User`s manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WNAP 3G Mobile Router
- 3.2 Connect to the WNAP 3G Mobile Router
- 3.3 Management and configuration on the WNAP 3G Mobile Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Mesh Settings
- 3.3.10 Site Survey
- 3.3.11 WPS
- 3.3.12 Schedule
- 3.3.13 LAN Interface Setup
- 3.3.14 WAN Interface Setup
- 3.3.15 Firewall - Port Filtering
- 3.3.16 Firewall - IP Filtering
- 3.3.17 Firewall - MAC Filtering
- 3.3.18 Firewall - Port Forwarding
- 3.3.19 Firewall – URL Filtering
- 3.3.20 Firewall - DMZ
- 3.3.21 Firewall – VLAN
- 3.3.22 Firewall – Virtual Server
- 3.3.23 Route Setup
- 3.3.24 QoS
- 3.3.25 USB Storage
- 3.3.26 Management - Statistics
- 3.3.27 Management - DDNS
- 3.3.28 Management - Time Zone Setting
- 3.3.29 Management – Denial-of-Service
- 3.3.30 Management - Log
- 3.3.31 Management - Upgrade Firmware
- 3.3.32 Management Save/ Reload Settings
- 3.3.33 Management - Password Setup
- 3.3.34 Management - WatchDog
- 3.3.35 Management – Reboot
- 3.3.36 Logout
- 3.3.37 Management - Password Setup
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WNAP 3G MOBILE ROUTER Version: 2.0
23
3.3.7 Wireless - Access Control
If you enable wireless access control, only those clients whose wireless MAC
addresses are in the access control list will be able to connect to your Access
Point. When this option is enabled, no wireless clients will be able to connect if
the list contains no entries.
Screen snapshot – Wireless Access Control
Item Description
Wireless Access Control
Mode
Click the Disabled, Allow Listed or Deny Listed of drop down menu
choose wireless access control mode.
This is a security control function; only those clients registered in the
access control list can link to this WNAP 3G Mobile Router.
MAC Address Fill in the MAC address of client to register this WNAP 3G Mobile
Router access capability.
Comment Fill in the comment tag for the registered client.
Apply Changes Click the Apply Changes button to register the client to new
configuration setting.
Reset Click the Reset button to abort change and recover the previous
configuration setting.
Current Access Control List It shows the registered clients that are allowed to link to this Router.
Delete Selected Click to delete the selected clients that will be access right removed
from this WNAP 3G Mobile Router.
Delete All Click to delete all the registered clients from the access allowed list.
Reset Click the Reset button to abort change and recover the previous
configuration setting.