Digital Blood Pressure Monitor Model UA-852 Instruction Manual Original Manuel d’instructions Traduction Manual de Instrucciones Traducción Manuale di Istruzioni Traduzione Bedienungsanleitung Übersetzung 使用手冊 翻譯 1WMPD4001655D
Contents Dear Customers.................................................................... 2 Preliminary Remarks ............................................................. 2 Precautions........................................................................... 2 Parts Identification................................................................ 4 Symbols................................................................................ 5 Operation Mode......................................................
Dear Customers Congratulations on purchasing a state-of-the-art A&D blood pressure monitor, one of the most advanced monitors available today. Designed for ease of use and accuracy, this device will facilitate your daily blood pressure regimen. We recommend that you read through this manual carefully before using the device for the first time. Preliminary Remarks This device conforms to the European Directive 93/42 EEC for Medical Products. This is made evident by the mark of conformity.
When reusing the device, confirm that the device is clean. Do not modify the device. It may cause accidents or damage to the device. To measure blood pressure, the arm must be squeezed by the cuff hard enough to temporarily stop blood flow through the artery. This may cause pain, numbness or a temporary red mark to the arm. This condition will appear especially when measurement is repeated successively. Any pain, numbness, or red marks will disappear with time.
Parts Identification Artery Position Mark CLOCK Button Button Proper Fit Range Air Connector Plug Display MEMORY Button Index Mark Arm Cuff Air Hose Button (Blue illumination) START Air Socket Battery Compartment Battery Cover 1.5V Batteries (R6P, LR6 or AA) DC Jack Part of Display MEMORY Pressure Bar Indicator and WHO Classification Indicator Heart Mark I.H.B.
Symbols Symbols Function / Meaning Recommended Action Standby and Turn the device on. Battery installation guide Direct current SN Serial number Date of manufacture Type BF: Device, cuff and tubing are designed to provide special protection against electrical shocks. The indicator while measurement is in Measurement is in progress. It blinks while detecting the progress. Remain as still pulse. as possible. Irregular Heartbeat indicator. (I.H.B.
Symbols Function / Meaning EU-representative Manufacturer Class II device Refer to instruction manual/booklet Polarity of DC jack Recommended Action Operation Mode 1. Normal Measurement With Storing Data (Refer to page 11) Press the START button. Blood pressure is measured and data is stored within the device. The device can store the last ninety sets of data in memory. 2. Recalling The Data (Refer to page 13) Press the MEMORY button to recall the data. First, average of all the data is shown.
Using The Monitor Installing / Changing The Batteries 1. Slide the battery cover to open it. 2. Remove the used batteries and insert new batteries into the battery compartment as shown, taking care that the polarities (+) and (-) are correct. 3. Slide the battery cover to close it. Use only R6P, LR6 or AA batteries. Step 2 Step 1 Step 3 CAUTION Insert the batteries as shown in the battery compartment. If not, the device will not work.
Using The Monitor Adjusting The Built-in Clock The monitor has a built-in 24-hour clock. We recommend Press and hold that you adjust the clock prior to use. the CLOCK button 1. Press and hold the CLOCK button until the digits start blinking. 2. Select the year using the button. Press the CLOCK button to set the current year and move to month/day selection. The date can be set anywhere between the years 2006 and 2056. Year Month button. 3.
Using The Monitor Alarm ON/OFF Mark On The Display When the alarm is on, a “ ” appears on the LCD. To turn the alarm off, simply press the CLOCK button once. The alarm will sound for 1 minute. To stop the alarm sound, press any button once. Selecting the Correct Cuff Size Using the correct cuff size is important for an accurate reading. If the cuff is not the proper size, the reading may yield an incorrect blood pressure value. The arm size is printed on each cuff.
Using The Monitor Applying The Arm Cuff Do not roll up shirtsleeve tightly 1. Wrap the cuff around the upper arm, about 1-2 cm above the inside of the elbow, as shown. Place the cuff directly against the skin, as clothing may cause a faint pulse, and result in a measurement error. Cuff Artery position mark 2. Constriction of the upper arm, caused by tightly rolling up a shirtsleeve, may prevent accurate readings. 3. Confirm that the index within the proper fit range.
Measurements Model UA-852 is designed to detect the pulse and to inflate the cuff to a systolic pressure level automatically. If your systolic pressure is expected to exceed 230 mmHg or you use the optional small cuff, read "Measurement With The Desired Systolic Pressure" on the next page. Normal Measurement 1. Place the cuff on the arm (preferably the left arm). Sit quietly during measurement. 2. Press the START button. 0 (zero) is displayed blinking briefly.
Measurements Measurement With The Desired Systolic Pressure If your systolic pressure is expected to exceed 230 mmHg or you use the optional small cuff, use this procedure. 1. Place the cuff on the arm (preferably the left arm). 2. Press and hold the START button until a number about 30 to 40 mmHg higher than your expected systolic pressure appears. 3. Release the START button to start measurement, when the desired number is reached.
Recalling Memory Data Note: This device stores the last ninety measurements in memory. The data is retained as long as the batteries are in the device. When you remove the batteries or the batteries are drained, the data will be erased. 1. Press the MEMORY button. Average of stored data is shown. M Average of Systolic pressure Diastolic pressure Nos. of Data 2. Press the MEMORY button. The most recent data is displayed. 3. Then, each time the MEMORY button is pressed, the previous data is displayed. 4.
What Is An Irregular Heartbeat Model UA-852 blood pressure monitor provides a blood pressure and pulse rate measurement even when an irregular heartbeat occurs. An irregular heartbeat is defined as a heartbeat that varies by 25% from the average of all heartbeats during the blood pressure measurement. It is important that you be relaxed, remain still and do not talk during measurements. Note: We recommend contacting your physician if you see this indicator frequently.
About Blood Pressure What Is Blood Pressure? Blood pressure is the force exerted by blood against the walls of the arteries. Systolic pressure occurs when the heart contracts. Diastolic pressure occurs when the heart expands. Blood pressure is measured in millimeters of mercury (mmHg). One's natural blood pressure is represented by the fundamental pressure, which is measured first thing in the morning while one is still at rest and before eating.
Blood Pressure described in this manual to get to know your normal blood pressure. Regular readings give a more comprehensive blood pressure history. Be sure to note date and time when recording your blood pressure. Consult your doctor to interpret your blood pressure data. Typical fluctuation within a day (Measured every five minutes) Systolic Diastolic Sleep Troubleshooting Problem Possible Reason Nothing Batteries are drained.
Maintenance Do not open the device. It uses delicate electrical components and an intricate air unit that could be damaged. If you cannot fix the problem using the troubleshooting instructions, request service from your dealer or from the A&D service group. The A&D service group will provide technical information, spare parts and units to authorized dealers. The device was designed and manufactured for a long service life.
Accessory AC adapter TB-233 TB-233C TB-233BF The adapter is to connect the blood pressure monitor to a power source at home. Please contact your local A&D dealer for purchasing. The AC adapter is required to be inspected or replaced periodically.
1-243 Asahi , Kitamoto-shi, Saitama 364-8585, JAPAN Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119 A&D INSTRUMENTS LIMITED Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95131, U.S.A.
