Powered by User Manual English This manual covers all the details and explanations of the TEASI CORE.
Table of Contents The use and operation of navigation systems .................................................................................. 3 Teasi Core ......................................................................................................................................... 3 1. Getting to know your Core ....................................................................................................... 4 2. Charging the Teasi Core .................................................
The use and operation of navigation systems Attention! Don’t operate with the device while driving. Even the smallest and shortest distractions from road or traffic for you and other road users - even at slow speeds – may have devastating consequences. Type in the destination before starting your journey and start the navigation system before you start driving. If you have to change the route or the settings while driving, you should better stop for it.
1. Getting to know your Core 4 2 A 5 6 3 B1 C 1. USB charging interface/USB rubber stopper 3. Reset 5. Auto backlight on/off induction window 2. Long press: power on/off short press: backlight on/off 4. Buzzer 6.
2. Charging the Teasi Core 1. 2. 3. 4. Pull up the USB rubber stopper from the USB charging interface (1). Plug the small end of the USB cable in the USB charging interface. Connect the large end of the USB cable to a 5V AC adaptor or a USB port on a computer. Charge the Teasi Core for the first time completely, around 4 hours. The average charging time is 1.5 hours. When the battery is completely discharged, the device may only turn on after the battery has been charged for some time.
5. Installation of Teasi Core on your bicycle Fix the Teasi Core on the bracket as shown in the figure below. 6. Installation of speed/cadence sensor Install pedals magnet (RPM) and wheel magnet (speed) in corresponding positions as shown in the figure below: Tear the 3M adhesive on the back of pedal magnet off and stick pedals magnet inside the pedal connecting arm, and then tie up the 2 nylon straps to fix it, and cut unnecessary part down.
Fix speed/cadence sensor on corresponding position of bike as shown in the figure, and then tighten it with 2 nylon straps. Then, fix it again with a rubber band. Please note: the centers of pedal magnet and wheel magnet shall be aligned with corresponding induction part of sensor and shall not be deviated from it too far; the magnets shall not be more than 2 cm from the induction part, since distance larger than 2 cm will make it fail to receive the wheel spinning signal.
7. Teasi Core has 2 working modes a) App working mode: Teasi Core is only a display equipment that needs to pair and connect to app, and all its data is from app push; in this mode, speed/cadence sensor and heart rate monitor shall pair with Teasi Core and connect to it. b) Bike computer working mode: Teasi Core is only a bike computer that is not connected to app; in this mode, speed/ cadence sensor and heart rate monitor shall pair with Teasi Core and connect to it. 7.1 App working mode 7.1.
Notice: Please make sure your phone and Teasi Core have enough power before updating, keep Bluetooth connection smooth in updating process, and do not take your phone away from Teasi Core. If update does not progress for a long time or power fails, or Bluetooth signal is lost in updating process, Teasi Core will return to its old version and will update again when it is connected to the app next time.
7.1.2 Speedometer Display of Teasi Core Speedometer Successful connection to Tahuna Smartphone battery Smartphone GPS on Current time Equipment battery Maximum speed Current speed Accumulative mileage After the equipment is connected to Tahuna, the 2 data types can be changed on the app in the speedometer view.
7.1.3 Page Display of Teasi Core Display page of Teasi Core is divided into: Speedometer, 2-4-6 segment display interface, navigation display interface. Users can change the data type they want to display on the corresponding page of the app for the two data fields below (speedometer and navigation picture), and the data on 2-4-6 interface. Data fields with red dots in this document can be changed. Users can select corresponding 2-4-6 segment display mode on app computer page according to their habits.
This product will enter standby mode automatically after riding is stopped for 3 min, as shown in the figure below. It will return to the previous interface automatically after riding starts again. Standby Mode 7.2 Bike Computer Mode This product will seek to connect with Tahuna after it is started, as shown in the figure below; if you do not want to connect with Tahuna or Tahuna has stopped working, you can press the far left button to EXIT and enter bike computer mode.
7.2.1 Manual pairing method for sensors and Teasi Core If sensors won’t connect automatically, you can connect them manually. Make sure that the sensors have been activated for operation. Speed & Cadence Sensor: The magnets must pass the sensor surfaces to activate the sensor. Heart rate sensor: Must have secure skin contact with lightly moistened contact surfaces.
