Precision Health Scale UC-321PL Instruction Manual Manuel d’instructions Manual de Instrucciones Manuale di Istruzioni Bedienungsanleitung Gebruiksaanwijzing 使用手册 1WMPD4002089
Contents Before Use Precautions -------------------------------------------------------------------------------------- 1 Scale Components ------------------------------------------------------------------------------ 2 Display Symbols --------------------------------------------------------------------------------- 3 Installing (or Replacing) Batteries ---------------------------------------------------------- 3 Operations Basic Measurement -------------------------------------------------------------------
Scale Components Display Back Ready/Complete Symbol Low Battery Indicator Slide Switch Front Measurement Switch Battery Compartment The following measurements can be selected by the slide switch and are classified into two categories - WEIGHT A and WEIGHT B. Within WEIGHT A and WEIGHT B, you have a choice to select and have your weight displayed in kg or lb. The difference between WEIGHT A and WEIGHT B is the speed of communication from the data port to another device (e.g.
Display Symbols Ready/Complete symbol. This symbol is displayed when the measurement display is stable. Low battery indicator. If this symbol is displayed, replace all four batteries with new ones. Installing (or Replacing) Batteries Caution Insert each battery with its positive (+) and negative (-) terminals properly aligned with the corresponding symbols in the battery compartment. Improper installation of the batteries may cause battery leakage.
Basic Measurement Measuring Your Weight 1. Set the slide switch to the correct mode. Example: Set the slide switch to [WEIGHT B]. Set the slide switch to the correct mode Press the measurement switch 2. Press the measurement switch gently. All display segments are displayed for several seconds. Ready/Complete symbol symbol is displayed. 3. Wait until the Wait until “0.0 kg /0.0 lb” and the Ready/Complete are displayed. symbol Note: If “0.0 kg /0.
Basic Measurement Measuring an Infant or Small Animal Set the slide switch to the correct mode 1. Set the slide switch to the correct mode. Example: Set the slide switch to [WEIGHT B]. Press the measurement switch Step on the scale 2. Press the measurement switch gently and step on the scale. All display segments are displayed for several seconds. Step on the scale without any baby Ready/Complete symbol or animal in your arms before “0.0 kg /0.0 lb” is displayed. kg 3.
Measuring Your Weight on a Carpet Place the scale on a solid level surface, such as tile, wood, or laminate flooring. If the scale must be used on a carpet, be sure to attach the plastic add-on feet. Steps for Attaching the Add-on Feet 1. Each add-on foot has two pins. Match those pins to the holes on the scale leg and insert firmly. 2. Attach add-on feet on all four legs. Notes Please be careful not to fall when using the add-on feet. We recommend using this scale on a solid and level surface.
Specifications Digital display Liquid crystal display, 25 mm character height Maximum capacity 200 kg / 450 lb Minimum display 0.1 kg / 0.2 lb Power source Four type AA batteries (R6P or LR6, 1.5 volt x 4) Battery life Approximately 1000 measurements Accessories Add-on feet (4), Instruction manual, Batteries (4) Specifications are subject to change without prior notice or any obligation on the part of the manufacturer.
Before Requesting Service Problems Nothing is displayed by pressing the measurement switch. Corrective Action Check the battery installation. Replace all four batteries with new ones. Remove and reinstall the batteries. “88888” remains displayed. Place the scale on a solid level “e- 0” is displayed. The difference between an estimated surface. Remove any foreign objects that might weight and a measured weight is be touching the bottom of the scale. excessive.
1-243 Asahi, Kitamoto-shi, Saitama 364-8585 JAPAN Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119 A&D INSTRUMENTS LTD. Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95131 U.S.A. Telephone: [1] (408) 263-5333 Fax: [1] (408)263-0119 A&D Australasia Pty Ltd.
