PowerSaver Wireless Optical Mouse User’s Guide Model: R7-70D www.a4tech.
R7 PowerSaver Wireless Optical Mouse THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Federal Communications Commission Requirements The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
R7 PowerSaver Wireless Optical Mouse INTRODUCTION Congratulations on your purchase! Your new RF-Mouse R7 PowerSaver Office 7Keys is designed with R7 Extremely Low-Power Technology only requires 8mA electric current while others require 25mA. Wow! Just turn your mouse battery –life 3 times longer.
R7 PowerSaver Wireless Optical Mouse Hardware 1. IBM or compatible system 2. UBS v1.1 or higher interface 3. Hard Disk Driver 4. USB Port Operating System Windows®98/Me/2000/2003/XP/x64, Mac OS 8.6 ~ 10.X z This user’s guide describes how to： 1. Connect the receiver to your computer 2. Set up the wireless link and use the mouse 3 .
R7 PowerSaver Wireless Optical Mouse Inserting the Batteries 1. Press the tab on the bottom of the mouse cover as shown here and remove the cover. 2. Insert the supplied batteries, making sure that the positive (+) and negative (-) ends of the battery match the polarity indicators inside the battery housing. 3. Slide the batter cover back into position until it “clicks” firmly into place.
R7 PowerSaver Wireless Optical Mouse To connect the receiver Insert the Receiver USB port connector into the available computer USB port. You can choose anyway to connect the USB receive with computer as blow: For laptop computer usage: Insert the USB mouse port connector into the USB port on laptop computer. Easy take and use. For PC computer usage: 1. Insert the USB receive mouse port connector into the USB port on the USB extend cable (accessories), 2.
R7 PowerSaver Wireless Optical Mouse Locating the USB RF-Mouse Receiver Your RF-Mouse has limitations on the range or distance from its receiver. To make sure that your mouse sends and receives properly, refer to the following instructions: 1. For optimal performance, place the receiver at least 8 inches (20 centimeters) away from other electrical devices, such as the computer, the monitor, or external storage drives. 2. The RF-Mouse should be no farther than 4 feet (1. 5meter) from the mouse receiver.
R7 PowerSaver Wireless Optical Mouse Establish Frequency Channel and ID Code USB RF Mouse Receiver: lanuch frequency channel and ID code to RF-Mouse Press and release the connect button on the front of USB receiver (shown as right image), the GREEN PWR LED light turns “Off” and starts “Blinking.
R7 PowerSaver Wireless Optical Mouse Wireless optical mouse : Respond frequency channel and ID code from Receiver Press and release (1 second) the connect button on the bottom of mouse, the RED PWR LED light turns “Off” and starts “Blinking with right frequency channel and ID code .
R7 PowerSaver Wireless Optical Mouse Power Management Manual Power on/off method 1. To power the mouse on, please press and release the switch bottom of the mouse within in 1 second. 2. Turn off the mouse while traveling or when you don’t use it. Please press and release the switch bottom of the mouse within 4 seconds. (if you use this mouse , you must to power the mouse on again) Automatic Power on/off method If this mouse is keep non-operation in 30 minute, Mouse turns off automatically.
R7 PowerSaver Wireless Optical Mouse Practical electrical current usage text sheet (on white paper) Battery Voltage (V) Use Electrical Current (mA) 3.3 6.9 3.2 7.0 3.1 7.3 3.0 7.4 2.9 7.6 Intelligent 4 Power-Saving (SLEEP MODE)：There are 4 sleep mode features activating PowerSaver mouse Mouse status Enter Sleep mode Electrical Current usage(mA) Savable electricity(mA) 200 milliseconds idle mode 2.1 5.9 5 seconds non-operation sleeping mode 0.8 7.
R7 PowerSaver Wireless Optical Mouse How to install 2X-Office Software **** For Windows 98/ME/2000/2003/XP/X64 1. MUST: Please uninstall any previous mouse driver before installing the 2X-OFFICE 2. MUST: Make sure you have completely finished setting up your receiver and mouse 3. Insert the included Compact Disc (CD) into your CD-ROM 4. Click “Install Driver”. 5. Follow the on screen instruction to complete your installation 6. Restart your computer after the driver has been installed 7.
R7 PowerSaver Wireless Optical Mouse How to program your mouse bottoms? z Open your Mouse Properties. First Tab: Section I: 1. Button Button Assignment The mouse image that appears in the first section is a key to numbers listed to the right. For example， # 1 button has been assigned as “Main Button” by default and it’s not programmable. MOUSE PROPERTY # 2 button has been assigned as “Right Button” which works as right click for your mouse # 3 button has been assigned as “Pan” function by default.
R7 PowerSaver Wireless Optical Mouse for convenient shortcut #4 、#5 buttons can be set as either regular programmable buttons or Office-Button functions. The 4th and 5th as the coupling button to makes shortcut command from Office-jump such as “OPEN, CLOSE”; “DELETE, REPLY”, “ZOOM IN, ZOOM OUT”…etc. which may be easily changed by one click on the 6th OfficeJump button.
R7 PowerSaver Wireless Optical Mouse Learn how to use the “Office Button Options 1. There are 2 ways to open the “Office-Button” menu (right) ● Click the “Office-Button Option” in the Mouse Properties ● Click 6th “Double active Button” located on your physical Mouse Body and will bring you the small picture: 2. Once you click on A4 company logo, you will see the Office Button menu like the figure on the right big image(Office-Button menu) 3.
R7 PowerSaver Wireless Optical Mouse After selected Office Command set No.1 - Copy-Paste . You can adjust your paragraph length or edit sentences with simply two clicks. Instead of looking for copy icon and paste icon in the MS Word or Ctrl+C and Ctrl+V on the Keyboard. Or you can select No.15 - Zoom In- \Zoom out to enlarge the page view size to match your eyesight needs. When you are in Microsoft Excel After selected Office command set No.
R7 PowerSaver Wireless Optical Mouse TECH SUPPORT For tech support, please visit our website at http://support.a4tech.com/ or email us at support@a4tech.
