.3V PWR +3.3V 2 SPK OUT 2.13 RESET (CN9) Pin Pin Name Signal Type Signal Level 1 RESET IN +3.3V 2 GND GND 8 DTR OUT 2.14 LPC Debug Port (CN10) LAD0 LAD1 LAD2 LAD3 +3.
Multi-Touch Panel PC ACP-1103 Pin Pin Name Signal Type Signal Level 1 LAD0 I/O +3.3V 2 LAD1 I/O +3.3V 3 LAD2 I/O +3.3V 4 LAD3 I/O +3.3V 5 +3.3V PWR +3.3V 6 LFRAME# IN 7 LRESET# OUT 8 GND GND 9 LCLK OUT 10 LDRQ0 IN 11 LDRQ1 IN 12 SERIRQ I/O +3.3V +3.3V 2.15 USB 2.
Multi-Touch Panel PC 5 ACP-1103 GND GND 2.16 USB 2.0 Port 4 (CN27) Pin Pin Name Signal Type Signal Level 1 +5V PWR +5V 2 USB4_D- DIFF 3 USB4_D+ DIFF 4 GND GND 5 GND GND 6 WIR_DIS SINGLE 2.17 18-bits LVDS Output (CN15) Pin Pin Name Signal Type 1 BKL_ENABLE OUT 3 LCD_PWR 5 LVDS_A_CLK- DIFF 7 LVDS_A_CLK+ DIFF Signal Level +3.
Multi-Touch Panel PC ACP-1103 9 LCD_PWR DIFF +3.3V/+5V 11 LVDS_DA0+ DIFF 13 LVDS_DA0- DIFF 15 GND GND 17 LVDS_DA1+ DIFF 19 LVDS_DA1- DIFF 2 BKL_CONTROL OUT 4 LCD_PWR PWR 6 LVDS_DA2+ DIFF 8 LVDS_DA2- DIFF 10 GND GND 12 LVDS_DA3+ DIFF 14 LVDS_DA3- DIFF 16 GND GND 18 DDC_DATA I/O +3.3V 20 DDC_CLK I/O +3.3V Signal Level +3.3V/+5V 2.
Multi-Touch Panel PC ACP-1103 5 HDMI_TX1+ DIFF 7 GND GND 9 HDMI_TX0- DIFF 11 HDMI_CLK+ DIFF 13 GND GND 15 HDMI_DDC_CLK I/O 17 NC NC 19 DPD_PWR PWR 2 HDMI_TX2+ DIFF 4 GND GND 6 HDMI_TX1- DIFF 8 HDMI_TX0+ DIFF 10 GND GND 12 HDMI_CLK- DIFF 14 NC NC 16 HDMI_DDC_DATA I/O 18 DPD_HPD IN +5V +5V +5V 2.
Multi-Touch Panel PC ACP-1103 Pin Pin Name Signal Type Signal Level 1 BKL_PWR PWR +5V / +12V 2 BKL_CONTROL OUT 3 GND GND 4 GND GND 5 BKL_ENABLE OUT +5V 2.20 DDR3 SODIMM Slot (DIMM1) Standard specification 2.
Multi-Touch Panel PC ACP-1103 25 mSATA_RX- DIFF 27 GND GND 29 GND GND 31 mSATA_TX- DIFF 33 mSATA_TX+ DIFF 35 GND GND 37 GND GND 39 +3.3V PWR +3.3V 41 +3.3V PWR +3.3V 43 NC 45 NC 47 NC 49 NC 51 NC 2 +3.3V PWR +3.3V 4 GND GND 6 +1.5V PWR 8 NC 9 NC 10 NC 12 NC 14 NC 18 GND 20 NC +1.
Multi-Touch Panel PC ACP-1103 22 NC 24 +3.3V PWR 26 GND GND 28 +1.5V PWR +1.5V 30 SMB_CLK I/O +3.3V 32 SMB_DATA I/O +3.3V 34 GND GND 36 NC 38 NC 40 GND 42 NC 44 NC 46 NC 48 +1.5V PWR 50 GND GND 52 +3.3V PWR Chapter 2 Hardware Installation 2-18 +3.3V GND +1.5V +3.
Multi-Touch Panel PC ACP-1103 2.22 Mechanical Drawing of the ACP-1103 30 136 7 9 .6 1 8 3 .5 5 2 6 5 .
Multi-Touch Panel PC ACP-1103 2.23 How to Embed the ACP-1103 Step 1: Get the wallmount bracket and sponge ready. Sponge Wall mount bracket Step 2: Unfasten the six screws (three screws on each side respectively) and put the wallmount bracket to ACP-1103. Then, fasten the original six screws back to the ACP-1103.
