User`s manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WNAP 3G Mobile Router
- 3.2 Connect to the WNAP 3G Mobile Router
- 3.3 Management and configuration on the WNAP 3G Mobile Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Mesh Settings
- 3.3.10 Site Survey
- 3.3.11 WPS
- 3.3.12 Schedule
- 3.3.13 LAN Interface Setup
- 3.3.14 WAN Interface Setup
- 3.3.15 Firewall - Port Filtering
- 3.3.16 Firewall - IP Filtering
- 3.3.17 Firewall - MAC Filtering
- 3.3.18 Firewall - Port Forwarding
- 3.3.19 Firewall – URL Filtering
- 3.3.20 Firewall - DMZ
- 3.3.21 Firewall – VLAN
- 3.3.22 Firewall – Virtual Server
- 3.3.23 Route Setup
- 3.3.24 QoS
- 3.3.25 USB Storage
- 3.3.26 Management - Statistics
- 3.3.27 Management - DDNS
- 3.3.28 Management - Time Zone Setting
- 3.3.29 Management – Denial-of-Service
- 3.3.30 Management - Log
- 3.3.31 Management - Upgrade Firmware
- 3.3.32 Management Save/ Reload Settings
- 3.3.33 Management - Password Setup
- 3.3.34 Management - WatchDog
- 3.3.35 Management – Reboot
- 3.3.36 Logout
- 3.3.37 Management - Password Setup
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WNAP 3G MOBILE ROUTER Version: 2.0
55
configuration setting.
3.3.18 Firewall - Port Forwarding
Entries in this table allow you to automatically redirect common network
services to a specific machine behind the NAT firewall. These settings are only
necessary if you wish to host some sort of server like a web server or mail
server on the private local network behind your Gateway's NAT firewall.
Screen snapshot – Firewall - Port Forwarding
Item Description
Enable Port Forwarding Click to enable the Port Forwarding security function.
Enable NAT Loopback Enable/Disable NAT loopback feature
IP Address
Protocol
Port Range
Comment
To forward data packets coming from WAN to a specific IP address that
hosted in local network behind the NAT, fill in the IP address, protocol,
port range and your comments. The Protocol can be TCP, UDP or Both.
The Port Range for data transmission. Comments let you know about
whys to allow data packets forward to the IP address and port number.
Apply Changes Click the Apply Changes button to register the IP address and port
number to Port forwarding list.
Reset Click the Reset button to abort change and recover the previous
configuration setting.
Delete Selected Click to delete the selected IP address and port number that will be
removed from the port-forwarding list.
Delete All Click to delete all the registered entries from the port-forwarding list.