User`s manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WNAP 3G Mobile Router
- 3.2 Connect to the WNAP 3G Mobile Router
- 3.3 Management and configuration on the WNAP 3G Mobile Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Mesh Settings
- 3.3.10 Site Survey
- 3.3.11 WPS
- 3.3.12 Schedule
- 3.3.13 LAN Interface Setup
- 3.3.14 WAN Interface Setup
- 3.3.15 Firewall - Port Filtering
- 3.3.16 Firewall - IP Filtering
- 3.3.17 Firewall - MAC Filtering
- 3.3.18 Firewall - Port Forwarding
- 3.3.19 Firewall – URL Filtering
- 3.3.20 Firewall - DMZ
- 3.3.21 Firewall – VLAN
- 3.3.22 Firewall – Virtual Server
- 3.3.23 Route Setup
- 3.3.24 QoS
- 3.3.25 USB Storage
- 3.3.26 Management - Statistics
- 3.3.27 Management - DDNS
- 3.3.28 Management - Time Zone Setting
- 3.3.29 Management – Denial-of-Service
- 3.3.30 Management - Log
- 3.3.31 Management - Upgrade Firmware
- 3.3.32 Management Save/ Reload Settings
- 3.3.33 Management - Password Setup
- 3.3.34 Management - WatchDog
- 3.3.35 Management – Reboot
- 3.3.36 Logout
- 3.3.37 Management - Password Setup
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WNAP 3G MOBILE ROUTER Version: 2.0
37
subnet mask for it.
Default Gateway If you select the Static IP support on WAN interface, fill in the
default gateway for WAN interface out going data packets.
MTU Size Fill in the mtu size of MTU Size. The default value is 1500
DNS 1 Fill in the IP address of Domain Name Server 1.
DNS 2 Fill in the IP address of Domain Name Server 2.
DNS 3 Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address to be cloned. Refer
to 4.24 What is Clone MAC Address?
Enable uPNP Click the checkbox to enable uPNP function.
Refer to 4.22 What is Universal Plug and Play (uPNP)?
Enable IGMP Proxy Click the checkbox to enable IGMP Proxy.
Enable Ping Access on
WAN
Click the checkbox to enable WAN ICMP response.
Enable Web Server Access
on WAN
Click the checkbox to enable web configuration from WAN side.
Enable FTP Server Access
on WAN
Click the checkbox to enable FTP Server Access on WAN
Enable IPsec pass through
on VPN connection
Click the checkbox to enable IPSec packet pass through
Enable PPTP pass through
on VPN connection
Click the checkbox to enable PPTP packet pass through
Enable L2TP pass through
on VPN connection
Click the checkbox to enable L2TP packet pass through
Apply Changes Click the Apply Changes button to complete the new configuration
setting.
Reset Click the Reset button to abort change and recover the previous
configuration setting.