Multi-Touch Panel PC ACP-1103 Step 4: Insert the ACP-1103 to the place (opening) where you are going to 2 embed the ACP-1103 Opening wall Step 5: Insert the mounting clips to the four fillisters on wallmount bracket 3 and fasten the four M4x60 screws to lock the bracket 2 M4x60 screw 1 4-mounting clip Chapter 2 Hardware Installation 2-21
Multi-Touch Panel PC ACP-1103 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC ACP-1103 3.1 System Test and Iinitialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM.
Multi-Touch Panel PC ACP-1103 3.2 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Multi-Touch Panel PC ACP-1103 Setup Menu Setup submenu: Main Options summary: (default setting) System Date Day MM:DD:YYYY Change the month, year and century. The ‘Day’ is changed automatically. System Time HH : MM : SS Change the clock of the system.
Multi-Touch Panel PC ACP-1103 Setup submenu: Advanced Options summary: (default setting) ACPI Settings System ACPI Parameters CPU Configuration CPU Configuration Parameters IDE Configuration IDE Device Options Settings USB Configuration USB Configuration Parameters F81801 Super IO Configuration System Super IO Parameters Chapter 3 AMI BIOS Setup 3-5
Multi-Touch Panel PC F81216 Second Super IO Configuration System Second Super IO Parameters Digital IO Port Configuration DIO configuration H/W Monitor Monitor hardware status Chapter 3 AMI BIOS Setup 3-6 ACP-1103
Multi-Touch Panel PC ACP-1103 ACPI Settings Options summary: (default setting) Enabled Enable Hibernation Disabled Enabled or disabled hibernate (OS/S4 Sleep State).
Multi-Touch Panel PC Disabled Enabled or disabled wake on ring function. RTC Wake Settings Enable system to wake from S5 using RTC alarm.
Multi-Touch Panel PC ACP-1103 RTC Wake Settings Options summary: (default setting) Wake system with Fixed Disabled Time Enabled Enable or disable System wake on alarm event. Wake up time is setting by following settings.
Multi-Touch Panel PC Wake up minute 0-59 Wake up second 0-59 Wake system with Disabled Dynamic Time Enabled ACP-1103 Enable or disable System wake on alarm event. Wake up time is current time + Increase minutes.
Multi-Touch Panel PC ACP-1103 CPU Configuration Options summary: (default setting) Hyper-Threading Disabled Enabled En/Disable CPU Hyper-Threading function Execute Disable Bit Disabled Enabled En/Disable XD bit for supporting OS Limit CPUID Maximum Disabled Enabled Disabled for Windows XP CPU Smart Thermal Control Disabled Chapter 3 AMI BIOS Setup 3-11
Multi-Touch Panel PC ACP-1103 55 60 65 70 CPU will reduce frequency automatically when CPU temperature higher than the setting value.
Multi-Touch Panel PC ACP-1103 IDE Configuration Options summary: (default setting) SATA Controller(s) Disabled Enabled En/Disable SATA controller Configure SATA as IDE AHCI Configure SATA controller operating as IDE/AHCI mode.
Multi-Touch Panel PC ACP-1103 USB Configuration Options summary: (default setting) Legacy USB Support Enabled Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected.
Multi-Touch Panel PC ACP-1103 Forced FDD Hard Disk CD-ROM If Auto. USB devices less than 530MB will be emulated as Floppy and remaining as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex.
Multi-Touch Panel PC F81801 Super IO Configuration Options summary: (default setting) Serial Port 1/2 Configuration Set Parameters of Serial Port 1/2 Chapter 3 AMI BIOS Setup 3-16 ACP-1103
Multi-Touch Panel PC ACP-1103 Serial Port 1 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Multi-Touch Panel PC Select a resource setting for Super IO device.
Multi-Touch Panel PC ACP-1103 Serial Port 2 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port.
Multi-Touch Panel PC ACP-1103 Select a resource setting for Super IO device. Device Type RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
Multi-Touch Panel PC ACP-1103 F81216 Second Super IO Configuration Options summary: (default setting) Serial Port 3 Configuration Set Parameters of Serial Port 3 Chapter 3 AMI BIOS Setup 3-21
Multi-Touch Panel PC ACP-1103 Serial Port 3 Configuration Options summary: (default setting) Serial Port Disabled Enabled En/Disable specified serial port. Change Settings Auto IO=2C0h; IRQ=5; IO=2C0h; IRQ=3,4,5,9,10,11; IO=2C8h; IRQ=3,4,5,9,10,11; IO=2B0h; IRQ=3,4,5,9,10,11; IO=2B8h; IRQ=3,4,5,9,10,11; Select a resource setting for Super IO device.
Multi-Touch Panel PC Device Type ACP-1103 RS232 RS422 RS485 Configure COM2 operated as RS232, RS422 or RS485.
