ANI-QUAD 4x4 HDMI VIDEO WALL PROCESSER & MATRIX SWITCH INSTRUCTION MANUAL A-NeuVideo.com | Frisco, Texas 75034 | (317) 456-2461 V.1.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 PACKAGE CONTENTS ..................................................... 1 FEATURES & SPECIFICATIONS ..................................... 2 SYSTEM REQUIREMENTS ............................................ 2 Front Panel ................................................................ 3 Rear Panel ................................................................... 4 OUTPUT MODES .......
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • HDMI, HDCP1.1 and DVI compliant Deep color support 8/10/12 bit source Seamless switching. Most sources switch with zero delay, similar to a cuts only production switcher. Supports three different modes: Matrix mode/ Dual mode/ TV Wall mode • Matrix mode: Can route any (4) Input sources to any (4) Output displays in any combination (4x4).
PANEL DESCRIPTIONS FRONT PANEL q IR Window: IR receiver for signal from the device’s remote control or external IR controller w Power • ON/OFF: Press this button to power On the device or set it to standby mode. • Factory reset to default: Press and hold Power button then connect power to reset the system to Factory default settings. e MENU: • Press this button to bring up the OSD (On Screen Display) menu on screen. • Press “MENU” with “-“button to switch output timing to 720p@60Hz instantly.
PANEL DESCRIPTIONS REAR PANEL q HDMI IN 1~4: Connect HDMI source signal such as STP, DVD player, Blue-ray player, or PC. w HDMI OUT 1~4: Connect HDMI destination device such as a Monitor, Recorder, or distribution system. e Ethernet: Connect to an active Ethernet network for telnet control (refer to section “RS-232 / telnet Commands”) r USB SERVICE ONLY: This slot is reserved for factory use and firmware updates.
OUTPUT MODES OUTPUT MODES VIDEO WALL MODE MATRIX MODE DUAL MODE 5
Remote Control Remote Control q Power: Press this button to switch On the device or press it again to set it to standby mode. w Info: Press this button to show the device’s firmware version. e Out A~D and In 1~4: Press out-put A~D and then press input1~4 to select display input. For example: press Out A then press In 1, output A will display input 1’s image. r MATRIX/DUAL/WALL: Press to switch between Matrix mode, Dual mode and Video Wall mode. t Lock: Press once to lock the keypad and remote control.
RS-232 & Telnet Commands RS-232 & Telnet Commands All commands require a carriage return (0x0D). Commands are case-sensitive.
RS-232 & Telnet Commands RS-232 & Telnet Commands Command Action ANI-QUAD Returns INP999 Check current INPUT INP??? LCK000 Un-lock LCK000 LCK001 Lock LCK001 LCK999 Check current Lock/un-lock status LCK??? MNE001 OSD Menu EXIT No response MND001 OSD Menu DOWN No response MNL001 OSD Menu LEFT (-) No response MNO001 OSD Menu OK No response MNR001 OSD Menu RIGHT (+) No response MNU001 OSD Menu UP No response MNX001 OSD Menu No response MOD001 Matrix mode MOD001 MOD002 Dua
GUI Interface Simple control panel Full function control panel This is a Zip file (compressed). This is the actual software used to control the ANI-QUAD. CLICK THE LINK TO FROM OUR WEBSITE TO DOWNLOAD ANI-QUAD GUI INSTALLATION FILES or use this link http://www.a-neuvideo.com/shop/download/ANI-QUAD_RS232_Ethernet_AP_v16C.ZIP After downloading the contents to your computer, extract the files. Then select setup.exe to begin the installation.
OSD MENU OSD Operation Main Menu PICTURE (*1) Sub Menu ALL DUAL Adjustments Default CONTRAST 0 ~ 100 50 BRIGHTNESS 0 ~ 100 50 SATURATION 0 ~ 100 50 HUE 0 ~ 100 50 DUAL AL 0 ~ 100 DUAL AR DUAL BL DUAL BR OUT A OUT B TV WALL OUT C OUT D D/T RESET ALL RESET ALL EXIT OUTPUT RESOLUTION 720p60 480p, 576p, 720p50, 720p60, 1080i50 (*2), 1080i60, 1080p24, 1080p50, 1080p60, 1024x768, 1280x800, 1280x1024,1366x768, 1440x900,1600x900, 1600x1200,1680x1050, 1920x1200 EXIT AUDIO EDID (*3) LPCM 2
OSD MENU OSD Operation Main Menu BEZEL CORRECTION (*7) Sub Menu Adjustments Default CORRECTION ON, OFF OFF H CORRECTION 0 ~ by output resolution 0 V CORRECTION 0 ~ by output resolution 0 RECALL CANCEL, FAV.1~ 4 CANCEL SAVE CANCEL, FAV.1~ 4 CANCEL IP MODE DHCP, STATIC DHCP STATIC SET IP, MASK, GATE IP EXIT RECALL / SAVE (*8) EXIT ETHERNET BYTE1 192 BYTE2 168 BYTE3 5 BYTE4 155 RE-LINK(*9) TIMEOUT (Min.
TIMING Input Timing Support Timing 480i@59 480p@60 576i@50 576p@50 720p@25,30,50,60, 1080i@50,60 1080p@24,25,30,50,60 640x480@60,72,75,85 720x400@70 800x600@56,60,72,75,85 1024x768@60,70,75,85 1152x864@70,75 1280x720@60cvt 1280x768@60RB,60,75 1280x800@60RB,60,75 1280x1024@60,60cvt,75 1360x768@60 1366x768@60RB,60 1400x1050@60RB,60 1440x900@60RB,60,75 1600x900@60RB 1600x1200@60 1680x1050@60RB,60 1920x1200@60RB OUTput Timing Support Timing 480p60 1024x768@60 576p50 1280x800@60 720p50 1280x1024@60 720p60
WEB GUI GUI SCREEN SHOTS Note: Device power Status must set to ON and Source status must be unlock in order to set the setting accordingly. Click, drag, select or key-in on each selection setting to make the changes immediately.
WEB GUI GUI SCREEN SHOTS 14
WEB GUI GUI SCREEN SHOTS Click on the Ethernet page for IP configuration setting. Both the device (from the OSD setting menu) and the web address entry bar will need to be reset once any change is made on this page.
CONNECTION DIAGRAM CONNECTION DIAGRAM 16
TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-Neuvideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-Neuvideo, Inc.
