ANI-MOD INSTRUCTION MANUAL ANI-MOD Series: Modular Matrix Switcher A-NeuVideo.com Frisco, Texas 75034 (317) 456-2461 V3.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Keep unit protected from rain, water and excessive moisture. 4.
A NEUVIDEO TABLE OF CONTENTS CONTENTS Package Contents .........................................................................1 SAFETY PRECAUTIONS Introduction / Features ....................................................................2 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
A NEUVIDEO INTRODUCTION & FEATURES INTRODUCTION A-Neuvideo’s ANI-MOD series is a high-performance video and audio modular matrix switcher supporting up to 64 input and 64 output signal sources. It supports different video signals with cross switching. Every video or audio signal is transmitted and switched independently to decrease signal attenuation. ANI-MOD supports various changeable cards including HMDI, DVI, VGA, SDI and HDBaseT™ etc, and all the cards support hot plug & play.
A NEUVIDEO SPECIFICATIONS Main Unit Control Parts General Serial Control Port RS-232, 9-pin female D connector Power Supply 100VAC ~ 240VAC, 50/60Hz Installation Rack Mountable Temperature 14~104°F (-10 ~+40°C) Pin Configurations 2 = TX, 3 = RX, 5 = GND Power Consumption 200W (max) Front panel control Buttons Humidity 10% ~ 90% Options TCP/IP control by external device. Switcher does not include a build-in web server. Case Dimension (WxHxD) Product Weight ANI-MOD88 19 x 3.5 x 12.
A NEUVIDEO ani-mod88 Front Panel Operation ANI-MOD88: The front panel of ANI-MOD88 is shown as below. r w q e y t 1. IR: IR sensor, receive IR signal sent from IR remote 2. Power Indicator: Illuminate red once powered on 3. LCD Screen: Display real-time operation status 4. INPUTS: Buttons for input channels with green back-light indicating, ranges from 1~ 8, (8) selectable channels in total 5.
A NEUVIDEO FRONT & back PANEL Front Panel Operation ANI-MOD1616/ANI-MOD3232/ANI-MOD6464: The switcher models ANI-MOD1616, ANI-MOD3232, and ANI-MOD6464 share the same function buttons, the only difference is the chassis height and number of I/O’s. The front panel of ANI-MOD1616/3232/6464 is shown as below. r y w q e t 1. IR: IR sensor, receive IR signal sent from IR remote 2. Power Indicator: Illuminate red once powered on 3. LCD Screen: Display real-time operation status 4.
A NEUVIDEO FRONT PANEL control Front Panel Button control ANI-MOD88 Users can control ANI-MOD88 rapidly and directly with its front panel buttons. Here is a brief operation guide to front panel buttons. Note: Format: “Input Channel” + “Switch Mode” +“Output Channel” 1. “Switch Mode”: Audio & Video synchronal (AV) or separate switching mode (Audio/ Video) 2. “Input Channel”: Fill with the number of input channel to be controlled 3.
A NEUVIDEO CHANGEABLE CARDS Changeable Cards Introduction & Installation The various ANI-MOD chassis units are designed to work with various changeable input/ output cards, which can be installed in any ANIMOD empty slot (these cards are hot-swappable). Cards are connection specific, designed to accept signals such as DVI, HDMI, VGA, HDBaseT™, and SDI.
A NEUVIDEO CHANGEABLE CARDS VGA Signal Card ANI-IN-VGA/ANI-IN-VA & ANI-OUT-VGA Video Input Video Output Input (4) VGA Output (4) VGA Input Connector Female 15 pin HD Output Connector Female 15 pin HD Input Level 0.5 ~ 2.0Vp-p Output Level 0.5 ~ 2.0Vp-p Input Impedance 75Ω Output Impedance 75Ω Audio Input Audio Output Input (4) Stereo Audio Output (4) Stereo Audio Input Connector 3P Captive connector Output Connector 3.