Multi-Touch Panel PC H/W Monitor Chapter 3 AMI BIOS Setup 3-24 ACP-1103
Multi-Touch Panel PC ACP-1103 Setup submenu: Chipset Options summary: (default setting) Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters Chapter 3 AMI BIOS Setup 3-25
Multi-Touch Panel PC ACP-1103 Host Bridge Options summary: (default setting) Fixed Graphics Memory 128MB Size 256MB Configure Fixed Graphics Memory Size IGFX – Boot Type LVDS HDMI Select the Video Device which will be activated during POST.
Multi-Touch Panel PC ACP-1103 South Bridge Options summary: (default setting) Onboard Devices Onboard devices parameters configurations High Precision Timer Enabled Disabled Enable or Disable the High Precision Event Timer Power Mode ATX Type AT Type Select the power type used on the system SLP_S4 Assertion Width 1-2 Seconds 2-3 Seconds Chapter 3 AMI BIOS Setup 3-27
Multi-Touch Panel PC ACP-1103 3-4 Seconds 4-5 Seconds Select a minimum assertion width of the SLP_S4# signal Restore AC Power Loss Power On Power Off Last State Select AC power state when power is re-applied after a power failure.
Multi-Touch Panel PC ACP-1103 Onboard Devices Options summary: (default setting) Azalia Controller Disabled HD Audio Select a OnBoard Azalia Configuration LAN Controller Disabled Enabled Enable or disable Realtek R8111E PCIE LAN Device SMBus Controller Disabled Enabled Enable or Disable OnChip SMBus Controller Chapter 3 AMI BIOS Setup 3-29
Multi-Touch Panel PC Setup submenu: Boot Options summary: (default setting) Quiet Boot Disabled Enabled En/Disable showing boot logo. Launch LAN PXE OpROM Disabled Enabled En/Disable PXE boot for RTL8111E LAN Boot Option #X/ XXXX Drive BBS Priorities The order of boot priorities.
Multi-Touch Panel PC ACP-1103 BBS Priorities Options summary: (default setting) Boot Option #x Disabled Device name Sets the system boot order Chapter 3 AMI BIOS Setup 3-31
Multi-Touch Panel PC ACP-1103 Setup submenu: Security Options summary: (default setting) Administrator Password/ Not set User Password You can install a Supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the Setup utility. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
Multi-Touch Panel PC ACP-1103 required at boot time, or when the user enters the Setup utility. Removing the Password: Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection.
Multi-Touch Panel PC ACP-1103 HDD Security Options summary: (default setting) Set User Password/ Not set Set Master Password You can install a Master and User password. Before booting to OS, HDD will be set to frozen state. On S3 resume HDD will be unlocked using the HDD Password we entered while system booting. Install the Password: Press Enter on this item, a dialog box appears which lets you enter a password. You can enter no more than six letters or numbers.
Multi-Touch Panel PC ACP-1103 required at boot time, or when the user enters the Setup utility. Removing the Password: Highlight this item and type in the current password. At the next dialog box press Enter to disable password protection.
Multi-Touch Panel PC Setup submenu: Exit Options summary: (default setting) Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving any changes Restore Defaults Restore/Load Default values for all the setup options.
Multi-Touch Panel PC ACP-1103 Restore the User Defaults to all the setup options Chapter 3 AMI BIOS Setup 3-37
Multi-Touch Panel PC ACP-1103 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Multi-Touch Panel PC ACP-1103 The ACP-1103 comes with an AutoRun CD-ROM that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver CD, the driver CD-title will auto start and show the installation guide. If not, please follow the sequence below to install the drivers.
Multi-Touch Panel PC 4.1 ACP-1103 Installation: Insert the ACP-1103 CD-ROM into the CD-ROM drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-Chipset folder and select the OS folder your system is 2. Double click on the infinst_autol_1034.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 2 – Install VGA Driver ® For Windows 7 1.
Multi-Touch Panel PC ACP-1103 4. The system will help you install the driver automatically Step 3 –Install LAN Driver 1. Click on the STEP3-LAN folder and select the OS folder your system is 2. Double click on the setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-1103 Chapter 4 Driver Installation 4-5
Multi-Touch Panel PC Chapter 4 Driver Installation 4-6 ACP-1103
Multi-Touch Panel PC ACP-1103 Step 6 – Install Wireless Driver (Optional) 1. Click on the STEP6-Wireless (Optional) folder and select the OS folder your system is 2. Double click on the VN9271_Windows_V1.3.0.0_x86.exe file located in each OS folder 3. Follow the instructions that the window shows 4.
Multi-Touch Panel PC ACP-1103 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-1103 A.1 Watchdog Timer Registers Table 1 : Watch dog relative IO address Default Value I/O Base Address Note I/O Base address for Watchdog operation. 0xA00 This address is assigned by SIO LDN7, register 0x60-0x61.
Multi-Touch Panel PC ACP-1103 A.
Multi-Touch Panel PC ACP-1103 // This procudure will enable the WDT counting.
