User`s manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WNAP 3G Mobile Router
- 3.2 Connect to the WNAP 3G Mobile Router
- 3.3 Management and configuration on the WNAP 3G Mobile Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Mesh Settings
- 3.3.10 Site Survey
- 3.3.11 WPS
- 3.3.12 Schedule
- 3.3.13 LAN Interface Setup
- 3.3.14 WAN Interface Setup
- 3.3.15 Firewall - Port Filtering
- 3.3.16 Firewall - IP Filtering
- 3.3.17 Firewall - MAC Filtering
- 3.3.18 Firewall - Port Forwarding
- 3.3.19 Firewall – URL Filtering
- 3.3.20 Firewall - DMZ
- 3.3.21 Firewall – VLAN
- 3.3.22 Firewall – Virtual Server
- 3.3.23 Route Setup
- 3.3.24 QoS
- 3.3.25 USB Storage
- 3.3.26 Management - Statistics
- 3.3.27 Management - DDNS
- 3.3.28 Management - Time Zone Setting
- 3.3.29 Management – Denial-of-Service
- 3.3.30 Management - Log
- 3.3.31 Management - Upgrade Firmware
- 3.3.32 Management Save/ Reload Settings
- 3.3.33 Management - Password Setup
- 3.3.34 Management - WatchDog
- 3.3.35 Management – Reboot
- 3.3.36 Logout
- 3.3.37 Management - Password Setup
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WNAP 3G MOBILE ROUTER Version: 2.0
19
3.3.5 Wireless - Advanced Settings
These settings are only for more technically advanced users who have a
sufficient knowledge about wireless LAN. These settings should not be changed
unless you know what effect the changes will have on your WNAP 3G Mobile
Router.
Screen snapshot – Wireless Advanced Settings
Item Description
Fragment Threshold Set the data packet fragmentation threshold, value can be written
between 256 and 2346 bytes.
Refer to 4.10 What is Fragment Threshold?
RTS Threshold Set the RTS Threshold, value can be written between 0 and 2347
bytes.
Refer to 4.11 What is RTS(Request To Send) Threshold?
Beacon Interval Set the Beacon Interval, value can be written between 20 and 1024
ms.
Refer to 4.12 What is Beacon Interval?
Preamble Type Click to select the Long Preamble or Short Preamble support on the