User`s guide

Specifications
Oscar Laser Gaming Mouse
MODEL: XL-755K, XL-740K, XL-730K,
XL-750K, XL-750BK, XL-750MK, XL-771K,
XL-770K,XL-83K,XL-85K
Oscar Optical Gaming Mouse
MODEL: X-738K,X-718BK,X-748K
Oscar Optical Gaming Mouse
MODEL: X-755K, X-710K, X-710BK,
X-710MK, X-705K
3,600 DPI X7 Laser Engine
）
• FPS: 7080 Frames / Second
• Image Processing: 6.4 mega
pixels/second
• SPI Time: 1ms
• Maximum Acceleration: 20g
• Maximum Speed: 45 inches / second*
(*Depending on surface)
• Cable Diameter: 30 mms
• Cable Length: 1.8 Meters
• Button Lifetime: 8,000,000 Clicks
• Mouse Feet Lifetime: 250 Kilometers
3,200 DPI X7 Optical Engine
• Key Response Time (3X Fire Button, Left
& Right Button): 3-30ms
• Adjustable Resolution: 100~3200 DPI
• Default DPI Modes：600 – 800 -1200
-1600 -2400 -3200 DPI
• Adjustable USB Report Rate:
125-250-500-1000Hz（USB Full Speed）
• FPS: 6500
• Image Proce
pixels/second
• SPI Time: 1ms
• Maximum Accelerat on: 15g
• Maximum Speed: 0 inches /second*
• Key Response Time (3X Fire Button、Left
& Right Button): 3-30ms
• Adjustable Resolution: 100~3600 DPI
• Default DPI Modes：600 - 800 - 1200 -
1600 - 2000 - 3600 DPI
• Adjustable USB Report Rate:
125-250-500-1000Hz（USB Full Speed
Frames / Second
ssing: 5.8 mega
i
4
(*Depending on s rface)
• Cable Diameter: 30 mms
• Cable Length: 1.8 M ters
• Button Li s
• Mouse Feet Lifetime: 250 Kilometers
2,000
• Key Resp
Right Button
• Adjustabl
• Default DP
- 2000 DPI
• Adjustable USB Report Rate:
125-250-500-1000Hz（USB Full Speed）
• FPS: 6500 Frames / Second
• Image Processing: 5.8 mega pixels /
second
• SPI Time: 1ms
• Maximum Acceleration: 15g
• Maximum Speed: 40 inches / second*
(*Depending on surface)
• Cable Diameter: 30 mms
• Cable Length: 1.8 Meters
• Button Lifetime: 8,000,000 Clicks
• Mouse Feet Lifetime: 250 Kilometers
u
e
fetime: 8,000,000 Click
DPI X7 Optical Engine
onse Time (3X Fire Button, Left &
): 3-30ms
e Resolution: 100~2000 DPI
I Modes：400 - 800 - 1200 - 1600
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient of relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z
z
z