Multi-Touch Panel PC ACP-1103 // WDT output pulse width is 25ms WDTSetBit(TimerReg, PSWidthBit, PSWidthVal); // Watchdog WDTRST# Enable WDTSetBit(DevReg, WDTRstBit, WDTRstVal); } VOID WDTClearTimeoutStatus(){ WDTSetBit(TimerReg, StatusBit, 1); } ************************************************************************** ************************************************************************** VOID WDTWriteByte(byte Register, byte Value){ IOWriteByte(WDTAddr+Register, Value); } byte WDTReadByte(byte Regist
Multi-Touch Panel PC ACP-1103 Appendix B I/O Information Appendix B I/O Information B-1
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-1103 Appendix B I/O Information B-3
Multi-Touch Panel PC B.
Multi-Touch Panel PC ACP-1103 B.
Multi-Touch Panel PC Appendix B I/O Information B-6 ACP-1103
Multi-Touch Panel PC ACP-1103 B.
Multi-Touch Panel PC ACP-1103 Appendix C Miscellanea Appendix C Miscellanea C-1
Multi-Touch Panel PC ACP-1103 C.1 General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. Never spray or squirt the liquids directly onto any computer component. If you need to clean the device, please rub it with a piece of dry cloth. 2. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
Multi-Touch Panel PC ACP-1103 C.2 Cleaning tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals.
Multi-Touch Panel PC ACP-1103 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs - Whenever possible it is better to use lint free swabs such as foam swabs. Note: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below. 1. Close all application programs 2. Close operating software 3.
Multi-Touch Panel PC ACP-1103 C.3 Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform us as soon as possible for the suitable solution. For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.aaeon.
Multi-Touch Panel PC ACP-1103 Appendix D AHCI Setting Appendix D AHCI Setting D-1
Multi-Touch Panel PC ACP-1103 D.1 Setting AHCI OS installation to setup AHCI Mode.
Multi-Touch Panel PC ACP-1103 Step 3: Setup OS Step 4: Press “F6” Appendix D AHCI Setting D-3
Multi-Touch Panel PC ACP-1103 Step 5: Choose “S” Step 6: Choose “Intel(R) NM10 Express Chipset” Appendix D AHCI Setting D-4
Multi-Touch Panel PC ACP-1103 Step 7: It will show the model number you select and then press “ENTER Step 8: Setup is loading files Appendix D AHCI Setting D-5
Multi-Touch Panel PC ACP-1103 Appendix E Digital I/O Ports Appendix E Digital I/O Ports E-1
Multi-Touch Panel PC ACP-1103 E.1 Electrical Specifications for Digital I/O Ports Table 1 : Digital Input/Output Pin Electrical Specification Pin Type Input Threshold Voltage Output Voltage Low High Low High DIO1 I/O 0.8 2.0 0 3.3 DIO2 I/O 0.8 2.0 0 3.3 DIO3 I/O 0.8 2.0 0 3.3 DIO4 I/O 0.8 2.0 0 3.3 Note Note: All DIO pins are 5V tolerance in input mode. E.2 DIO Programming ACP-1103 utilizes FINTEK F81801U chipset as its Digital I/O controller.
Multi-Touch Panel PC ACP-1103 E.
Multi-Touch Panel PC ACP-1103 E.
Multi-Touch Panel PC ACP-1103 // Procedure : AaeonSetOutputLevel // Input : // Example, Set Digital I/O Pin 2 to high level AaeonSetOutputLevel(Pin2Bit, PinHigh); } ************************************************************************** ************************************************************************** Boolean AaeonReadPinStatus(byte PinBit){ Boolean PinStatus ; PinStatus = SIOBitRead(DIOLDN, StatusReg, PinBit); Return PinStatus ; } VOID AaeonSetOutputLevel(byte PinBit, byte Value){ ConfigDioMo
Multi-Touch Panel PC ACP-1103 Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= ~(1 << BitNum); TmpValue |= (Value << BitNum); IOWriteByte(SIOData, TmpValue); SIOExitMBPnPMode(); } VOID SIOByteSet(byte LDN, byte Register, byte Value){ SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); IOWriteByte(SIOData, Value); SIOExitMBPnPMode(); } *********************************************************************
Multi-Touch Panel PC ACP-1103 ************************************************************************** Boolean SIOBitRead(byte LDN, byte Register, byte BitNum){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(LDN); IOWriteByte(SIOIndex, Register); TmpValue = IOReadByte(SIOData); TmpValue &= (1 << BitNum); SIOExitMBPnPMode(); If(TmpValue == 0) Return 0; Return 1; } VOID ConfigDioMode(byte PinBit, byte Mode){ Byte TmpValue; SIOEnterMBPnPMode(); SIOSelectLDN(DIOLDN); IOWriteByte(SIOIndex, DirReg); TmpValu
