Digital Blood Pressure Monitor Model UA-1010 Instruction Manual Original Manuel d’instructions Traduction Manual de Instrucciones Traducción Manuale di Istruzioni Traduzione 使用手冊 翻譯 1WMPD4002223C
Contents Dear Customers .......................................................................... 1 Preliminary Remarks.................................................................... 2 Precautions ................................................................................. 2 Parts Identification ...................................................................... 3 Symbols ...................................................................................... 4 Operation Mode ...................
Preliminary Remarks This device conforms to the European Directive 93/42 EEC for Medical Products. This is made evident by the mark of conformity. (0123: The reference number to the involved notified body) The device is designed for use on adults only, not newborns or infants. Environment for use: The device is for use in the home healthcare environment. This device is designed to measure blood pressure and pulse rate of people for diagnosis.
Parts Identification DC Jack Display Button Button SET Button Air Connector Plug START Button Air Socket Air Hose Proper Fit Range Artery Position Mark Index Mark Arm Cuff Battery Compartment Battery Cover 1.5V Batteries (R6P, LR6 or AA) Display MEMORY Average I.H.B.
Symbols Symbols that are printed on the device case Symbols Function / Meaning Standby and Turn the device on. Battery installation guide Recommended Action Direct current SN 2010 Serial number Date of manufacture Type BF: Device, cuff and tubing are designed to provide special protection against electrical shocks.
Symbols Symbols Function / Meaning Recommended Action Previous measurements stored in memory. Average data The battery power indicator during Full Battery Low Battery measurement. The battery is low when it blinks. Unstable blood pressure due to movement during measurement. Replace all batteries with new ones when the mark blinks. Take another measurement. Remain very still during measurement. The systolic and diastolic values are within 10 mmHg of each other. PUL.
Operation Mode 1. Normal Measurement Press the START button. Blood pressure is measured and the data is stored in memory. This device can store the last 90 measurements in memory. 2. Recalling the Data Press the or button to recall the data in memory. The average of all measurements is displayed, as indicated in the figure at the right. Then, each time the button is pressed, the memory data is displayed as follows. Average of all AM (morning) measurements taken between 4:00 and 9:59.
Using the Monitor Installing / Changing the Batteries 1. Remove the battery cover. 2. Remove the used batteries and insert new batteries into the battery compartment as shown, taking care that the polarities (+ and -) are correct. Use only R6P, LR6 or AA batteries. 3. Attach the battery cover. Step 1 Step 3 Step 1 Step 2 CAUTION Insert the batteries as shown in the battery compartment. If installed incorrectly, the device will not work.
Using the Monitor Adjusting the Built-in Clock Press Adjust the clock prior to use. 1. Press the SET button until the year starts blinking. or button. 2. Select the year using the Press the SET button to set the current year and move to month/day selection. The date can be set anywhere between the years 2010 and 2059. or button. 3. Select the month using the Press the SET button to set the current month and move to day selection. or button. 4.
Using the Monitor Selecting the Correct Cuff Size Using the correct cuff size is important for an accurate reading. If the cuff is not the proper size, the reading may yield an incorrect blood pressure value. The arm size is printed on each cuff. The index and proper fit range, on the cuff, tell you if you are applying the correct cuff. (Refer to "Symbols that are printed on the cuff") If the index points outside of the range, contact your local dealer to purchase a replacement cuff.
Using the Monitor Do not roll up shirtsleeve tightly. Applying the Arm Cuff 1. Wrap the cuff around the upper arm, about 1-2 cm above the inside of the elbow, as shown. Place the cuff directly against the skin, as clothing may cause a faint pulse, and result in a measurement error. Cuff Air Hose Artery position mark 2. Constriction of the upper arm, caused by tightly rolling up a shirtsleeve, may prevent accurate readings. 3. Confirm that the index within the proper fit range.
Measurements Before measurement, read “Notes for Proper Measurement” on the next page. Normal Measurement 1. Place the cuff on the arm (preferably the left arm). Sit quietly during measurement. 2. Press the START button. Press All of the display segments are displayed. Zero (0) is displayed blinking briefly. The display changes, as indicated in the All of the display figure at the right, as the measurement segments displayed begins. The cuff starts to inflate.
Measurements Measurement with the Desired Systolic Pressure Model UA-1010 is designed to detect the pulse and to inflate the cuff to a systolic pressure level automatically. Use this method when re-inflation occurs repeatedly or when the results are not displayed even if the pressure decreases to 20 mmHg or less. 1. Place the cuff on the arm (preferably the left arm). 2. Press and hold the START button until a number about 30 to 40 mmHg higher than your expected systolic pressure appears. 3.
Recalling the Memory Data Note: This device stores the last 90 measurements in memory. Press or or button. 1. Press the The average of all measurements and the Average systolic number of data are displayed. (If no data, “0” is displayed. Press the Average diastolic , or START button to turn the Average pulse device off.) Average of all the data button (or the 2. Each time the button to display the data in the reverse order) is pressed, the memory Average systolic data is displayed as follows.
What is an Irregular Heartbeat The UA-1010 blood pressure monitor provides a blood pressure and pulse rate measurement even when an irregular heartbeat occurs. An irregular heartbeat is defined as a heartbeat that varies by 25% from the average of all heartbeats during the blood pressure measurement. It is important that you are relaxed, remain still and do not talk during measurements. Note: We recommend contacting your physician if you see this indicator frequently.
About Blood Pressure What is Blood Pressure? Blood pressure is the force exerted by blood against the walls of the arteries. Systolic pressure occurs when the heart contracts. Diastolic pressure occurs when the heart expands. Blood pressure is measured in millimeters of mercury (mmHg). One's natural blood pressure is represented by the fundamental pressure, which is measured first thing in the morning while one is still at rest and before eating.
described in this manual to get to know your normal blood pressure. Regular readings give a more comprehensive blood pressure history. Be sure to note the date and time when recording your blood pressure. Consult your doctor to interpret your blood pressure data. Troubleshooting Problem Possible Reason Nothing Batteries are drained. appears on the display, even Battery terminals are not when the power in the correct position. is turned on. The cuff does not inflate. Battery voltage is too low.
Maintenance Do not open the device. It uses delicate electrical components and an intricate air unit that could be damaged. If you cannot fix the problem using the troubleshooting instructions, contact the authorized dealer in your area or our customer service department. The A&D customer service will provide technical information, spare parts and units to authorized dealers. The device was designed and manufactured for a long service life.
Weight Approx. 265 g, excluding the batteries Applied part Cuff Useful life Device: 5 years (when used six times a day) Cuff: 2 years (when used six times a day) Accessory AC adapter The adapter is to connect the device to a power source at home. TB-233 Type BF Please contact your local A&D dealer for purchasing. The AC adapter is required to be inspected or replaced periodically.
Asahi 1-243, Kitamoto-shi, Saitama 364-8585, JAPAN Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119 A&D INSTRUMENTS LIMITED Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95131, U.S.A.