A NEUVIDEO CHANGEABLE CARDS Connect the devices via VGA converting cable as shown: • Connect with Component Video (YPbPr) Source • Connect with Composite Video (C-VIDEO) Source *(4) Male VGA to female YPbPr cable (Only included with the ANI-IN-VGA/ANI-IN-VA cards) *(4) Male VGA to female S-video & RCA (C-video) cable (Only included with the ANI-IN-VGA/ANI-IN-VA cards) Component Video Dongle S-Video or Composite Video Dongle 9
A NEUVIDEO CHANGEABLE CARDS SDI Signal Card ANI-IN-SDI & ANI-OUT-SDI Input Output Input (4) SDI Output (4) SDI Input Connector Female BNC Output Connector Female BNC Input Level 0.8Vp-p ± 10% Output Level 0.8Vp-p ± 10% Input Impedance 75Ω Output Impedance 75Ω Gain Unity Transmission Distance 300M (Max) Video Standard SMPTE 292M, SMPTE 259M, SMPTE 424M, ITU-RBT.601, ITU-RBT.1120 Audio Bits per Sample 18 bits per channel, 2 channels (L, R) Input Return Loss < -14dB@1MHz ~ 1.
A NEUVIDEO CHANGEABLE CARDS HDBaseT™ Card ANI-IN-HDBT-4K & ANI-OUT-HDBT-4K Input Output Input (4) RJ45 Output (4) RJ45 Input Connector Female RJ45 / 3.5mm mini jack for IR (3) poles captive screw connector for RS-232 Output Connector Female RJ45 / 3.5mm mini jack for IR (3) poles captive screw connector for RS-232 Input Impedance 75Ω Output Impedance 75Ω Gain 0dB ~ 10dB@100MHz Bandwidth 6.
A NEUVIDEO CHANGEABLE CARDS HDMI 4K2K Card ANI-IN-HDMI-4K & ANI-OUT-HDMI-4K Video Input Audio Input Input (4) HDMI Input (4) Analog Input Connector Female HDMI Input Connector 3.5mm pluggable terminal block Min.~ Max. Level T.M.D.S. 2.9V~3.3V Input Impedance 75Ω Input Impedance 100Ω (Differential) Frequency Response 20Hz~20KHz Video Output Audio Output Output (4) HDMI Output (4) Stereo Output Connector Female HDMI Output Connector 3.5mm Stereo audio connector Min.~ Max.
A NEUVIDEO CHANGEABLE CARDS 4K2K FIBER Card ANI-IN-4K2KF & ANI-OUT-4K2KF Input Output Input (4) Fiber Optical Output (4) Fiber Optical Input Connector SPF Fiber Optical Connector Output Connector SPF Fiber Optical Connector Fiber Type Multi-mode, Single mode Fiber Type Multi-mode, Single mode Data Rate 10.
A NEUVIDEO AUDIO CARDS AUDIO Card ANI-MOD88 Only Input Output Input (8) stereo Output (8) stereo Input Connector 3.5mm captive screw connectors (5) pole Output Connector 3.5mm captive screw connectors (5) pole Input Impedance >10KΩ Output Impedance 50Ω Frequency Response 20Hz~20KHz, ±0.5dB CMRR >90dB@20Hz~20KHz Stereo Channel Separation >80dB@1KHz THD + Noise 1% @1KHz 0.
A NEUVIDEO REMOTE CONTROL IR Remote control With the IR remote, ANI-MOD could be controlled remotely. As the function buttons on the IR remote are the same with the ones on the front panel, the IR remote shares the same operations and commands with the control panel.
A NEUVIDEO System Connection Usage Precautions 1. System should be installed in a clean environment and has a prop temperature and humidity. 2. All of the power switches, plugs, sockets and power cords should be insulated and safe. 3. All devices should be connected before power on. Connection Diagram Application ANI-MOD series has a good application in various occasions, such as radio & television, multi-media meeting room, big screen displaying, television education and command & control center etc.
A NEUVIDEO RS-232 Control Connection of RS-232 Communication Port Besides the front control panel and IR remote, the ANI-MOD can also be controlled by far-end control system or through the Ethernet control via the RS-232 communication port. This RS-232 communication port is a female 9- D connector. The definition of its pin layout is shown in the table below. No.