When bike computer is working, users can record and store sports data selectively. Short press to start record and short press again to suspend recording; long press for 1 sec, and then release it after hearing the buzzer sounds once to stop recording; a new entry of record is generated. When the equipment is connected to Tahuna again, Tahuna will acquire this data and calculate it. 7.2.
Perimeter: Wheel perimeter, see table in 7.3.2 Wheel size setting. Clear pair info: Eliminate Bluetooth pairing information. Clear sport data: Eliminate all sports data except for ODO data. Reset to default: Reset to factory defaults, settings data will be cleared after resetting to default. 7.3.2 Wheel size setting In the table below, you can find the wheel size (L) of your tire, or the actually measured wheel size (L) of your bike.
8. Connect the Teasi Core to the Tahuna App Open the Tahuna application. Please make sure first that you have logged in and you have a stable internet connection. Enter into the Shop menu by tapping on the plus sign button ( the screen. Always follow the plus sign in the next steps. ) at the bottom right side of In the Shop menu, tap on the plus sign, next to Hardware Packages to see what kind of extra hardware options are there.
In Hardware Packages, you can choose Bike Computer Package by tapping on the plus sign next to them. In this case, choose Bike Computer. At the next screen, details about the product are shown. Tap on the plus sign to install Bike Computer Package.
In order to connect Bike Computer with the Tahuna Application, Bluetooth must be turned on on your phone. Tap on ‘Next’ when Bluetooth is ready. The App will search for devices. The App will search for devices.
Two outcomes are possible: Bluetooth connection failed. In this case, you should check, if Bluetooth connection is really turned on or not. Connecting devices have been successful. New features have been unlocked with this step: - Navigation package, - Fitness/Sensor package, - Gadget package.
9. Connection The starting screen of the application is a map. If you would like to get to the main menu, tap the button with 3 lines at the top left side of the screen. The application’s Main menu will appear. Tap on the gear wheel at the bottom left side of the screen to open the Settings menu.
The content of Settings menu appears. It has a submenu panel. Choose Sensors by sliding the submenu panel. Please make sure Teasi Core is switched on and searching for smart phones. The app will do a scanning whether there is any BLE device nearby.
After the scans, it will show what it has found. Search for the sign ‘TEASI CORE’ with a green icon. It is disconnected on default. Tap on it, so it can start connecting. If your Teasi Core cannot be found, use the Reset arrow to update the status of the search. Sensors connect automatically to the app when they are ready for operation and active. Speed & Cadence Sensor: The magnets must pass the sensor surfaces to activate the sensor.
10. Computer layout and selection change Tap Computer in the main menu. Computer menu appears. It has a submenu panel, Tap Computers menu point. There is a button next to the reset arrow called the Layout button. It can split up the show of the data into groups of 2, 4 or 6 parts. The button always shows the next layout type. You can change the computer type by long pressing on the box you want to modify and selecting from the list. Every information is then synchronized with Teasi Core.
11. Navigation (turn instructions to Teasi Core) During the navigation in the Tahuna App, the next turning instruction will be shown. When connection has been established, the arrows will appear also on the screen of the Teasi Core. Furthermore, other related data in the Computer section will appear also on Teasi Core, too.
12. Troubleshooting Problem Device stops responding Device does not reconnect to app Speed/cadence sensors are not found in bike computer mode Speed/cadence sensors are not found in app mode Firmware update gets stuck Clearing user data/Restore factory settings Device does not power on Solution Press reset button on the rear side. This does not erase your data or settings. Turn device off and on again, go to the settings in the app and press on the Sensors tab.
14. Appendix 14.
User information/Contact If your device has a defect or you have problems with it, please contact our Service & Support Centre. If you need to send your device to us, please attend to the following points: 1. Whenever possible, use the original packaging. 2. Add a detailed error description 3. Add your full name and address and a copy of your purchase receipt. 4. Stamp and send the package to us (sufficient postage). Address of our Service Center: First Service Center, Kleine Düwelstr.
