Instruction Manual Manuel d’instructions Manual de instrucciones Manuale di Istruzioni Bedienungsanleitung 使用手册 WM+PD4001301
UM-101 Digital Sphygmomanometer Instruction Manual Contents 1. Dear Customers ................................................................................2 2. Preliminary Remarks .........................................................................3 3. Notes for Proper Use.........................................................................4 4. Parts Identification .............................................................................6 5. Symbols..................................
1. Dear Customers Congratulations on purchasing a state-of-the-art A&D sphygmomanometer, one of the most advanced monitors available on the market today. Designed for ease of use and accuracy, this monitor will facilitate your daily blood pressure regimen. We recommend that you read through this manual carefully before using this device for the first time. Applicable Patient: Environment for use: This sphygmomanometer is designed for use on adults only. The device is for indoor use.
2.
Training The healthcare provider should stop the examination if there is an abnormality, such as a patient feeling excessive arm pain, and remove the cuff to protect the patient. Repair Do not attempt to open the device. Contact your nearest A&D authorized representative and they will repair or replace the device. Blood Pressure Measurement This device is designed for use with adults. Do not use the device on patients using heart-lung support equipment.
During Use This device should be used by trained professionals. Stop the examination immediately, if the patient feels pain during a measurement or if the device does not work properly. Stop using the device if you notice any abnormalities (for example; liquid inside the device) and request a full service. After Use Clean the device, cuff and accessories before any subsequent uses. Do not pull or kink the tubes. Do not use any organic solvent (for example; antiseptic solution, etc.) to clean the device.
4. Parts Identification Main Body and Accessories Cuff connector Pressure bar display Numerical display MARKER button ON/OFF button Exhaust valve Rubber bulb Cuff 1.5V Batteries (LR6 or AA) Band for attaching a stethoscope on the arm Instruction manual Function ON/OFF Button MARKER button Numerical display Turns on or off the device. During measurement............ Puts a marker at a pressure value After turned off ...................... Indicates a lifetime counter During measurement............
5. Symbols Symbols Function / Meaning Recommended Action Standby and Turn the device on. MARKER Pressure value holding and lifetime counter. Battery installation guide SN Serial number Date of manufacture Type BF: Device, cuff and tubing are designed to provide special protection against electrical shocks. Full Battery Low Battery The battery power indicator during measurement. The battery is low when it blinks. Pressure remains in Cuff. Exhaust it with the exhaust valve. Measurement overtime.
6. Using the Monitor Installing / Changing the Batteries 1. Remove the battery cover. 2. Insert a new set of batteries into the battery compartment as shown. Make sure the polarities (+) and (-) are correct. Use only LR6, AA or equivalent batteries. 3. Close the battery cover. CAUTION Insert the batteries in the battery compartment. If not, the device will not work. When (LOW BATTERY mark) blinks in the LCD display, replace all batteries with new ones. Do not mix old and new batteries.
Attaching the Arm Cuff 1. Wrap the cuff around the upper arm, about 2 ~ 3 cm above the elbow as shown on right. Place the cuff directly against the skin, as clothing may cause a faint pulse and could result in a measurement error. 2. Constriction of the upper arm, caused by rolling up a shirtsleeve, may interfere with accurate readings. 3. Make sure that the index points are within the range. 4. Attach a stethoscope on the arm with accessory band. RANGE INDEX Cuff 2 ~ 3 cm Band Stethoscope 7.
4. When inflation is complete. Turn the exhaust valve screw to release air slowly. Measure the systolic pressure and the diastolic pressure by stethoscopy. 5. The pulse rate is shown on the numerical display when the measurement is complete, and meets the following conditions. When you pressurize 80mmHg or higher for the measurement. When the pressure drops to 20mmHg or lower. 6. Turn the exhaust valve screw counterclockwise to release all the air from the cuff.
9. Troubleshooting Problem Nothing appears in the display, even when the power is turned on. Possible Reason Recommended Action Batteries are empty. Replace all batteries with new ones. Reinstall the batteries with their Battery polarities negative and positive ends matching are not in the those indicated in the battery correct position. compartment. The cuff is not Fasten the cuff correctly. fastened properly.
11. Technical Data Model Measurement method Measurement range Numerical display Pressure bar display Measurement accuracy Numerical display Pressure bar display Power supply Upper arm circumference Classification EMC Operating condition Storage condition Dimensions Weight UM-101 Stethoscopy with stethoscope Pressure: Pulse: Pressure: 0 ~ 300 mmHg 30 ~ 200 beats / minute 20 ~ 280 mmHg Pressure: ±3 mmHg Pulse: ±5 % Pressure: ±4 mmHg 2 x 1.
A&D Co.,Ltd. 1-243 Asahi, Kitamoto-shi, Saitama 364-8585 JAPAN Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119 A&D INSTRUMENTS LTD. Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxon OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D MERCURY PTY. LTD.
