Digital Blood Pressure Monitor Model UA-767 BT Instruction Manual Original Manuel d’instructions Traduction Manual de Instrucciones Traducción Manuale di Istruzioni Traduzione Bedienungsanleitung Übersetzung Gebruiksaanwijzing Vertaling 使用手冊 1WMPD4001357D 翻譯
Contents Dear Customers.................................................................... 1 Preliminary Remarks ............................................................. 2 Precautions........................................................................... 2 Parts Identification................................................................ 4 Symbols................................................................................ 5 Using the Monitor ..................................................
Preliminary Remarks This device conforms to the European Directive 93/42 EEC for Medical mark of conformity. Products. This is made evident by the (0123: The reference number to the involved notified body) The device complies with the statutory EMC (Electromagnetic Compatibility) directive 89/336/EEC. The WML-40AH is approved in accordance to R&TTE directive transmitter module marked by , manufactured by MITSUMI incorporated to OEM product.
To measure blood pressure, the arm must be squeezed by the cuff hard enough to temporarily stop blood flow through the artery. This may cause pain, numbness or a temporary red mark to the arm. This condition will appear especially when measurement is repeated successively. Any pain, numbness, or red marks will disappear with time. Contraindications The following are precautions for proper use of the device. Do not apply the cuff on an arm with another medical electrical equipment attached.
Parts Identification DC Jack START Button Display Air Connector Plug Air Socket Proper Fit Range Air Hose Index Mark Artery Position Mark Battery Cover Arm Cuff 1.5V Batteries (R6P or AA) Battery Compartment Part of Display MEMORY Systolic Pressure Diastolic Pressure Pressure Bar Indicator Pulse Rate Battery Indicator I.H.B.
Symbols Symbols Function / Meaning Recommended Action Standby and power on. Battery installation guide Direct current SN Serial number Date of manufacture Type BF: Device, cuff and tubing are designed to provide special protection against electrical shocks. The indicator that appears while Measurement is in measurement is in progress. It blinks progress. Remain as still as when the pulse is detected. possible. Irregular Heartbeat indicator. (I.H.B.
Using the Monitor Installing / Changing the Batteries Step 1 1. Slide the battery cover up to open it. 2. Remove the used batteries and insert new batteries into the battery compartment as shown, taking care that the polarities (+) and (-) are correct. 3. Slide the battery cover down to close. Step 3 Step 2 Use only R6P, AA batteries. CAUTION Insert the batteries as shown in the battery compartment. If not, the device will not work.
Using the Monitor Selecting the Correct Cuff Size Using the correct cuff size is important for an accurate reading. If the cuff is not the proper size, the reading may yield an incorrect blood pressure value. The arm size is printed on each cuff. The index and proper fit range, on the cuff, tell you if you are applying the correct cuff. (Refer to "Applying The Arm Cuff" on the next page. ) If the index points outside of the range, contact your local dealer to purchase a replacement cuff.
Using the Monitor Applying the Arm Cuff 1. Wrap the cuff around the upper arm, about 1-2 cm above the inside of the elbow, as shown. Place the cuff directly against the skin, as clothing may cause a faint pulse, and result in a measurement error. Do not roll up shirtsleeve tightly Cuff Artery position mark 2. Constriction of the upper arm, caused by tightly rolling up a shirtsleeve, may prevent accurate readings. 3. Confirm that the index within the proper fit range.
Measurements Model UA-767 BT is designed to detect the pulse and to inflate the cuff to a systolic pressure level automatically. If your systolic pressure is expected to exceed 230 mmHg or you use the optional small cuff, read "Measurement with the desired systolic pressure" on the next page. Normal Measurement 1. Place the cuff on the arm (preferably the left arm). At heart level Sit quietly during measurement. 2. Press the START button.
Measurements Measurement with the Desired Systolic Pressure If your systolic pressure is expected to exceed 230 mmHg or you use the optional small cuff, use this procedure. 1. Place the cuff on the arm (preferably the left arm). 2. Press and hold the START button until a number about 30 to 40 mmHg higher than your expected systolic pressure appears. 3. Release the START button to start measurement, when the desired number is reached.
What is an Irregular Heartbeat Model UA-767 BT blood pressure monitor provides a blood pressure and pulse rate measurement even when an irregular heartbeat occurs. An irregular heartbeat is defined as a heartbeat that varies by 25% from the average of all heartbeats during the blood pressure measurement. It is important that you be relaxed, remain still and do not talk during measurements. Note: We recommend contacting your physician if you see this indicator frequently.
About Blood Pressure What is Blood Pressure? Blood pressure is the force exerted by blood against the walls of the arteries. Systolic pressure occurs when the heart contracts. Diastolic pressure occurs when the heart expands. Blood pressure is measured in millimeters of mercury (mmHg). One's natural blood pressure is represented by the fundamental pressure, which is measured first thing in the morning while one is still at rest and before eating.
Diastolic blood pressure described in this manual to get to know your normal blood pressure. Regular readings give a more comprehensive blood pressure history. Be sure to note date and time when recording your blood pressure. Consult your doctor to interpret your blood pressure data. Typical fluctuation within a day (Measured every five minutes) Systolic Sleep Diastolic PM AM Time Troubleshooting Problem Possible Reason Nothing appears Batteries are drained.
Maintenance Do not open the device. It uses delicate electrical components and an intricate air unit that could be damaged. If you cannot fix the problem using the troubleshooting instructions, request service from your dealer or from the A&D service group. The A&D service group will provide technical information, spare parts and units to authorized dealers. The device was designed and manufactured for a long service life.
Applied part Cuff Useful life Device: 5 years (when used six times a day) Cuff: 2 years (when used six times a day) Wireless communication WML-40AH (MITSUMI Electronics Co. Ltd.) Accessory AC adapter The adapter is to connect the device to a power source at home. TB-233 TB-233C TB-233BF Type BF Please contact your local A&D dealer for purchasing. The AC adapter is required to be inspected or replaced periodically.
1-243 Asahi, Kitamoto-shi, Saitama 364-8585 JAPAN Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119 A&D INSTRUMENTS LIMITED Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95131 U.S.A.
