PowerSaver R7 Wireless Desktop User’s Guide Model: RK(S)-5&R7-20D www.a4tech.
PowerSaver R7 Wireless Desktop THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Federal Communications Commission Requirements The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
PowerSaver R7 Wireless Desktop INTRODUCTION Congratulations on your purchase! PowerSaver R7 Wireless Desktop is the optimal high science products for power & desktop space saving. Its innovative lightweight, mini & thin wireless keyboard design gives you a consistent desktop look as well as an amazingly high level of comfort. your new RF-Mouse is designed with R7 Extremely Low-Power Technology only requires 8mA electric current while others require 25mA.
PowerSaver R7 Wireless Desktop Hardware 1. IBM or compatible system 2. UBS v1.1 or higher interface 3. Hard Disk Driver 4. USB Port Operating System Windows®98/Me/2000/2003/XP/X64 Inserting the Batteries z Install 2 AAA alkaline（or rechargeable batteries）in the wireless keyboard. 1. Remove the battery compartments cover on the bottom of the keyboard by squeezing the cover in front the tab to release it. 2.
PowerSaver R7 Wireless Desktop z Install 2 AAA alkaline（or rechargeable batteries）in the wireless mouse. 1. Press the tab on the bottom of the mouse cover as shown here and remove the cover. 2. Insert the supplied batteries, making sure that the positive (+) and negative (-) ends of the battery match the polarity indicators inside the battery housing. 3. Slide the batter cover back into position until it “clicks” firmly into place.
PowerSaver R7 Wireless Desktop To connect the receiver Insert the Receiver USB port connector into the available computer USB port. You can choose anyway to connect the USB receive with computer as blow: For PC computer usage: 1. Insert the USB receive mouse port connector into the USB port on the USB extend cable (accessories), 2. Insert the USB receives mouse port connector into the USB HUB port.
PowerSaver R7 Wireless Desktop 1. For optimal performance, place the receiver at least 8 inches (20 centimeters) away from other electrical devices, such as the computer, the monitor, or external storage drives. 2. The RF-Mouse should be no farther than 4 feet (1. 5meter) from the mouse receiver. This will ensure optimal communication between the Keep 8 inches Keep 4 feet mouse and receiver. Operating Hints: For optimal performance and RF reception: 1.
PowerSaver R7 Wireless Desktop Establish Frequency Channel and ID Code Step one: how Connecting the Wireless Keyboard ID Code? 1. USB RF Mouse Receiver: lanuch frequency channel and ID code to RF-keyboard Press and release the connect button on the front of USB receiver (shown as right image), the GREEN PWR LED light turns “Off” and starts “Blinking. 2.
PowerSaver R7 Wireless Desktop Step two: how to Connecting the Wireless Mouse ID Code? 1. USB RF Mouse Receiver: lanuch frequency channel and ID code to RF-Mouse Press and release the connect button on the front of USB receiver (shown as right image), the GREEN PWR LED light turns “Off” and starts “Blinking. 2.
PowerSaver R7 Wireless Desktop the right frequency channels and ID codes are launched successfully between the receiver and the mouse, otherwise, repeat the procedures of the right frequency channel and ID codes. You are now ready to use the mouse. Note：The connect button of wireless optical mouse have two functions. One function is correspond frequency with USB receiver. Other function is power switch.
PowerSaver R7 Wireless Desktop Low Battery Warning when your battery power is low, Smart wheel LED light turns to Red for 0.3 seconds and it will be off after 0.9 seconds in interval Note: Removing the batteries will require you to synchronize it with the receiver again the next time you turn it back on. Practical electrical current usage text sheet (on white paper) Battery Voltage (V) Use Electrical Current (mA) 3.3 6.9 3.2 7.0 3.1 7.3 3.0 7.4 2.9 7.
PowerSaver R7 Wireless Desktop Intelligent 4 Power-Saving (SLEEP MODE)： There are 4 sleep mode features activating PowerSaver RF-Mouse Mouse status Electrical Current usage(mA) Savable electricity(mA) idle mode 2.1 5.9 5 seconds non-operation sleeping mode 0.8 7.2 70 seconds non-operation deep sleeping mode 0.1 7.9 30 minute non-operation turns off automatically 0.01 7.
Hot Keys PowerSaver R7 Wireless Desktop Default Functions Cut off the computer power Power Back Back to previous page Forward Forward to next page Refresh Home page Search E -mail Refresh the page Access your default web page. Web search Launches an e-mail application. TECH SUPPORT For tech support, please visit our website at http://support.a4tech.com/ or email us at support@a4tech.
