User`s manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WNAP 3G Mobile Router
- 3.2 Connect to the WNAP 3G Mobile Router
- 3.3 Management and configuration on the WNAP 3G Mobile Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Mesh Settings
- 3.3.10 Site Survey
- 3.3.11 WPS
- 3.3.12 Schedule
- 3.3.13 LAN Interface Setup
- 3.3.14 WAN Interface Setup
- 3.3.15 Firewall - Port Filtering
- 3.3.16 Firewall - IP Filtering
- 3.3.17 Firewall - MAC Filtering
- 3.3.18 Firewall - Port Forwarding
- 3.3.19 Firewall – URL Filtering
- 3.3.20 Firewall - DMZ
- 3.3.21 Firewall – VLAN
- 3.3.22 Firewall – Virtual Server
- 3.3.23 Route Setup
- 3.3.24 QoS
- 3.3.25 USB Storage
- 3.3.26 Management - Statistics
- 3.3.27 Management - DDNS
- 3.3.28 Management - Time Zone Setting
- 3.3.29 Management – Denial-of-Service
- 3.3.30 Management - Log
- 3.3.31 Management - Upgrade Firmware
- 3.3.32 Management Save/ Reload Settings
- 3.3.33 Management - Password Setup
- 3.3.34 Management - WatchDog
- 3.3.35 Management – Reboot
- 3.3.36 Logout
- 3.3.37 Management - Password Setup
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WNAP 3G MOBILE ROUTER Version: 2.0
34
3.3.13 LAN Interface Setup
This page is used to configure the parameters for local area network that
connects to the LAN ports of your WNAP 3G Mobile Router. Here you may
change the setting for IP address, subnet mask, DHCP, etc.
Screen snapshot – LAN Interface Setup
Item Description
IP Address Fill in the IP address of LAN interfaces of this WLAN Access Point.
Subnet Mask Fill in the subnet mask of LAN interfaces of this WLAN Access Point.
DHCP Click to select Disabled, Client or Server in different operation mode of
wireless Access Point.
DHCP Client Range Fill in the start IP address and end IP address to allocate a range of IP
addresses; client with DHCP function set will be assigned an IP address
from the range.
Show Client Click to open the Active DHCP Client Table window that shows the active
clients with their assigned IP address, MAC address and time expired
information. [Server mode only]
Static DHCP Select enable or disable the Static DHCP function from pull-down menu.
[Server mode only]
Set Static DHCP
Manual setup Static DHCP IP address for specific MAC address. [Server
mode only]