A NEUVIDEO RS-232 Control Remote Command System from a Personal Computer The ANI-MOD Matrix series can be controlled remotely from a personal computer. The control signal is brought into the ANI-MOD Matrix through the RS-232 connector on the back panel of the unit. The commands are input through software that comes with the ANI-MOD Matrix, once installed in the computer. RS-232 Cable Pins Used Communications Protocol: 1. Transmission Rate: 9600 bps 2.
A NEUVIDEO RS-232 COMMANDS RS-232 Communication Commands With this command system, users are able to control and operate theANI-MOD with RS-232 software remotely. Communication protocol: Baud rate: 9600; Data bit: 8; Stop bit: 1; Parity bit: none. Command Types Command Codes Functions Commands for Main Unit /*Type; Inquire the models information. /%Lock; Lock the keyboard of the control panel on the Matrix. /%Unlock; Unlock the keyboard of the control panel on the Matrix.
A NEUVIDEO RS-232 CommandS ANI-IN-DVS Command Types Command Codes Functions Commands for Signal Cards USER/I/[x]:02xx%; Set the brightness of input [x] to xx, xx=00~99 USER/I/[x]:03xx%; Set the contrast of input [x] to xx, xx=00~99 USER/I/[x]:04xx%; Set the saturation of input [x] to xx, xx=00~99 USER/I/[x]:05xx%; Set the sharpness of input [x] to xx, xx=00~99 USER/I/[x]:0606%; (For 4I-DS/ VA) Auto-adjust VGA input signal USER/I/[x]:0607%; Set picture’s color temperature USER/I/[x]:0608%;
A NEUVIDEO RS-232 CommandS ANI-IN-VA Command Types Command Codes Functions Commands for Signal Cards USER/I/[x]:0622%; Set the signal of input channel [x] to VGA. USER/I/[x]:0623%; Set the signal of input channel [x] to YCBCR. USER/I/[x]:0624%; Set the signal of input channel [x] to SVIDEO. USER/I/[x]:0625%; Set the signal of input channel [x] to CVIDEO. USER/I/[x]:0626%; Set the resolution of input [x] to 1024x768@60Hz. USER/I/[x]:0627%; Set the resolution of input [x] to 1280X720@60Hz.
Communication Protocol and Command Codes A NEUVIDEO Note: 1. Please disconnect all the twisted pairs before sending command EDIDUpgrade[X]. 2. In above commands, “[”and “]” are symbols for easy reading and do not need to be typed in actual operation. 3. Please remember to end the commands with the ending symbols “.” or “;”. 4. Type the command carefully, it is case-sensitive. 5. Commands pertaining to EDID only avails for signal cards that support EDID management. 6.
A NEUVIDEO TCP/IP Control (OPTIONAL) MANAGE TCP/IP SETTINGS TCP/IP default settings: IP is 192.168.0.178, Gateway is 192.168.0.1. To manage the IP address, you first need a PC that can connect to the same sub-net. Note that most modern computers will interpret the correct pins when connected in this fashion. Should you experience any difficulties then you should switch to an Ethernet Crossover cable. Step1. Connect a computer to the Ethernet port of the ANI-MOD Step2.
A NEUVIDEO TCP/IP Control (OPTIONAL) Step6. Change IP • Change IP a) Select the tab “Internet Settings: WAN” to change the IP settings. b) Press the button Apply to save your settings.
A NEUVIDEO GUI INTERFACE Set your matrix size (Model Name has no affect) Control switcher using cross points 25
A NEUVIDEO GUI INTERFACE Select from the detected available COM ports OR Select connection via TCP/IP 26
A NEUVIDEO Safety Operation Guide Troubleshooting & Maintenance Safety Operation Guide To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference. • Unpack the equipment carefully and save the original box and packing material for possible future shipment • Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • Do not dismantle the housing or modify the module.
A NEUVIDEO TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-Neuvideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-Neuvideo, Inc.
